Q..what type scan tool are u using to retrieve code.Brand.Ty
@Drootb
17 күн бұрын
This is the video I’ve been looking for forever. Thank you so much
@bgfixit
17 күн бұрын
Glad it was helpful!
@earlyhemibill
18 күн бұрын
Followed your lead and it woeked. Thank you.
@topcat1tanks
Ай бұрын
What is the torque measurement on the frame bolts?
@bgfixit
Ай бұрын
Sorry, I don't have any vehicle-specific torque values for the Kia. You can find generic charts for metric bolts online though
@carlosandres8974
2 ай бұрын
hey im thinking about a harmonic pully replacement for my 2005 nissan altima because it wobbles very bad some people say its because it has to much tension but im not sure if that is the issue i fear maybe the pully is bent so i will be trying to replace it instead
@carlosvega4967
2 ай бұрын
Just what I need to know is a great example without watching 10 minutes of video
@markbrown9578
2 ай бұрын
It works now tell me how to get my windows to have power
@FoxFaderWorld
5 ай бұрын
Good vid, but press down on the connector's clup then pull it off the sensor.
@chrise3265
6 ай бұрын
They had a 10 amp in mine for some reason. I switched it to a new 5 amp and it still has this issue 😢
@DBsFabShop
6 ай бұрын
Back of the fuse block probably got cooked because the fuse was to high amperage to blow
@DBsFabShop
6 ай бұрын
Same thing happened to me 😢
@chapo5728
6 ай бұрын
Same here man I heard the ding but no windows or dome
@RazsterTW
7 ай бұрын
That fixed it! Removed the 4th fuse in the second row and my dome, wipers, water wash all worked. Thank you!
@bgfixit
17 күн бұрын
Glad it helped!
@dukeyhird5604
8 ай бұрын
"promo sm" 😡
@juliocesarnolascoislas4948
9 ай бұрын
Excelente video mil gracias por su aporte ésto fue como magia
@arrownetworking
9 ай бұрын
This fixed my problem. Thanks so much for uploading the video.
@bgfixit
9 ай бұрын
I'm really glad it helped! That's why I do these. Thank you for watching!
@Badassbass79
11 ай бұрын
I changed my syncronizer and sensor on my truck afew days ago.done everything u saud. But still on limp mode and says 340 on scanner.but the 2106 will pop on to but then i do it again it wobr show up only code 340.can u help me please???
@curtkellison3429
Жыл бұрын
What if ur sensor doesn't lift right up and off
@curtkellison3429
Жыл бұрын
Nevermind i found out why it was cracked and corroded inside
@shawn011274
Жыл бұрын
Do you have to put cylinder 1 in TDC, before engaging tool?
@dealerhealer3673
Жыл бұрын
Thank you very much sir
@rogerblair8133
Жыл бұрын
Finally I found somebody to explain this in lame terms where I could understand it . I did the same thing pulled it out without marking it and I didn't paint my engine so I was lost until I seen your video. Thank u
@coreybabcock2023
Жыл бұрын
Yea I used the shape and curvature of the pigtail going to the sensor
@coreybabcock2023
Жыл бұрын
I pulled mine out to get at a bolt for the EGR stand pipe thing and put it back in based on how the pigtail going to it was and live data says 14 14.5 15 degrees advance timing so is it good or no ? My 98 Ford e250 with the 4.2 l V6 Essex engine
@garyjenkins6629
2 жыл бұрын
I'm still confused. I'm starting with a used motor with no synchronizer. How does this tool help me?
@Lxmustang805
2 жыл бұрын
Thank you sir , we’ll explained .. a lot of these guys , can’t explain shit . This will help me a lot when installing this on a freshly rebuilt 3.8 ..
@lilchuy1485
2 жыл бұрын
Hi, what is the name of that tool, im about to replace my timing chain i i notice that censor so im a a stand still until i find that tool
@bgfixit
2 жыл бұрын
Ford Timing Synchronizer
@bgfixit
2 жыл бұрын
Or camshaft synchronizer alignment kit www.rockauto.com/en/catalog/ford,1997,f-150,4.2l+v6,1122455,ignition
i replaced it with the tool on but didnt put the timing in center dont know how to do that, its running fine but misfiring and turning off when im at stop and accelerate
@ufartface
3 жыл бұрын
there are 2 tdcs and what cylinder?
@bgfixit
3 жыл бұрын
If you have to ask, you probably shouldn't be attempting this procedure.
@jciabatoni
2 жыл бұрын
It's the 1st cylinder, front left. For future reference. Timing marks should be on damper/ counter balance wheel. And the block will also have a timing mark.
@davidturney2975
3 жыл бұрын
What year engine? I've got a 2007 throwing a code for that sensor
@bgfixit
3 жыл бұрын
This is a 2002 engine in a 1997 truck
@davidturney2975
3 жыл бұрын
So it should be similar to my engine then? Thank you
@matthewsempsrott6489
3 жыл бұрын
Can you replace the sensor without having to fool with the synchronizer?
@bgfixit
3 жыл бұрын
Yes.
@bgfixit
3 жыл бұрын
Yes, if just replacing the sensor. No problem, 2 screws, simple swap.
@ihulk1
3 жыл бұрын
@@bgfixit appreciate it my sensor just came in today so hopefully it does the trick.
@rubbermallet3873
3 жыл бұрын
do you have the link for the tool you used to set timing on the 4.2 L?
Пікірлер