Good luck with finding a cartridge if you need to replace it. Definitely not recommend it.
@uy-scutipacific6398
Жыл бұрын
Lil hoes Here hahahahaha😊
@rudolphblair8577
Жыл бұрын
Since the hand held part is short after you finish the tiles, what did you use to extend it?
@bdyt
Жыл бұрын
The mixing valve seems to be a very generic cartridge used in like vanity and kitchen faucets. Is it pressure balancing? Are there shut offs in the valve body when you need to replace the cartridge? I think that's why these set ups are so cheap.
@nmieles2012
2 жыл бұрын
hi, I have a hot water pressure issue I changed the mix water valve and still the same
@kchilz32
3 күн бұрын
What was the cartridge part number
@darwinbodero7872
2 жыл бұрын
Guys. Don’t buy this or any model that looks like it. Theyre all made by a few manufacturers in China. Don’t install this behind your wall. I took one apart and the quality is garbage. They are cheaply cast with debris from the mold inside. The threads are not cut well and with sharp chipped areas near the o-rings.
@juanluna2493
2 жыл бұрын
Easy to install, then on trim I had to run around town looking for parts to make it work, looks nice but it’s not worth it.
@AtypicalPaul
3 жыл бұрын
I installed one and wand doesn't work. No idea why
@MrMarioariasjr
3 жыл бұрын
How do you adjust the scalding level? I can’t get hot water through
@jasonrobinson9242
3 жыл бұрын
My client bought one also,i installed it the water wont get hot
@AtypicalPaul
3 жыл бұрын
@@jasonrobinson9242 same here no hot water
@jasonrobinson9242
3 жыл бұрын
@@AtypicalPaul i replaced the cartridge with a new one and it fixed all my problems!
@kchilz32
2 жыл бұрын
@@jasonrobinson9242 where did you get the cartridge? Link?
@kchilz32
3 күн бұрын
@@jasonrobinson9242what is the cartridge part number? Where you get it?
@markwaugh2613
3 жыл бұрын
I just put one of these in and I put shower head and sprayer female fittings 7/8 out wall for tile I hope this works out.
@TheMemo1776
2 жыл бұрын
7/8 for tiles and drywall?
@angelvelasco9770
Жыл бұрын
@@TheMemo1776 tile and 1/2” rockin board
@johnal4560
3 жыл бұрын
is it a good shower kit any leakage or any other issues by now
@mirelurk-fish7387
3 жыл бұрын
I installed 3 of these on my property that I rent out and one week later two of them are leaking pretty bad now... I would not recommend
@LVCID777
3 жыл бұрын
Where are they leaking?
@mirelurk-fish7387
3 жыл бұрын
@@LVCID777 the diverter area
@DR-um2bv
Жыл бұрын
Enough said, removing from Amazon cart.
@tamergomaa
3 жыл бұрын
اولاد #جمعه للادوات #الصحيه بيع #تركيب #صيانه عمل #نافورات المياه تاسيس #المزارع عزل #الحمامات و#المطابخ و#الاسطح #للتواصل 01200258817 #المحله الكبرى #بلقينا
@krawlly8643
3 жыл бұрын
How do you remove the cartridge to change water temp?
@JSIBachata
3 жыл бұрын
Did you ever find this answer? I'm having the same issue
@jasonrobinson9242
3 жыл бұрын
@@JSIBachata u can un screw it and there is a cartridge available
@bobbymeyer6493
2 жыл бұрын
@@jasonrobinson9242 there is a different cartridge?
@jasonrobinson9242
2 жыл бұрын
@@bobbymeyer6493 yes it was made by Gerber. They specialize in replacement cartridges
@bobbymeyer6493
2 жыл бұрын
@@jasonrobinson9242 is there a way to adjust cartridge I just had a Boyel living shower head installed today. It looks like the same valve and it will not get hot
@SamariumNickel
4 жыл бұрын
Do we know what cartage these take and if we can get them to replace it later? I have the 3 way valve version
@darwinbodero7872
2 жыл бұрын
I took mine apart and theyre generic. The diverter stem can be taken apart and o-rings replaced. I found what appears to be a 35mm cart made by yaoli. You can find them on Amazon. I found the quality of these things to be absolute garbage though. Don’t think I’ll be putting one behind the wall
@lorenzovienna934
4 жыл бұрын
Same problem handel isn't fully screwing on for the hand shower is there a fix or peace for this to tighten on just spins the treads
@seandean6461
4 жыл бұрын
Now that some time has passed, would you still recommend it?
@bradwerenka6843
3 жыл бұрын
I’d like to know the same. How is it working now? Still ok?
@DR-um2bv
Жыл бұрын
Oh, ain't no telling. Literally. We're all on our own
@auadventuresunknown7611
4 жыл бұрын
Hi Matt. Thank you for showing the video. I watched yours before I installed mine. Since then I am having a trouble installing the handheld shower holder itself. It's not exactly like yours. Mine is by Oleah, which I picked it up from Amazon. The brass core turns as you can see from a VDO below. If it turns, how can I make it tight? If not tight, of course, water will leak. Please see a video and snapshots below. kzitem.info/news/bejne/0Xyc3ZmkaWWQrZw kimook.com/Holder/11.jpg kimook.com/Holder/22.jpg kimook.com/Holder/33.jpg kimook.com/Holder/44.jpg Are there any parts missing? The female 1/2-inch copper which I bought it at Home Depot. Guys, I need help. Thank you, and happy holidays.
@allenuic
4 жыл бұрын
Hey Brian, did you find a solution to the loose brass fitting on the shower bracket? I'm actually dealing with the same issue. That was a very poor design.
@lorenzovienna934
4 жыл бұрын
Having same issue handle just turns leaks out of it what was the fix.?
@gl1125
4 жыл бұрын
@@lorenzovienna934 did you leave the drop ear too far into the wall? you should have the drop ear screw only a little recessed (0.22mm) from the outside tile/finish.
@SamariumNickel
4 жыл бұрын
The threads on my handheld shower holder aren't done well. I can't get it to screw into the 1/2" pipe fitting past 2 threads. Do we know if that brass fitting is replaceable at all? A 1/2" male / male connector from home depot threaded fine in the wall fitting but doesn't fit the holder.
@tecmolog
4 жыл бұрын
Thank you for your detailed introduction, it helped me a lot. More information: tecmolog.com/bb314b-p0051.html
Пікірлер