Hi, I just tried changing my lift cylinder gaskets. Looks like they sent me parts for another Ford. The O-ring is way too big, cant get cylinder even close to putting it on. Then they sent me a split ring plastic thin ring for the inside. Where did you Order yours from? Thanks.
@tedpappas1559
3 ай бұрын
I'm not sure what tractor you have, but this is the link to the piston seal that fit my tractor www.messicks.com/parts/new-holland/sba050309017
@elitebowman5386
3 ай бұрын
C@@tedpappas1559thanks for the reply. I went back and found your messages about where you got them. I ended going thru a dealer in Rochester, NY. Thank you.
@tedpappas1559
3 ай бұрын
@@elitebowman5386 Sounds good, I hope it works out for you this time 😏
@elitebowman5386
2 ай бұрын
Hi, I got the right parts for my 2110 Ford Tractor now. I have them on the piston now. At 8:00 minutes on the video, your rod is centered so you could slide the cylinder in. How did you do that? Mine is down, and when I picked the 3 pt. Hitch up, it is way back and still can't center that Rod so I can slide it into the cylinder. @@tedpappas1559
@bcchristopher688
5 ай бұрын
Can you use in a shower drain? Obviously can't remove a trap, if there is one.
@tedpappas1559
5 ай бұрын
I have and it worked great
@giuzupp
7 ай бұрын
Is the Trigger Variable speed.?
@vicstevens2149
7 ай бұрын
Ted does that cylinder have any affect on the front loader. I have no hydraulics on my on my 1920 Ford tractor the loader and the three point went out at the same time?
@tedpappas1559
7 ай бұрын
Hi Vic, no I don't think it would effect the front loader at all. I would think you need to check the hydrualic pump or maybe a relief valve.
@leonsuggate3478
8 ай бұрын
Very helpfull - ive bought a 1920 with 800 genuine hours and its 3pl is bouncing with a load on it , so am just about to embalk on doung the same check now . 😊
@tedpappas1559
8 ай бұрын
Good luck 👍, my tractor is still working great and it's been 3 years since I posted this video. The hardest part is trying to get the seal over the piston, but once you get that, the job is pretty easy. I am glad the video helped out. Take care and God bless.
@billybarthol4768
9 ай бұрын
Where can I order these parts , 1710 I'm having problems finding this!!
@erichouwen3771
10 ай бұрын
Great video. I have a 1720. Is that the same seal. O rings were fine, but seal was disintegrated.
@tedpappas1559
10 ай бұрын
I am glad the video helped. I am not sure if the seal is the exact same for the 1720 as it is for the 1920. You can try calling www.messicks.com/ to see if they can help. That is where I bought mine.
@erichouwen3771
10 ай бұрын
I already got the rubber O rings from Messicks (buy from there all the time) but dont' know why they did not include the oil seal. My fault for not realizing your the 1920 not 1720, I got the seal locally, which you listed and apparently it is different because it is just a little too big. I'll call Messicks in the am. @@tedpappas1559 Again, thanks for the video- I am sure this is the fix. Was your hydro fluid milky. mine was- guess I now need to know the capacity for a full drain and fill.
@tedpappas1559
10 ай бұрын
Replacing the seal definitely worked for me. I have no trouble with my 3 point bouncing anymore, even with heavy implements. My hydro fluid was not milky, so most likely you got some water in there and should change out your fluid. Good luck 😀👍 @@erichouwen3771
@kevindufour2757
11 ай бұрын
1720 the same parts?
@tedpappas1559
11 ай бұрын
I'm sorry, but I wouldn't know if they are the same parts. You can go to www.messicks.com/nh/136474 and it should be able to tell you what parts your tractor will need.
@ederrodriguez9918
11 ай бұрын
For how long have you used this snake?
@craighatch3221
Жыл бұрын
Just wanted to say thank you for sharing. You did a great job.
@tedpappas1559
Жыл бұрын
Thank you sir 👍
@billybarthol4768
Жыл бұрын
Where can I order the parts?
@billybarthol4768
9 ай бұрын
Where can I order this for a 1710 ? 11:04 11:04
@snurb48
Жыл бұрын
This was a fantastic video, not one second of "oh for crying out loud.....do we have to watch this guy wash all the parts, etc.". YOu know what I mean. I know this is three years late but would a 'shuddering' as the three point is adjusted when box blading be of the same issue? This old 94 Honda 6522 I picked up runs and operates perfect with the exception of not being very smooth on 'creeping' the 3pt. stick on the fly. So the best I can do to explain the lack of response from stick to action of implement makes for a headache grading a road smooth! I'm not sure if I'm understanding the bounce or hunt is the same problem. I have heard others mention their problem was like the system was constantly reacting up and down without stick input? Mine holds, adjusts great for draft control, holds in position once set, it's just hell trying to make small adjustments to the 3pt. for hi-lo grade corrections and of course the shudder when dropping the hitch down. Thanks, I could have sworn you were a tractor mechanic for how you went about taking on your problem. Have a great Day!
@jamescc2010
Жыл бұрын
How much does a plumber charge to unclog kitchen sink our bathroom sink like this?
@tedpappas1559
Жыл бұрын
My experience has been anywhere from $50 to $100
@stanleykeith6969
Жыл бұрын
You better invest in a better Mic ! Can't hear YOU !
@TaitGuy
Жыл бұрын
Thanks, Ted! Good info! ~ D
@fullers1966
Жыл бұрын
When you replace that seal before taking it apart did you have to drain some oil
@tedpappas1559
Жыл бұрын
No, I didn't have to drain any oil on mine 👍
@rosemariemocan357
Жыл бұрын
He is not a pup and he is definitively a pro, but you dear Ted seam a very "slow student". Your part would have been to prep for the bird not to march around your GSP like a hippo in a china store. Your pointer is gorgeous and surely masters his job. Perhaps next time you detach the leach while letting him free on unknown terrain. I gave a thumb up for him.
@prostar505
Жыл бұрын
did you really fix it you didnt show it working
@clauderequier1925
Жыл бұрын
Trop tard pour la reproduction
@YeahImSaitama
Жыл бұрын
Yea I was tired of using the k45, just got this a few days ago….best machine I’ve ever used. So light and the cable does not even kink like that k45
@jacobnabors1268
2 жыл бұрын
do you know if the 1520 has the same size oil seal?
@heywoodjahblomie325
2 жыл бұрын
HEY Ted I have the same problem on my 1720 ford tractor. I see you used CNH brand piston seal. Would you let me have the name of the company you were able it through. The Ford tractor parts in town Says FORD sells an oring and back up Ring. TO replace the USeal Thanks for your help John Bigger 9/12/2022
@tedpappas1559
2 жыл бұрын
www.messicks.com/
@tedpappas1559
2 жыл бұрын
Hi Heywood, I got the seal from Messicks. They seemed to be the only one that had it. I left the link for you. 👍
@aux1z11
2 жыл бұрын
Did that rear piston seal also mess with your bucket loader ? I just got a problem yesterday with both front and back not wanting to lift or go down and making whining screetch noises, it might need a good bleed as I had all apart last fall to change the clutch but I don't see any where to bleed it or find any info on bleeding it.
@tedpappas1559
2 жыл бұрын
No, the bucket lifted fine, it was only the 3 point lift that was effected and seemed to bounce with a heavy implement on it. You might want to try draining the system and changing the filters to see if that might help.
@prostar505
Жыл бұрын
you have a hydrolic pump issue
@antikoerper256
2 жыл бұрын
Does anybody know if the applicance can work on 220 V elecrical current? I'm asking because I'm based in Europe and ordered one but it doesnt say if it could be used on more than 120 V electrical current
@danielwells4655
2 жыл бұрын
Great review, one question, can you use on toilets or just drains
@tedpappas1559
2 жыл бұрын
As far as I know, just drains. Thanks 👍
@aungmyint8534
2 жыл бұрын
looking for part no on piston seal; please let me know also where to buy it; thanks. also I need o ring to be replaced.
@tedpappas1559
2 жыл бұрын
I bought all my parts at Messicks www.messicks.com/part/sba050309017/seal-protection
@investorgeny
2 жыл бұрын
Thank you for sharing. 🤝
@ryanfairclough3394
2 жыл бұрын
Thank you! I have two 1320s and have been afraid to do anything hydraulic related until now. I will be subscribing and checking out the rest of your videos.👍🤝
@t2tarantula552
2 жыл бұрын
How old is this pup here
@tedpappas1559
2 жыл бұрын
He was almost 11 months old
@user-oh5vs7yz8b
2 жыл бұрын
體態優美的狗❤️
@rutgershouses
2 жыл бұрын
Pays for it self in one use
@freedoyopothman6491
2 жыл бұрын
Why you show the dog ..hahaha
@banjoeypicks
2 жыл бұрын
I just bought one myself. Pleased with it as well!!
@russbyrd4359
2 жыл бұрын
I've got a Ford 1720, you wouldn't happen to know if its the same parts as your 1920.
@equalls3
2 жыл бұрын
Did this help with the strength of the hydraulics? Mine is not hiccupping but seems to be getting weak.
@tedpappas1559
2 жыл бұрын
Hi Steve, yes, it fixed my 3 point lift from bouncing. If you have weak hydraulics, it could be a different issue.
@puppshades2554
2 жыл бұрын
beautiful dog , but my friend do not walk in front of the true hunter(dog) hi is the master here you only the shooter loll keep the very good job whit that outstanding animal excuse me hunter loll
@Corgis47
2 жыл бұрын
WOW!
@shug2795
2 жыл бұрын
Nice looking pup with tons of natural ability. Unfortunately, you train as the vast majority of trainers did many years ago AND, still do today. First off, your dog was ALREADY pointing when you said "whoa". So, regardless of what your intentions were, this dog will not reliably hold point unless you say "whoa" and as time goes on, you'll need to repeat it more often. Why did you whoa an already-pointing dog? Basically, you have taught him a "whoa" dependency. Instead, your dog needs to learn that if he breaks, the birds gets away, EVERY time, NO shots fired. You don't need to speak AT ALL while the dog is learning this. Subsequently, your dog learns to point out of volition and NOT from "whoa", corrections, check cords, e-collars, etc. Why? Because done properly, he soon learns that in order for you to shoot a bird which he subsequently gets right in his mouth, he cannot chase. He MUST hold point. Bird dogs trained this way find more birds, especially wild birds, handle better, etc. etc. ;) Depending on where you live, I can recommend a competent trainer.
@pedrothehunter3721
2 жыл бұрын
U right bud well said
@shawntatro8681
2 жыл бұрын
Lot’s of issues with this video, cringe worthy!! 1. Never use a metal pick on an o-ring, they make plastic ones for that. 2. Never put wheel bearing grease in your hydraulic system. Use hydro fluid. 3. Lift he arms to make it go in all the way before you crush something.
@tedpappas1559
2 жыл бұрын
Sorry I didn't meet your high standards Shawn. I am not a tractor mechanic nor claim to be. Just trying to help people who have the same issue but have no idea how to fix it. The 3 points you brought up are good ones, I wish I knew before making the video. Maybe you should make your own video to show how it's really done, instead of criticizing others.
@danlevesque589
2 жыл бұрын
Great info but just wandering if the bucket attachment also doing the same or was it only the 3 point hitch? Thanks in advance.
@tedpappas1559
2 жыл бұрын
No, it was only the 3 point hitch.
@danlevesque589
2 жыл бұрын
@@tedpappas1559 Thanks
@donnablackwood5909
2 жыл бұрын
I am totally in love with this breed. They are beautiful and amazing. Might have to get me one.
@uneasyrider6533
3 жыл бұрын
I have a 1320 with the same problem. I really appreciate this man!
@tedpappas1559
3 жыл бұрын
Thanks Greg, I am glad it helped you out. God bless.
@ryanfairclough3394
2 жыл бұрын
Do we know if it's the same part number for the 1320 and 1920?
@renatogomesdacosta1153
3 жыл бұрын
Melhor raça de cachorro pra caça de perdiz
@jasonbradley7973
3 жыл бұрын
I guess I am going to do this pretty quick. I have a 1920 purchased by my dad in 1990. The lift just started to hiccup. I will replace the hydraulic filter first to see if that is the issue. This is the only issue this tractor has ever had.
@tedpappas1559
3 жыл бұрын
Hi Jason, most likely it is the piston seal. The 3 point starts to hiccup because the seal is allowing hydraulic fluid to leak through which is causing the 3 point to intermittently fail as the pump is doing it's best keep it where it belongs. The job isn't too hard though. I hope this video helps you out. Take care and good luck.
@justinkaercher2677
3 жыл бұрын
Thanks for including the part numbers I just ordered my seal.
@tedpappas1559
3 жыл бұрын
Justin, I'm glad it helped
@jasonbradley7973
3 жыл бұрын
Ted. Sorry to bother you again. Would you happen to have the Part or Spec number for the Hydraulic Filter for the 1920? New Holland is telling me there is various types for this tractor. If you dont have it written down somewhere, dont worry about it. I am sure I can find out. I just figured I would ask someone who has dome it before . Seems like Ford new holland mechanics only know about new equipment. My email is [email protected].
@tedpappas1559
3 жыл бұрын
@@jasonbradley7973 - Looking at the parts manual, I am showing a Baldwin filter BBT8505. My tractor is at a friends house right now. I will call him today to see what filter is on my tractor and let you know.
@tedpappas1559
3 жыл бұрын
@@jasonbradley7973 - These are other filters that are also supposed to work: Fleetguard HF35359 Ford SBA340500410 NAPA 1208 Wix 51208
@jasonbradley7973
3 жыл бұрын
I really appreciate your help.
@troyadams3079
3 жыл бұрын
Thanks for the video. I have a 1720 with the same issue
@tedpappas1559
3 жыл бұрын
I hope the video helped you out. Thanks
@kingpin9733
3 жыл бұрын
I just brought one today $114. Seems like a solid tool. I hope it holds up.
@tedpappas1559
3 жыл бұрын
I hope it works as good for you as it did for me. I have used it several times at my house, and a couple times at friends houses. The tool has definitely paid for itself, and has save my friends money also as they were about to call a plumber. Good luck and God bless.
@wingerrrrrrrrr
3 жыл бұрын
I try to make sure to wipe the auger after use and drain the drum so it's not stored in a pool of dirty water for the extended periods between uses. Better still let it dry out before retracting. An oily cloth to wipe it down as you retract it will help it last forever. It's an excellent tool that deserves the bit of extra care on my part.
@timbarbee9421
3 жыл бұрын
Excellent video. Now I can fix my nh 1720. I call her bouncing Betty.
@tedpappas1559
3 жыл бұрын
I am glad you found the video helpful. Good luck with Bouncing Betty :)
@terrellscaife2411
3 жыл бұрын
Ha Ha that hand heal and snake could actually be attached to a drill i’ve use that same type of hand sneak attached to my drill and unclogged A 2 1/2 inch drained pipe
@darendth8594
3 жыл бұрын
Good boyee! Wow. This IS the benefit of a good “whoa” before getting on birds. Great and stylish. Pleasure to watch. Sharing with friend with a 10 month old. Thanks for share.
Пікірлер