Hi Mark just wanna find out how to set fuel priming and engine cool down time on the controller
@spiritualviking8094
3 ай бұрын
Trying to find out how to remove the low water level alarm but im failing. Any help? The water level is okay and everything runs as it should but the alarm wont go away
@abbasnaim-x3y
3 ай бұрын
My generator is not starting as i want
@AliAkbarEsmaeeili
3 ай бұрын
Hi good time How can lock and unlock screen or permition to parameters on dse7320 Thanks
@alamgeeransari5727
4 ай бұрын
how to set generator log out
@alamgeeransari5727
4 ай бұрын
how can set emergency alaram
@RayDe-n8h
4 ай бұрын
Is this compatible with a Smart Gen controller?
@philipaddae3628
5 ай бұрын
My generator is over frequency what should I do
@md.sahinmirdha234
5 ай бұрын
Thank you
@Tanha_8817
5 ай бұрын
How to reduce or increase the running meter of the generator
@dldchannel1316
6 ай бұрын
Already did but why the setting keeps coming back to its original after switching off the key switch. Thanks for your reply
@DorahQuaicoe
6 ай бұрын
Dg generator shutdown when I put new AVR on it what causes that
@AdnanJayyousi
9 ай бұрын
I have a case where there is a chiller connected using star-delta and the GenSet trips, do you think it will help ?
@ГригорГригор-у1й
10 ай бұрын
Hello. how to turn on the ignition without starting the engine ? DSE 7320
@ГригорГригор-у1й
10 ай бұрын
Hello. how to turn on the ignition without starting the engine ? DSE 7320
@ГригорГригор-у1й
10 ай бұрын
Hello. how to turn on the ignition without starting the engine ? DSE 7320
@alexgoverman634
11 ай бұрын
CAN I CHANGEA TIME OF RUNNING MOTOR
@atkingapu7040
11 ай бұрын
how to fix under and over voltages in cumins control DSE 8610 KII
@ilkhombakhtiyorov3043
11 ай бұрын
I need pin edit DSE 6120
@ahmedfarhan3497
Жыл бұрын
Memory corruption Refer to manual Please help
@Truthspeaker-c7u
Жыл бұрын
Can anyone tell me genrator is stoped after 9 secs saying generater at rest how to fix it it says saftey on delay
@iguanregodsglory3399
Жыл бұрын
Mine will show return delay and off after 30 seconds and won't start automatically What should I do?
@muhammadakram-nx7oh
Жыл бұрын
Good
@muhammadakram-nx7oh
Жыл бұрын
Good job
@AsimiTerupo-so2bb
Жыл бұрын
How to reset page please
@abdenourmerouane
Жыл бұрын
Dear sir , I have a 400 kva bertolis eco 40 generator and cursor13 engine when I charge it deep sea after a charge of more than 50% I receive a message displayed on the screen ECU AMBER Warning high or short voltage check engine SPN65619, IMF 3 OC 196 . what is mean. Best regards
@houssammansour9230
Жыл бұрын
DSE6110 i need change to bank 2
@josephotokunorsackey3895
Жыл бұрын
How do one trace earth fault on a generator set
@553castrojhay
Жыл бұрын
Hi sir my deepsea controller is DSE7310 volvo penta engine 500kva if I start up my generator 10 to 20 second monitor showing ecu amber .and generator under voltage.please give me advise
@chuckvenable4409
Жыл бұрын
I have the dse7310 I just purchased. I was having an issue with the controller module shutting off and rebooting during run and at stop rest mode . I rechecked all B+ 12 Volts at pin 2 and B- at pin 1 for poor connections. Everything is good. Some times the module would just go dead and not reboot until I removed the battery terminal and reinstall it. This issue was intermittent. It didn't always shut off . My question is, could a intermittent shorted coolant temperature sensor cause this condition? Does pin 16 that the coolant temperature sensor connects to put out 12 volts ? This is what I'm reading at pin 16. Any advice I greatly appreciate.
@khalidali9325
Жыл бұрын
Hi sir my jurnater is GCB TRIP plz solve the method
@mdrana-kp3kt
Жыл бұрын
Nice
@DieselGeneratortraining
Жыл бұрын
Thanks #powerlearningchannel
@aliahmedaltrhone2066
2 жыл бұрын
So what's the ECU warning ⚠️? please
@abdullahhamadeh
2 жыл бұрын
Hello, i have a problem with my kubota generator, when the generator shuts down ,it will not cut the power, it makes the electricity feather or turns on and off while shutting down, i need help on how to fix that
@mansooraziz1236
2 жыл бұрын
How increase display light
@fendibaene5398
2 жыл бұрын
Apa penyakit mensi controller tidak bisa hidup bisa di sentarte Tdk hidup tolong di jelaskan bahasa indonensia
@nishad9048
2 жыл бұрын
I connect 30kw 3 phase motor to 100kw generator but when it ON getting under voltage alarm let me know y
@ridamuftah2500
2 жыл бұрын
This video very useful for me, I used this function with heavy staring current load, thanks alot Engineer
@vinoth6747
2 жыл бұрын
Maintenance alarm 1 how to Reset with out laptop
@kaayosmomastersem8887
2 жыл бұрын
this module is the same model of my generator..may i ask u sir.how to reset this kind of module to going back the display on the screen showing again..because only blue screen can show .not just like before what happen.
@zelekeayalewbaychekn4260
2 жыл бұрын
hello hello my dear i have 100kva perkiness generator when i tray to start after starting the generator stops and on the display over frequency how can i adjest it
@kelebogilemeje4138
2 жыл бұрын
Why do you suggest max of 0.7 ,what if it is set at 2.2, what would happen to the generators?
@محمداسيل-ض5ت
2 жыл бұрын
At my DSE 6110 running time always 0 h 0 m please help
@muhmmadtariq
2 жыл бұрын
Sir Gen over votag gen shtdown
@sandeepshinde9230
2 жыл бұрын
KG745 please provide information... Deep sea kg745 controller..
Пікірлер