You can get the vevor train horn set for eighty dollars. It's three times as loud as that
@jimtoughill395
Ай бұрын
That horn sounds like crap. Their advertisement makes it sound super loud. My Hornblaster train horn is so loud people get out of my way real quick. I wouldn't waste my money on Moto horn kit. You can buy something similar from harbor freight for half the money if you think this Moto horn is loud.
@Rockcreekgarageworks
Ай бұрын
Lol that is a awesome comparison.
@frankshanks9726
4 ай бұрын
Not even close to sounding like a train horn.
@Rockcreekgarageworks
4 ай бұрын
Ya I used my phone and the sound is being blocked I will make update soon.
@frankshanks9726
4 ай бұрын
@@Rockcreekgarageworks I have a kit that actually sounds like a train. You need several larger horns and a compressor with a tank like actual trains have. An actual train horn kit is around $1500. Also, it still sounds like a train horn even when recorded with a phone.
@Rockcreekgarageworks
4 ай бұрын
@frankshanks9726 the motohorn kits come with micro direct compressor. I'm cheap so I shop on wish for most stuff 😆.
@frankshanks9726
4 ай бұрын
@@Rockcreekgarageworks 5 gallon tank and compressor minimum.
@Rockcreekgarageworks
4 ай бұрын
@frankshanks9726 I'm looking for a tank to hook up my viair 450 to. Once I get that plummed, I will be switching horns.
@sonofagunny7760
4 ай бұрын
Thanks for sharing your video! I HATE messing with ANYTHING Electrical when it comes to a vehicle! I messed something up 35yrs ago that caused my headlights to go out 1/2 way between Orlando & Daytona Beach late at night
@Rockcreekgarageworks
3 ай бұрын
Thank you. I appreciate it. Ya I've done something similar but it was my turn signals that went out.
@prophinishnyc31
5 ай бұрын
Link?
@ekvictory007
5 ай бұрын
Useful tip: if you really dont want to modify your harness, you can trim male and female tab connectors and plug them right into the harness socket. I isolate mine with a little piece of cardboard between them and carefully secure everything together and seal it with good electrical tape, usually super 33 or super 88 if its in a wheel well or at the nose of the truck.
@Rockcreekgarageworks
5 ай бұрын
I'm going to redo everything in a couple of months bc I'm going to install another horn.
@ekvictory007
5 ай бұрын
@Rockcreekgarageworks I mean, give it a shot. Its just a tab of cardboard, a couple crimps, and some tape; but the 4Runner I did this to 5? years ago that had shredded turn signal harnesses in the front wheel wells is still like this and ripping all over New England. The radio too, if I recall.
@RobertNorton1
6 ай бұрын
I realized you said that in your video..after I rewatched it…
@01johny
6 ай бұрын
Great mod! Whereabouts are you guys located? Im trying to do this mod to my truck.
@Rockcreekgarageworks
6 ай бұрын
I am in Cali but moving to south Texas in a month.
@RobertNorton1
6 ай бұрын
The clips are on wrong…the lip of clip goes to the inside of the mirror opening
@Rockcreekgarageworks
6 ай бұрын
Clips? Are you talking about the black bracket?
@RobertNorton1
6 ай бұрын
Yes..the bracket…I just installed some….
@Rockcreekgarageworks
6 ай бұрын
@@RobertNorton1 the reason my right side is like that is bc they sent me 2 left brackets. They did send me the right one along with a new mirror for the one I broke.
@Zack-smith
6 ай бұрын
Black zip ties would work on top two clips also
@Rockcreekgarageworks
6 ай бұрын
Ya, I'll need to try that when I get back home.
@cmmoto
7 ай бұрын
Sounds like a fart
@Rockcreekgarageworks
7 ай бұрын
Ya, i thought the same thing. I was looking for a cattle horn at first. But buddy said he had this extra one, so I bought it.
@joepinto509
8 ай бұрын
The ones on there advertisement there running two horns...so it will sound different with one horn
@Rockcreekgarageworks
7 ай бұрын
Ya, I plan on ordering another one once I return to tx and try and get a better audio clip of them.
@lasvegasloks
8 ай бұрын
Hey brother what did you do with the black wire? Just cap it?
@Rockcreekgarageworks
8 ай бұрын
Sry for the late reply. I didn't get a notification. I unscrewed the black brace bar that sits on top of the battery that is connected to the fender. I put a u terminal on it and sandwiched between the fender, and that bar works fine.
@lasvegasloks
8 ай бұрын
@@Rockcreekgarageworks thank you bro i was confused but i ended up driving a small self tapper onto the metal bar that the radiator sits under with a ring terminal zip tied the wiring to that brace bar on top of the battery and it works perfectly fine, awesome video thank you for your reply boss
@Rockcreekgarageworks
8 ай бұрын
@lasvegasloks Thank you for watching, bro. I haven't uploaded anything new since the wife has the truck in TX, and I'm in Cali. But I will be in TX soon to continue making videos on the burbank and possibly a different build for the channel. I lived in Henderson from 16 to 19 next to GreenVally HS. Love Vegas so much. I was supposed to retire there, but Texas was cheaper and more land.
@lasvegasloks
8 ай бұрын
@@Rockcreekgarageworks right on bro ill be subscribing hopefully watch some more vids soon man, ive been in Vegas since 07’ love it so much this is my home i went to Clark HS and Rancho and now i bought a home in Centennial a long time goal for me, been all over ups and downs finally settled here in the north beers on me if youre ever back in town brotha
@Rockcreekgarageworks
8 ай бұрын
@@lasvegasloks hell ya sounds good love to see what ya done to ur build.
@Matt18.6
9 ай бұрын
Sounds nothing like a train horn.
@Rockcreekgarageworks
8 ай бұрын
Ya, I'm using my old Galaxy phone to record, so audio of the horn doesn't do it justice.
@licenseguru7025
9 ай бұрын
Does the sound diminish if you press longer on the switch? IOW, can the compressor maintain a constant sound? I bought two horns for my GMC 2500. Still on the fence about installing them.
@Rockcreekgarageworks
9 ай бұрын
it's like a mini compressor. It just keeps on going. I haven't seen a difference in the pitch dropping while I hold the button.
@licenseguru7025
9 ай бұрын
Thank you. Have you had a chance to add the second horn? @@Rockcreekgarageworks
@Rockcreekgarageworks
9 ай бұрын
@licenseguru7025 not yet, my wife has my truck in TX, and I am in Cali until I retire at the beginning of next year. That's why I haven't made the videos for the cab lights or the tow mirrors. I will order the 2nd horn once I'm home and do the install as suggested by another viewer and make a video.
@scottrobello
9 ай бұрын
Advertisement makes sound so much louder...kida a scam
@Rockcreekgarageworks
9 ай бұрын
All ads are a scam, but the price couldn't beat it.
@bluedeval03
2 ай бұрын
Difference of using one and they use two for ad
@jaygolden4218
9 ай бұрын
I guess for more sound you need multiple! There are no mounting instructions on the website. Is the horn as advertised? or are there better options out there? Thinking of putting one on my F 150
@Rockcreekgarageworks
9 ай бұрын
So it didn't come with instructions, that's why I just attached it to my horn. It does get people's attention because it isn't what they would expect when they try to cut you off. For mounting as long as you have a drill it can be put anywhere.
@jaygolden4218
9 ай бұрын
@@Rockcreekgarageworks I was reading when I live its against the law to have that loud of a horn on your car. :(
@Rockcreekgarageworks
9 ай бұрын
@jaygolden4218 There are some states that have specific regulations. The way I look at it is if you go to autozone, they have a section for upgraded horns. I don't know decibels but if they can sell them in the state why not get your own set.
@agustinsanchez7138
9 ай бұрын
Do they make one for a 2004 gmc Sierra
@Rockcreekgarageworks
9 ай бұрын
Yes they do
@agustinsanchez7138
9 ай бұрын
I can’t find one for a gmc by any chance do you know we’re or some a part number
@Rockcreekgarageworks
9 ай бұрын
@agustinsanchez7138 I'm sry it seems that the 04 was discontinued or out of stock. I was only able to find the 07 and up. You could use it with a front clip conversion, but it is cheaper to buy a mesh grill and add lights.
@BC-iz8gt
9 ай бұрын
Sound like a boat horn
@Rockcreekgarageworks
9 ай бұрын
Ya, I was thinking the same thing when I got it. I was looking for a cattle horn at first. Grandpa had one for the cows, and it reminded me of a tug boat.
@gmjunkyard3403
9 ай бұрын
The compressor should be mounted vertical and not horizontal...very important. Also the compressor should be powered straight from the battery with at least a 10 gauge wire and use a relay triggered by the factory horn wire. You will have a significantly louder sound. Your volume is affected greatly by these 2 factors.
@Rockcreekgarageworks
9 ай бұрын
Thank you for the info. I currently don't have the truck with me, but once I move back home I will make an updated video with the changes and compare the 2. Like I said I'm no expert so any advice I do appreciate it.
@EatLotsOfCurry
9 ай бұрын
I thought the sound was good for being one horn.
@Rockcreekgarageworks
9 ай бұрын
Thank you. I am going to try the other way and post a video and see how it changes.
@GLPMOVING
10 ай бұрын
It wasn’t that loud like they advertise
@Rockcreekgarageworks
9 ай бұрын
I'm not sure which model that was advertised. I bought mine off a friend and it's is loud enough to scare ppl and get their attention. I will say bc it's facing the passenger side, the sound is quiet on the driver side. Will have to add one facing that way!
@space_coast_snapshots6457
9 ай бұрын
No it wasnt
@MrGentlefriend
9 ай бұрын
I agree. Totally different sound. It should have sounded like the advertisement. I need not buy it now.
@paulcarrick3818
4 ай бұрын
The ads have multiple horns which give different tones
@stevenlynch6605
Ай бұрын
Why not use air horn with regular horns? Better sound
@Arkansas223
Жыл бұрын
How did you get the bumper together ? Mine came in 3 pieces & I can’t figure out what to use to get it mounted hood
@Arkansas223
Жыл бұрын
good*
@Rockcreekgarageworks
Жыл бұрын
If I remember correctly, there are screws that hold the 2 side pieces. There should be the metal clips that mount it to the radiator support.
@fredericdimas4098
Жыл бұрын
That gap hood to grill how bad?
@Rockcreekgarageworks
Жыл бұрын
Like factory
@Rockcreekgarageworks
Жыл бұрын
The gap you see is because I didn't close the hood. When it's closed, everything looks like normal.
@zachariahmagallan5738
Жыл бұрын
I'm trying to install a led kit on my 2000 chevy silverado does it matter witch fuse is on top and which is on bottom for the 5 and 10 amp
@Rockcreekgarageworks
Жыл бұрын
If you pulled the 10amp from its spot, then that should be what's on bottom. The pigtail wire is normal attached to the top slot.
@axellyman1947
Жыл бұрын
Looks great. I want to color match it haven't bought it yet, is it a paint able surface? Or is it plated or something weird? Should be able to do a skuff sand and then paint or no?
@Rockcreekgarageworks
Жыл бұрын
Yes, it is a normal plastic surface. You should be able to scuff and then paint it, and they sell a flat or gloss version when u buy it.
@axellyman1947
Жыл бұрын
@@Rockcreekgarageworks cool thanks
@sammybully5030
Жыл бұрын
what do you think about welding the seats on to the metal floor? or just bolts enough?
@Rockcreekgarageworks
Жыл бұрын
So I went with bolts because I want to be able to remove it when I need it. I am taking that risk with my passengers not having it welded. If you weld it directly to the floor, it would be safer. But you still need to raise it off the floor. There won't be too much leg room depending on who you have there. Also, you need about 1in of space for the wheels and clamps to sit below the clamping bar. There is a kit you can buy on Amazon or eBay for $60, and you can weld them directly to the floor, and then you would have a base to attach to. I'm no expert again. You're taking your own risk on doing this mod. I hit mine with a sledge several times, seeing if it would move or break and nothing, so I was OK with just using bolts.
@sammybully5030
Жыл бұрын
@@Rockcreekgarageworks yes I understand it is by no means legal nor may not be safe incase of an accident. But it sure soes serve a purpose esp if you have the esv/xl/suburban. any idea on the name of the ebay 60 dollar kit is called?
@Rockcreekgarageworks
Жыл бұрын
@sammy bully KUAFU 3rd Row Seat Brackets Compatible with 2000-2014 Chevy Chevrolet Tahoe GMC Yukon Style Split 3rd-Row Seats with Strikers and Bolts, Steel and Black Copy that and paste in Amazon. It is the same item on ebay, it is made for the Tahoe 3rd bucket seats but can be used for the 3rd row bench.
@sammybully5030
Жыл бұрын
@@Rockcreekgarageworks thx ur best
@Rockcreekgarageworks
Жыл бұрын
@sammy bully good luck with ur mod!
@z71overland05
Жыл бұрын
What size lift kit are you running?
@Rockcreekgarageworks
Жыл бұрын
6' fabteck with bilstein 5100
@kennethjakobsen4965
Жыл бұрын
Hi ! How do you enter the 4th seat row ?
@Rockcreekgarageworks
Жыл бұрын
The kids like to go through the back hatch or the back window mostly was fun for them. But it's the same as the 3rd row jump over the seat. I'm 5'10 and I can fit without shoes on in the 4th row.
@michaelrhoades9422
4 жыл бұрын
How are they doing
@Rockcreekgarageworks
9 ай бұрын
They held up really good until I traded truck. Sry late reply.
@x_nogame_50
4 жыл бұрын
do they fold automatic or no?
@Rockcreekgarageworks
9 ай бұрын
No, sry late reply
@michaelhorner7
6 жыл бұрын
What about mounting I just got some and the top is off and the two at the bottom are ok I too have a 99 k2500
@Rockcreekgarageworks
9 ай бұрын
Sry late viewing Easy done to put on and pull mirrors off.
Пікірлер