I’ve just used this technique on my Fiat Ducato so thanks for the tip 👍 Some come out easier than others and my extra tips would be to wear gloves as if the screwdrivers slip into your hand it’s going to hurt. Also use as big a flat head screwdrivers as possible as this helps with the aforementioned slippage 👍
@UniqueTint
9 ай бұрын
Great tip!
@TRUCKERJOES
Жыл бұрын
Hahah😂 like owner, like dog! 😅😂😂😂
@onyxnorbert
Жыл бұрын
Hi , those clips they fit up&dow ? Or just dows thanks
@UniqueTint
Жыл бұрын
They will fit all up and down.
@DriftfishCo
Жыл бұрын
Should I apply sealant first before refitting? We have a campervan so I don't want water inside. Thanks again.
@UniqueTint
Жыл бұрын
Hi If you have straight panels and clips have rubber seal that should be enough but on other hand silicone would also help. I would apply that as well if it was mine. Thank you for watching my video.
@DriftfishCo
Жыл бұрын
@@UniqueTint thanks Slav, could you please help with my other question below 🙏.
@DriftfishCo
Жыл бұрын
Hi, to put the moulding back on do you put the clips in the moulding and then offer up to the van or is it the other way around (clips in the van and then push the moulding on). Thanks
@UniqueTint
Жыл бұрын
Sorry I didn't reply before. You need to fit clips on to moulding then push back in position. If you intend to use sealant you need put on a body then push panel to it.
@johnloftus4285
Жыл бұрын
Thank you so hard to put down on now iv bort new clips
@sajardine4403
2 жыл бұрын
how to replace panel...clips I have appear too short to stay in - advice appreciated
@UniqueTint
2 жыл бұрын
Is it the last one on rear side panel? Sometimes when van was repaired the last one doesn't sit properly. If this is your case you need to bond it with something strong. If you would like permanent fix use windscreen bond but prime both areas correctly.
@tuomasholo
3 жыл бұрын
This was very helpful
@UniqueTint
3 жыл бұрын
Thank you
@actioncomet
3 жыл бұрын
thanks saved me breaking all of them
@UniqueTint
3 жыл бұрын
You are welcome. That is what we are here for to help each other.
@longbar2344
3 жыл бұрын
so how do you remove the actual moulding? slide it?
@UniqueTint
3 жыл бұрын
You would have to rip it off as the clips facing opposite way. Many if them will be broken that's why you need spares. If you pull to about half way then you could possibly slide. I hope this helps.
@longbar2344
3 жыл бұрын
@@UniqueTint i found one on ebay and made that discovery. bit shite
@samuraiJDM96
3 жыл бұрын
Здравствуйте! Отличный канал 👍буду рад взаимной подписке ✌️
@UniqueTint
4 жыл бұрын
Yes 1.9tdi. Car sold and not here anymore. New owners destroyed it.
@HardyJeffMC
2 жыл бұрын
very sad
@UniqueTint
9 жыл бұрын
We can do it without removing door panels or trims but that's not pros...
@teeduck
9 жыл бұрын
The pros do it without removing door panels or window seals.
Пікірлер