There is also 4 Allen screws in a x pattern behind the dial that can adjust where the big hand starts. Instead of moving the dial it will be at 12 o’clock and u can c alienate it that way. I like my hand at 12 o’clock
@TechTomTTSE
Ай бұрын
if it's not around 12 o'clock, your edge finder had some issue in the past
@ken7u7tube
3 ай бұрын
Thank you for your video, that was very helpful
@Mr.T-HUX
3 ай бұрын
Thank you Tom. Awesome guide.
@Verbickas
4 ай бұрын
At 3:30, you are wondering about the English name. it's a Dial Test indicator. Other than that, your English is lovely. Good video.
@TechTomTTSE
Ай бұрын
thank you ❤ you know "TTSE" stands for "Tries To Speak English" i planned this channel to also improve my technical english, but then life came inbetween.
@paulmorrey4298
4 ай бұрын
Thanks
@wiredodger60
5 ай бұрын
Nicely done Tom. You educated us well on how to calibrate a Haimer! Wish I had the German language as fluently as you have done it here in English. Well done! Looking forward to seeing you on your next video. Best.
@TechTomTTSE
5 ай бұрын
Thank you <3 I had the plan to make all my german videos in english again. But my time schedule is so tight right now. My plan was to force myself into learning technical english, because my english is pretty bad. "TTSE" stands for "Tries To Speak English" 😂😂😂
@alefs.5980
6 ай бұрын
Obrigado por compartilhar do seu conhecimento
@rx1laser
7 ай бұрын
Thanks! Tom This helped a Great! deal.
@JarppaGuru
Жыл бұрын
6:34 its mean your zero is there just 2 turn 2mm xD easy, but is fine you can rezero it looks better. and recalibrate again when use another machine with different cone or remove it from that holder you need calibrate again it wont go straight and centric
@TechTomTTSE
Жыл бұрын
Yes. Even when you change the tip, you have to check the concentricity
@hammerofluke2013
Жыл бұрын
Didnt know I could turn the face of my haimer until now. Perfectly calibrated 👍
@NicolasMartinianoGom
Жыл бұрын
More English videos, i am from Argentina and English is a good way to learn from you. You are very easy to understand. Simple and efective. Thanks, awasome vídeo
@TechTomTTSE
Жыл бұрын
I'll try ... i'm german and my time is rare these days :(
@krzysraf5798
Жыл бұрын
I bought very similar 3d Edge Finder from alliexpress and because this simple short video I have understand in a minute how it works and what is all about concentricity after changing the end of the tool Very useful movie Regards
@BogdanHurezeanu
11 ай бұрын
on aliexpress i find only versions for mach3 ? did you find one that is more rugged?
@jefn5530
Жыл бұрын
Nice video
@45calshooter
Жыл бұрын
Nice video.
@easonchen8257
2 жыл бұрын
Thanks for your sharing. For the 3D edge finder I have a question if you can help me. When I use 8mm tip on the probe, the indicator will show what number to tell me its the work edge? i know when the tip is 4mm the indicator shows 0 to identify work edge. Your help will be highly appreciated
@TechTomTTSE
2 жыл бұрын
Hi, the 8mm version works the same. it has double the length and therefore travels 4mm. the indicator must also show zero.
@easonchen8257
2 жыл бұрын
@@TechTomTTSE thank you !
@oyvindhaave
2 жыл бұрын
Nice presentation. Good setup for showing things. Sehr gut. Danke :-)
Пікірлер