Yeah it's running on last year's fuel . Total smoke fest.
@jamesodell5801
10 ай бұрын
Can you tell me what number hole the purple wire goes in?
@vc8885
Жыл бұрын
Ci sono un sacco di fake di centraline Hackko, e arrivano tutte dalla Cina, io ho cambiato due, 2 Weller prima che una funzionasse! La prima da un sito di elettronica, le seconde dal grande sorriso.
@michaelhunt1802
Жыл бұрын
How do you get to that? Need to hook up turn signal wires.
@hillbillyhangover
Жыл бұрын
Thank you!!!
@Clean-N-ShineInDfw
Жыл бұрын
Can this part be ordered online? I've replaced my instrument cluster and it's not working properly. I think it's probably the connector but the mechanic doesn't want to fix the problem. He didn't examine the connector to see if it was any good. He rushed it and put the new instrument cluster and Mph is still failing as I'm driving. It falls down randomly when driving. Any help would be greatly appreciated
@one_eye_willy6286
8 ай бұрын
Did you ever figure out what the problem was I’m having the same problem there digital Dash or lights popping up every now and then it will jiggle the needle but no light or any check engine lights
@sa8175-x2g
2 жыл бұрын
Hi Bernie. Is this connector called 16-pin connector in repair manuals?
@jmize1991
2 жыл бұрын
Do you know the part # or actual name of the the pig tail? Mine is burnt up. Bought new cluster but can't find pigtail
@robertveldkamp9964
2 жыл бұрын
Do you know what size the pins are and or what they are called? I believe they are a deutsch but I don’t know what size.
@ajv802
2 жыл бұрын
Call Hakko and quote the serial number to confirm it is not a fake. Open it up to confirm.
@berniesworkbench7468
2 жыл бұрын
I opened it up and confirmed all parts are genuine. Its been 4 years now at least and it still works fine.
@ntag411
3 жыл бұрын
Guessing, a cold solder joint somewhere within the unit. Probably not a power connection, sounds like a low power logic issue.
@fullsoundrecording
3 жыл бұрын
This is so strange, and no you can use these in cold environments. I have two 888 units and I use one in Alaska out in the shop newed I say more, not a single problem with either unit in the last 8 years since I purchased them. and I use them a lot. I have replaced the pencil iron on one unit. You are not by chance running AC in your shop that is 60AC volts x 2 one side out of phase? In other words, 60 volts on one side of the plug and 60 volts on the other side and your ground is your neutral? I'm assuming not as if you were you would have thought of this as a potential. problem. Those of us that run 60 x 60 AC volts phase reversed on one side are rare and only do so for specific needs, However, I guess one could forget or purchased a place whit this implemented and forgot. I wonder if they sent you the same unit back. as fare as the base or pencil? And for the future you may want to avoid such rough handling of the pencil as far as slamming it into the holder, I'm not saying it's going to be a killer every time but the element in these are 70volt aliments and are rather brittle so if you do that just in the right way hitting the tip just on the correct spot you will crack or shatter the elements. so maybe a bit more care taken when handling it may well keep it in service much longer in the future. Don't let this be a discouraging experience, I now have a 951 and a full Hakko desolder station as well an SMD station and they are all in Alaska in the cold cold shop well below 15degrees when I walk in and they all work just fine.
@berniesworkbench7468
3 жыл бұрын
OK this is almost 5 years ago now and its still chugging along fine as long as its above seeing your breath temp in the shop. If its a little cold I just put the unit inside my jacket for a couple minutes and its fine. As far as the how I'm placing the iron in the holder... I'm definitely not slamming it in there although the clicking of the metal parts together might sound a little loud to the mic. If it cant take the treatment I give it then I don't want it. I'm not about to play a game of operation (its an old game where you fish plastic body parts out of a hole with tweezers without touching the sides) while I'm trying to get some work done. And I think the fact that its lasted this long supports my case.
@yanz1232
3 жыл бұрын
Can this be why my cluster isnt showing rpm, speed and gas gauge?.. The pins would be tucked in too far?? Last owner changed the cluster after breaking it physically.. Perhaps they ended up pushing the pins too far in the socket... I'll take it appart later at noon. Thanks for the video
@berniesworkbench7468
3 жыл бұрын
Yeah it could be.
@sedsed7518
Ай бұрын
I have a same problem. Mashine was in a water a bit. Now i dont have rpm, fuel gauge speed ets
@abdelfevrio
3 жыл бұрын
good job .. what camera do you use to film the project bro
@manofculture-8045
3 жыл бұрын
Is it a wire cutting machine 🤣
@berniesworkbench7468
3 жыл бұрын
Yes.
@shibafarhat2005
3 жыл бұрын
It's detail info I would like to know how it's done to my Whatsapp 919393374815 or email [email protected]
@Poshoo
3 жыл бұрын
Habano cutter 🤣 awesome!
@psargaco
3 жыл бұрын
What's the final objective?
@miniwarrior7
3 жыл бұрын
Cut cut cut
@sguna9964
3 жыл бұрын
Super 👍👏🤝
@abhijeetdas2919
3 жыл бұрын
my first Arduino project, gesture control car 😂but struggled too much to complete it...
@vishalgaurav4411
3 жыл бұрын
What is powering up that pneumatic cylinder?
@Karan-stee.k
3 жыл бұрын
your first project? kind of lying. If not, then you are smart.
@berniesworkbench7468
3 жыл бұрын
Just noticed this comment. No I'm not that smart, if I was Id be rich, but I had an objective when I started and everything I bought, did, and learned was geared towards building this wire cutter.
@CharlieRunnalls
3 жыл бұрын
First project!.. go big or go home I guess! 😅
@komaldoll7862
3 жыл бұрын
Very very so good worak
@fabiuh991
3 жыл бұрын
First project this month lmao
@rezouki
3 жыл бұрын
This is my college graduation project 2000
@enlapolitecnica5673
3 жыл бұрын
Respect 👍
@partagesappgeekk3547
3 жыл бұрын
Nice 👍
@andressanmartinmorin1898
3 жыл бұрын
Shame on us that made the blink led and felt like tony stark
@babarsayeed6742
3 жыл бұрын
Excellent effort
@karltaylor6409
3 жыл бұрын
lol
@ahmedsamir3099
3 жыл бұрын
Nice
@priyamk.4825
3 жыл бұрын
Subscriber:- 1k Views:-124k
@priyamk.4825
3 жыл бұрын
Lol
@miniwarrior7
3 жыл бұрын
Algorithm:- priceless
@syedadnan9142
3 жыл бұрын
My first project is alcohol detector engine locking system I got second prize in my college
@ebramsherif8300
3 жыл бұрын
I am working on it my college graduation project lol but in a prototype car
@syedadnan9142
3 жыл бұрын
My prototype is also car you can see the video of my project on KZitem my channel is learn animated
@abhijeetdas2919
3 жыл бұрын
which sensor did u used for detecting alcohol?
@syedadnan9142
3 жыл бұрын
Mq3
@abhijeetdas2919
3 жыл бұрын
@@syedadnan9142 ty👍🏻
@Ma_X64
3 жыл бұрын
Add a both-sides-deinsulator.
@user-dl4bt7km4g
3 жыл бұрын
Open source?
@azeemhasansiddiqui320
3 жыл бұрын
Sir good 👍 project boos
@bobbg9041
3 жыл бұрын
Could be a fake. Watch video how to spot a fake. First this id do it open the case and look for a daughter board over the transformer And the custom ic.
@bobbg9041
3 жыл бұрын
Just take it inside the warm area at night. I have the same problem trying to work in the cold. Warm me up I work just fine. To hot forget it.
@bobbg9041
3 жыл бұрын
Its aluminum. Aluminum removes heat faster then almost any other material Becuse the heater is being asked to heat up on a cold surface it cant overcome the cold fast enough to heat up to usable temptures so its in thermol shock. Its probably a protection circuit doing this. You might try not putting it into the base and let it warm up in the air. Just my 2 cents.
@agonymobile
3 жыл бұрын
That can be way faster A knife on a solinoid for car self starter Can cut and back in a milliseconds Some steppers can be drived more faster like 50 Rev/sec.
@siddharthg8801
3 жыл бұрын
Great
@Nathan-mu8zy
3 жыл бұрын
I would just use a 1kg servo instead of a piston for cutting
@robbykhen
3 жыл бұрын
In industrial world, we almost always use pneumatic cylinder to cut things like that, because you might never know if you need more power to cut a bigger size object. That pneumatic have alot of power, and can adjust the speed too.
@abennacerboulaghmane121
3 жыл бұрын
God I like it I wanna mack this shit
@HomeHome-yf8kb
3 жыл бұрын
Ohh u mean ur first project that u called a project
@user-gm9pu7nb6p
3 жыл бұрын
اي الفايد
@priyamk.4825
3 жыл бұрын
My first Arduino project:- LED Light at 13 point( integrated light )
Пікірлер