Hey, the rod got pushed further than what you had on your video. Is that fine?
@visolejah
2 ай бұрын
Thank you. You saved me $3,900.00 in repairs. You will need grease if you do it alone. Mt son and I knocked this out in about an hour, great video!
@BradleyMcClelland
2 ай бұрын
Did the transfer actuator work as per normal after the reset to two wheel drive
@timst5055
2 ай бұрын
Yes, switches from 2-4-LO without any issues
@edwardmcdermott9948
7 ай бұрын
you probably should have done a zero.point.recalibration any time work is done on the vehicle
@gerryboisvert4434
7 ай бұрын
thanks great video
@zahidhussain-hy1xy
7 ай бұрын
Thanks my friend very very nice video thank u
@rincewindmacgyver1852
8 ай бұрын
Saved my ass today at work thanks bro gr8 explanation
@tariqsaee2256
9 ай бұрын
Thanks man you’re life saver
@moshet842
9 ай бұрын
So much for reliable. These cars really suck when they do.
@kennedywiller2961
10 ай бұрын
how do i bleed the brakes ? 😅
@rangerrick7831
10 ай бұрын
On my 2016 trd sport, Transfer case oil is getting into the actuator box. Is this normal? Is the small tube to let oil in or out?
@moustaphacheva3757
10 ай бұрын
Hi . Do you get the same code that i got ?? P17A0 😊
@makofive.5660
10 ай бұрын
The fact that anyone has to go through this on their 4WD system is ridiculous.
@HarleyMikeJrSWA737
3 ай бұрын
Be happy it’s not buried inside the transfer case
@chrislee4946
11 ай бұрын
Great video! Thank you
@reprisal1051
11 ай бұрын
I have second gen tundra and I’m buying a new transfer case, but it doesn’t come with the shift motor. Can that rod be pulled out and put in the new transfer case without taking the whole unit apart?
@reprisal1051
11 ай бұрын
I have second gen tundra and I’m buying a new transfer case, but it doesn’t come with the shift motor. Can that rod be pulled out and put in the new transfer case without taking the whole unit apart?
@Stevespecs
Жыл бұрын
2004 4 runner , I engage 2wd to 4 wd hi and to low every month, from day one. So far so good. Time will tell. Great information
@michaelvachon1334
Жыл бұрын
Well done! Only comment I would make/suggest would be to clean the reservoir and use new brake fluid before assembling. Like the fact that you included priming the master cylinder before re-installing. I got bit by this - but just once!
@callsignmohas5190
Жыл бұрын
Yeah, but didn’t you just put contaminated fluid into a new master cylinder? I thought anytime you were changing a cylinder you had to use fresh fluid to eliminate any prior contamination.
@MrBULLRIDER13
Жыл бұрын
Question is this the same setup as say an 04 Toyota 4runner 4.7l v8. Cause i think my wifes was failing for a long time it sucked in snow then it could only move in 4 low. Then i tried to move it to my project pile but it wouldn't move at all says its in 4low with diff lock on but won't move at all and sometimes grinds id you try to put it in gear. I had this cover off the transfer case actuator but i had no red gear just those other three gears. I tried to take them off and remove the actuator but it wouldn't budge even gently with a pry bar.
@useryggfdcc
Жыл бұрын
Always check if the breather line is properly attached to the actuator. If not water get inside and corrode the contacts....giving solid or intermittent problems.
@chrislee4946
11 ай бұрын
what type of issues would this cause? i checked my breather tube and noticed it had split and was coming undone so i snipped that piece off and pressed it back on
@useryggfdcc
11 ай бұрын
@@chrislee4946 The front actuator was replaced on my Taco 3 weeks ago. Working good now. It was a warranty job by Toyota dealership so I couldn't get the part to inspect myself. It's very important to regularly activate the 4L and 4H. Its even recommended in the owner manual.
@CherryBlawesome
Жыл бұрын
I hope this method works for a 2006 Ram. Man, I hate dealerships so much; highway robbery! This is so easy. I’m a lady and confident I can to do this myself. *hair flip* Thank you for the detailed instructions!😁😎👍
@AlaskanGoldMiner
Жыл бұрын
Well I’m in the stealership right now with the same problem. Only 16,000 on the truck so luckily still under warranty. I snuck back into the service bay to have a look and they had the entire transfer case on the floor. The service tech says it’s a bad actuator, but I can’t understand the need to drop the entire transfer case!!
@johnwoodrow8769
Жыл бұрын
To fit a completely new actuator (box and rod) the transfer case must be removed, which likely means the complete transmission. Then the transfer case must be partly dissembled to remover the various internal clips and positional ball/springs that hold the actuator rod inside the transfer case. You will find an Aisin KZitem of the complete procedure, which clearly shows why they do it that way.
@G.host3d
Жыл бұрын
FUUUUUCK, I skipped to 1:17 and was watching super chill following along....Then all of a sudden you're taking the actuator off with both hands and pointing with your third hand .....trippy af.
@timst5055
Жыл бұрын
Haha, I hope the video helped!
@yamilethmojica5779
Жыл бұрын
One of the most helpful video thanks!
@ifulpublik4680
Жыл бұрын
Teks nya gak ada ya?.... Sangat bermanfaat🙏👍
@brianw8963
Жыл бұрын
Was having similar issues with my 19 taco(6sp manual) with only 11K, as can be seen in a couple prior recent comments. Here is a CRAZY update which I have absolutely no explanation for. As I’ve mentioned,I removed , inspected, lubed and reinstalled the actuator. It worked a few times but went right back to either not going into 4l, or if it does it won’t come out. TRY THIS! FULLY DEPRESS AND RELEASE THE CLUTCH PEDAL 2 TIMES. As you are releasing the pedal the second time, it will click in(or out) I could not believe this when I was told by my local Toyota shop manager. He has no explanation and just found this out. I immediately thought BS, but happy I did not flip out on him . I tried it and it works perfectly every time going into and coming out of 4 low. Sorry I do not know what to tell the owners of automatics.
@timst5055
Жыл бұрын
Thanks for posting this!
@brianw8963
Жыл бұрын
@@timst5055 👍
@brianw8963
Жыл бұрын
Thank You for this Tim. Been having this same issue with my 19 sport (3 pedal) with only 11k. The Toyota procedure for replacing the actuator involves removing and splitting the case. Why? Absolutely no reason I can see. Everything inside the case gets plenty of lubricant and the “sticking” issue is not inside that I can see . Though You fixed the immediate problem, I would like to figure out “what” is causing it? I’ve seen some that actually have to bump the shift shaft in with a hammer(rubber mallet) to get it freed up. So I’m thinking gob a generous amount of maybe some of that white lithium type grease in the area where it goes through the case from the actuator side . Gonna give it a try today and see what happens. Nothing to lose. And thanks again.
@timst5055
Жыл бұрын
Glad I could help. Not sure what causes it either, let us know if greasing everything up helps. Thanks!
@brianw8963
Жыл бұрын
@@timst5055 Well, it was worth a try, but is definitely not a lubrication issue. Where the shaft passes through the housing, there is actually a notch that allows for oiling and is sealed on the outer side. I could not see that in the video but was very apparent when I got into it. I lubed up all the plastic liberally with white lithium grease, put it all back together and it worked great, for about 6-8 cycles. Then it returned to the same problem. It either won’t go in to 4L, or it goes in and won’t come out. So I’m calling it a Toyota actuator problem that they need to address. It takes a good bit of energy to move that selector shaft and I don’t think the plastic components and possibly the motor are up to the task. Toyota needs to step up on this issue. Thank You! 👍👍🇺🇸
@atashadono2852
Жыл бұрын
nice video
@johngallagher8626
Жыл бұрын
Thanks much for taking the time and effort to do this video! It is 10 degrees here now and I was stuck in low range. 2017 Tacoma standard. I searched quite awhile for info on resolving this issue. Your video is the only one that explains exactly what must be done. I down loaded the factory service manual and it was no help. I am 74 and well experienced in working on all sorts of mechanical devices, having worked professionally as a motorcycle mechanic for 15 years, still working on cars, trucks and tractors, and motorcycles! You definitely saved me on this cold day working in an unheated garage, snowing blowing outside. Feeding cattle a round bale earlier this morning on my cab less tractor was cold with the wind chill. It is quite amazing what can be found on the internet, done by people like you! thanks!
@timst5055
Жыл бұрын
I’m glad I could help!
@brianw8963
Жыл бұрын
John, Did You happen to catch what I posted about fully depressing and releasing the clutch 2 times? Try it and let me know !
@alfredallen4687
Жыл бұрын
Good job explaining the process. I was able to understand the whole video and I'm no mechanic.
@timst5055
Жыл бұрын
Glad I could help!
@ericochoa4271
Жыл бұрын
My 2022 gets stuck in 4H
@chojthoj08
Жыл бұрын
Did u used new parts or same parts, just relocating?
@timst5055
Жыл бұрын
I just used the same parts I had. Double checked that all the gears were complete and no teeth were missing.
@chojthoj08
Жыл бұрын
@Tim St I put in a new one, but I still can't get in 4 low. Just keeps flashing. I have to turn off truck and put it back to 2wheel. Any clue???
@timst5055
Жыл бұрын
Are you sure the gears are in the correct timing slot? If it’s slightly off it’ll keep flashing and not working.
@chojthoj08
Жыл бұрын
@Tim St yea all gears ⚙️ are line up. First time I can't get into 4 low. Now I can't even drive if it's on 4 high. Solid green light but can't drive, but I am able to put in 2wd easily... then it drives. Will do it again tomorrow..
@JimsEquipmentShed
Жыл бұрын
Yea, when ours goes, I'm bypassing with a lever through the floor........
@007lakay
Жыл бұрын
I just opened the actuator on my 2008 4Runner, the 2 big gears fell off and can't figure out how to put back in. I randomly put the gear back and now the 4WD lights is always ON blinking no matter how I turn the selector switch. This video will definitely help me with the timing. Will open the actuator again tomorrow. Thanks a lot.
@timst5055
Жыл бұрын
Good luck, let us know how it goes!
@007lakay
Жыл бұрын
@@timst5055 Follow up question: Should the rod freely goes in and out when the transmission gear is in neutral?
@YomAlwa3eed
Жыл бұрын
@@007lakay no it wont go that loose even on N
@JorgeGonzalez-lk6yl
Жыл бұрын
Where you able to drive under 60mph in 4H?
@timst5055
Жыл бұрын
Yes
@markviray1527
Жыл бұрын
Hey so I'm having issues with my 2022 Tacoma. When I switch it to 4hi it engages but the light keeps blinking. Do u think this will fix issues?
@timst5055
Жыл бұрын
Once you switch to 4wd, can you switch back to 2wd?
@garywinkel1831
Жыл бұрын
Now, put some gas in that damned thing and get your TPMS sensors replaced, LOL.
@timst5055
Жыл бұрын
Waiting for the lights to burn out, so I’m not reminded anymore! Haha
@garywinkel1831
Жыл бұрын
Also, notice how the vent hose is split a little on the end. This is the failure of a lot of these units. The hose splits over time and falls off, then water gets into the unit. This would be a good time to snip a little off the end of the hose before reinstalling. I've done this once on my truck as a preventive measure since it was split, but not to the point of failure. It looks like on the 3rd gens, they left the vent hose plenty long to accommodate this. Check your ADD actuator and rear diff locker for this as well, if your truck is equipped with them. Great video!
@Danny52093
Жыл бұрын
Very informative video
@TimmyTheToolman
Жыл бұрын
I'm curious, where did you learn the information regarding the correct timing for the gears? Do you have a source to share? I looked up factory service manual information from the Toyota Tech Info website and did see anything about taking apart the actuator.
@timst5055
Жыл бұрын
I looked through every manual, asked multiple Toyota dealerships, tried looking online and couldn’t find anything. Then came the trial and errors. Eventually, I purchased a new one and carefully took it apart and saw how it was positioned at the factory. Put it in the same way and it works.
@TimmyTheToolman
Жыл бұрын
@@timst5055 I appreciate you getting back to me. I applaud your dedication to getting the answer you were looking for. I might be helping a guy figure out an actuator issue on his Lexus GX470 soon and your video will be listed as a reference if I make a video of the job. Thanks!
@timst5055
Жыл бұрын
Glad I could help. Good luck!
@TimmyTheToolman
Жыл бұрын
@@timst5055 Thanks Tim!
@ARbassfishing13
Жыл бұрын
Do you happen to have a picture pf the timing on the gears of the new factory one? My truck is not timed correctly and it’s frustrating
@eternalklothgardengangsta685
Жыл бұрын
Dealership wanted $1,000 Think ima do it myself now. Thanks
@winds10
Жыл бұрын
Thanks, man. I'm going to try this on my 4th gen 4Runner. Wish me luck!
@YomAlwa3eed
Жыл бұрын
how did it go?
@ryanhensley146
Жыл бұрын
Just put in reverse and slowly back up and should unlock out of 4Lo
@leandromedina6805
Жыл бұрын
my truck doesn't have any leaks and my brake boot is new and my pedal keeps going to the floor. what do you think it could be?
@iblongshia
Жыл бұрын
Check all your bleeders and make sure they are tight.
@1995dresser
Жыл бұрын
Very nice video my 2005 Tacoma was always a little touchy going into 4W LO and once I had a difficult time getting it out of that mode and almost had to park it and possibly have it towed I always tried to at least cycle the 4WD once a month to keep everything moving inside the actuators both on the transfer case and front differential but now all I have is 4W HI and there are times when I could use LO because my truck has the 2.7 4cyl and 5 speed not much in the Horsepower department lol
@jasongoode133
Жыл бұрын
My 2016 was stuck in 4lo I did what you showed its back in 2wd now but when I try to shift in 4wd it only blinks do u think my actuator is bad?
@timst5055
Жыл бұрын
Either your actuator is bad or your actuator skipped timing. Try following my video and resetting the timing before buying a new actuator. If that doesn’t help you might need a new actuator.
@jscons7424
Жыл бұрын
Thanks for the video, it helped
@jacobmees8040
2 жыл бұрын
Nice video, just one small correction though. The transfer case only switches between high and low, and the front diff switches 2wd and 4wd. So, basically putting the tcase back into high, which fixed it.
Пікірлер