Thanks for taking the time to make this how to do video.After reading all the comments I decided it might be a wasting of time to change it due to the risks of other failing parts afterwards.
@td3428
3 ай бұрын
Worst washer ever. Had a cheapo Whirlpool that lasted 21 years. My Samsung front loader lasted 1 yr. Garbage product.
@matthewhardy8133
3 ай бұрын
Ours is 13 years old. 5 people in our house and lots of laundry. It just recently started making the bearing noise.
@willlamb3539
4 ай бұрын
This ain't even worth the time and effort lol
@misterfishguy
4 ай бұрын
Thanks for the video. I followed step-by-step and successfully replaced the bearings over the weekend. Took me about six hours total, but now the washer works like new! I don’t think I’d buy a front loader again.
@joseluislara3964
4 ай бұрын
What model of washing machine is it?
@DragonRider9
5 ай бұрын
Hello bro.. Can I connect illumination wire to ground?
@MarcSullivan-yo9gy
5 ай бұрын
"Bearing ... on ebay" - chances are you bought a counterfeit part. Same applies to Samsung. Considering how new the machine looks, I suspect they got scammed by their supplier (or the supplier's supplier) and installed a counterfeit bearing right in the factory as well.
@olegproscurchin8200
6 ай бұрын
Have bought same Samsung crap 1 year ago, right after the warranty expired I started to notice same noise 🥴. Thanks for the video 👍
@tarikulislam6759
6 ай бұрын
Bearing model please
@emildejong3169
6 ай бұрын
I bought these. Samsung Washer Seal Bearing Kit DC97-16151B DC62-00156A DC97-16509C Bearings
@cashew1392
4 ай бұрын
DC97-16509C comes up as the shaft assembly, not the 3rd bearing. Sigh😞
@Nicknoone1936
6 ай бұрын
Did any of your bearings have a snap ring
@emildejong3169
6 ай бұрын
I don't think so.
@salvatore_disano
7 ай бұрын
Great video but the link to the bearings on eBay you included no longer exists
@davidbooher278
8 ай бұрын
POS isn't worth the labor
@mikederedita7957
7 ай бұрын
damn pos bearings
@deebee3901
9 ай бұрын
Hi Emil, it the washing machine still running well with its new bearings? An update now that it has been 12 months would be most useful. Cheers from Australia!
@emildejong3169
9 ай бұрын
Hi Dee Bee, in full transparency no. While it works and the bearings are quiet, it has developed a balance issue which could likely be from me not being patient and careful enough when hammering out the original bearings.
Thanks for the video, very helpful. Do you know what the bearing sizes were? I assume Samsung are using cheap bearings, I'd prefer to replace with a premium brand if i can!
@emildejong3169
Жыл бұрын
I bought these. Samsung Washer Seal Bearing Kit DC97-16151B DC62-00156A DC97-16509C Bearings
@productionapostle1298
Жыл бұрын
Good video bro.. very detailed 👌
@Unplugged704
Жыл бұрын
I have the same noise PLUS banging noises during the spin. I think this banging may be due to bad shocks. Our Samsung FL washer cost $600+. Buy new is probably about the same cost $$$ to hire pros to fix both problems. I’ve watched a few how-to videos on the fixes. Still debating if I should or not! One video I saw was labor intensive to get to the bearings 🤷♂️🤷♂️🙁🙁. Makes me not want to do it. Seeing yours isn’t that bad to do on my own 🤔🤔😁😁 -*** I noticed you did not grease the outer bearing before you banged it in, but you applied it after. Was it hard to bang in?
@emildejong3169
Жыл бұрын
The bearing was difficult to bang in. I recommend greasing it. I may have done that off camera but I can't recall. The biggest thing to remember is that you need to be patient. If you bang in the bearing too impatiently and hard you risk impacting the balance of the entire drum assembly.
@brandonfamily4594
Жыл бұрын
Saved me a ton of time and prevented breaking that clip. Thank you!
@NickMualim
Жыл бұрын
Thanks for the video! it helped me see how complex it is to replace this part and I will be calling a technician 🙂
@stephanieslover-mc6zd
Жыл бұрын
I've got this and thing going on with a washer I bought BRAND NEW 2 years ago😡
@radiohead2206
Жыл бұрын
Great video thank you. Does the inner bearing have a marker to know when to stop ?
@X_PATHOGEN_X
Жыл бұрын
Yes
@peterdong4347
Жыл бұрын
Thanks for the video, it was extremely helpful for when I replaced the counterweight and front tub in mine. Note - for the heating element wires (4:08) you could leave the wires and just pull the heating element out. Just loosen the middle nut, and remember to tighten when putting back.
@robchiste3638
Жыл бұрын
What was that piece of metal just under the seal that you flicked away? Does it go back or was that part of the original seal? Asking because mine was the same way.
@emildejong3169
Жыл бұрын
This is part of the original seal and needs to be reinstalled after. It's just a spring loaded metal ring.
@robchiste3638
Жыл бұрын
@@emildejong3169 thank you
@CancerInsights
Жыл бұрын
Great job and thanks for sharing! A couple of questions, I have a similar noise when in the highest spin setting otherwise the noise is normal. Did yours make noise at the low spin? How do you find out it was the bearing defect? Would you post the bearing part number so I can do a search?
@emildejong3169
Жыл бұрын
It was mostly on high spin although it got worse overtime. If it starts getting worse I would say it's your bearing. I was never 100% confident that it was the bearings but it apparently was and the noise went away once changed.
@blakebremer3348
Жыл бұрын
Thanks for the video, very helpful!
@begformeowcy
2 жыл бұрын
I’ve installed my stereo but my antenna is always up even when I’m not listening to the radio, is there a way to get it to go down when I’m not listening to the radio? It retracts when the stereo is off. But it’s annoying how it up all the time when the car is on :( wondering if I stuffed something up.
@nagrajswamy326
3 жыл бұрын
Hi Sir My Sony 5000 when reverse camera show as no video signal But before it was working fine What would be issues please help me
@emildejong3169
3 жыл бұрын
I am not sure. I actually never used the cameras feature. If it was previously working and your wiring hasn't changed you could have a bad camera. Or maybe try resetting the Sonny head unit? Sorry I couldn't be much help.
@nagrajswamy326
3 жыл бұрын
@@emildejong3169 thanks for your support
@mediapc4747
3 жыл бұрын
Never seen anyone tape the wires together for the speakers on the unit's multiway connector...that's shorting an amplified output isn't it!? The RCA's are unamplified (just 5v)
@skillsdevelopmentformainte6815
3 жыл бұрын
where can I buy the valves?
@rudawabdulrahman1010
3 ай бұрын
3/4 Inch Electric Control Water Valve Copper DN20, Electric Water Flow Adjusting Valve...
@skillsdevelopmentformainte6815
3 жыл бұрын
Where can I buy the valve control?
@giancarlofranchini3853
3 жыл бұрын
You are an absolute legend. Thank you for the help!
@ginomatheismatthews5915
3 жыл бұрын
How are you running the steering wheel control to that radio
@emildejong3169
3 жыл бұрын
You will need to purchase and adapter of you want the steering wheel control.
@abigailborden
3 жыл бұрын
What about the USB1 and USB2? I know to do a firmware update both ports are required. What do you know about the USB ports?
@emildejong3169
3 жыл бұрын
I don't know anything other than one is used for data such as music (updates I believe) and the other is for Android Auto/Apple carplay.
@caleskenasy275
3 жыл бұрын
Funny you say the parking brake wire should be connected to the parking brake directly. There's a specific red/white wire which the parking brake wire connects to: it's one of the benefits of the PAC set: you don't have to dig down.
@3DnGin
4 жыл бұрын
What about the purple / wht striped "Reverse In" wire? What do I connect that to?
@justinsheffield2807
3 жыл бұрын
I know this is an old post but did you ever figure out?
@bleebleblahble8833
3 жыл бұрын
Reverse shifter light wire?
@mediapc4747
3 жыл бұрын
Reversing lights
@jeffflowers729
4 жыл бұрын
I just got the ax 5000. it doesn't have dvd so what function would i be missing by not using the green brake wire at all?
@emildejong3169
4 жыл бұрын
I think the only functionality lost was with apple car play and android Auto. I know android Auto wouldn't let you accept permissions if you had a new device or something work the brake off. That's pretty much it. Also, an update since knows when you are moving and not moving so it no longer makes as my difference. I would simply install is the easiest way.
@jeffflowers729
4 жыл бұрын
@@emildejong3169 I attached it directly to the radio chassis and everything seems to be working.
@kf4736
4 жыл бұрын
So will grounding the brake work or does it need a switch?
@kf4736
3 жыл бұрын
@@trentc.1120 It works, had it since June, system is mint
@jpatton412
4 жыл бұрын
So, I know this is old thread, but did you plug the 3.5mm for the SWC into the blue "Remote" on the back of the AX5000?
@emildejong3169
4 жыл бұрын
I am note sure what you mean by remote but if I remember correctly it plugged directly into a blue colored headphone jack on the back of unit. Hope this helps.
@mohsennikbakht2425
4 жыл бұрын
hi, thanks for sharing this with us. could you please help me with the valve connection to Arduino and also the code.
@akillaxman2155
5 жыл бұрын
Does the steering wheel voice control button work as well with the ax5000 ? I have a Honda City/ Grace for which I plan to buy this unit.
@emildejong3169
5 жыл бұрын
On my 2011 Mazda 3 it does. It will trigger Google Assistant or Siri depending on if you use iPhone or Android.
@akillaxman2155
5 жыл бұрын
Thanks a tonne for the quick reply ! This helps !
@JuanyJuanes
5 жыл бұрын
Bro you’re a lifesaver
@marcounchained
5 жыл бұрын
Hi emelio great video you helped me with my Mazda 2011. Got a quick question. What was the reason you grounded the parking wire?
@emildejong3169
5 жыл бұрын
Glad to hear it! I grounded the parking wire so I can have full functionality of the head unit without having the break on.
@emildejong3169
5 жыл бұрын
Also it was easier for me since I didn't need to open up my parking break.
@marcounchained
5 жыл бұрын
Emil De Jong sounds the unit will be disabled when the parking brake is not activated. Also I have no idea how to wire the parking wire to my parking brake. I will install my radio unit today! I will let you know the results
@marcounchained
5 жыл бұрын
Emil De Jong one last question. What about the reverse wire?
@emildejong3169
5 жыл бұрын
@@marcounchained I didn't buy a reverse camera so I just taped it and left it not connected
@yasirshahzad3732
5 жыл бұрын
From where did you get the valve?
@niksyimi
5 жыл бұрын
Hi bro do you mind to send some link or the exact name for the steering controller adapter that you used? Anyway I'm using Mazda 3 2012
@emildejong3169
5 жыл бұрын
I used the PAC RP4-MZ11 Wiring Interface. You would need the MZ12 if you have a 2012.
@alvetica1
5 жыл бұрын
Thanks!
@asupermodel
5 жыл бұрын
Is it possible to wire in your steering wheel controls without an interface?
@emildejong3169
5 жыл бұрын
That is a great question and unfortunately one that I do not have an answer to. All I know is that steering wheel interface communicates by sending different voltages to the Head unit.
@asupermodel
5 жыл бұрын
@@emildejong3169 thanks for the reply. That is to bad. I ordered the unit on amazon and am still waiting for the dashkit to come. Putting this into my 05 f350. I havent ordered an interface but guess i will do that to make life a little easier.
@tonysfun
5 жыл бұрын
I wish you have the Arduino sketch and what sensor you used and wiring! Can you please upload that here and or make a video and let all of us know how to use this sensor? I just digged one out and I would like to play with it and Arduino. Thanks!
@khalid0790
5 жыл бұрын
Thanks that will help ‘3 big time, I’m installing the same unit in 2015 Mazda 6 with Bose system. Any wiring tips or recommendation to make my installation Smooth would really appreciate it 👍🏻
@emildejong3169
5 жыл бұрын
My only tip is that you get Boss compatible wiring harness. I know that having the boss system requires different equipment.
@khalid0790
5 жыл бұрын
Emil De Jong they recommended the same adapter for me too, does your backup camera still works when you put your car in reverse ?
@emildejong3169
5 жыл бұрын
@@khalid0790 I don't have a back up camera but your harness should have 2 clearly marked wires that indicate reverse camera.
@edisonbonilla781
4 жыл бұрын
Emil De Jong what can I do if my usb 1 and 2 are cut off ?
Пікірлер