I did keep the original manifold however I installed a new exhaust system. The original had rusted out.
@ANOTHERSAVEDSOUL
2 жыл бұрын
NICE!
@fletcherjohnston4491
2 жыл бұрын
Fix the filter please
@schuylerhuff
2 жыл бұрын
Will you sale me that carb.?
@robertlivingston4986
2 жыл бұрын
I’m sorry, I did sell it to a friend for parts. He used the top half of mine to rebuild his carb on his ‘70.
@wymple09
2 жыл бұрын
I did this to mine. The only thing better would be a smaller bodied distributor, which I think can be found in the after market. The remote coil electronic uses a separate coil, but may be smaller. Number one can be anywhere on the cap as long as you index the distributor accordingly & follow the firing order.
@robertlivingston4986
2 жыл бұрын
Thanks for the tip!
@thecynic807
2 жыл бұрын
15 is too young 36 is too old 24 is just right.
@johnsarab4500
2 жыл бұрын
Not having a velocity valve, a bigger carb might bog down with full throttle.
@robertlivingston4986
2 жыл бұрын
I did have a little bit of an issue at full throttle from time to time however I don’t generally hammer down. But as for cruising, I have no issues. I also don’t take it on freeways or highways at high speed. But valid point, thank you!
@doggosonline5413
2 жыл бұрын
Where can I buy the adapter kit that you used?
@robertlivingston4986
2 жыл бұрын
I purchased most parts from Hawaii Racing in Simi Valley, CA
@ricardodelagarza258
2 жыл бұрын
Hello, my name is Ricardo. I have a chevy from 1978. Motor 250. Could I ever ask you some questions?
@robertlivingston4986
2 жыл бұрын
Sure
@lopezart2853
2 жыл бұрын
Orrrrr u could line up all the plates first… then insert the bolt through all three at the same time 😂
@robertlivingston4986
2 жыл бұрын
I was trying to step by step one take, not the easiest thing. Just wanted everyone to see the whole process. You are correct though, thank you!
@thecynic807
2 жыл бұрын
Next time set the gasket on the plate then put the studs in
@lopezart2853
2 жыл бұрын
Haha same thing I thought
@petermartnez1204
2 жыл бұрын
Maybe the video was made 20 years ago they didn't have the stuff they do now
@robertlivingston4986
2 жыл бұрын
No, I made the video the day after all the parts came in. It was a make it work situation. Mods can be difficult, especially with availability of parts
@lacolello6644
3 жыл бұрын
You never replied mate was the Holley swap worth it or not
@robertlivingston4986
2 жыл бұрын
Sorry for the delay. Yes very much. Power increased, idle smoother, higher speed and honestly in popping the hood its lot more impressive lol
@74nova36
3 жыл бұрын
Informative video. Thanks bro!
@robertlivingston4986
2 жыл бұрын
Thank you buddy! That’s all I wanted, make a vid. with really info not fluff
@THEVROD64
3 жыл бұрын
As simple Install video there is. Thank you for posting. 1. Mark Rotor position, 2 . Line up oil pump spline ,3 Drop in and hook up positive lead.........nice. Best video on this install. Thank you from Texas.
@robertlivingston4986
2 жыл бұрын
Thank you! Basic info is what I look for too.
@Ajaxaxxess
3 жыл бұрын
Got a 64 C10 with a 230, doing the same thing. Thanks for the quick walk through
@robertlivingston4986
2 жыл бұрын
Glad to help! I had a ‘65 I still regret letting go of. I would love to see a pic of you have one!
@bossgoon115
3 жыл бұрын
Hey where’d you get your oil cap on your valve cover?
@robertlivingston4986
2 жыл бұрын
It was off an older engine I had, I can’t remember what it came out of.
@donaldp4028
3 жыл бұрын
Well this work on a 230 inline 6
@cliffbennett3372
3 жыл бұрын
same principal. I'm just about to change mine out today.
@maxcinta5760
3 жыл бұрын
I once heard the 250ci engine will automatically time itself if you loosen the distributor bolt, and run it that way. It is said that the distributor will twist back, and forth until it comes to a dead stop where it sets itself up in a perfect timing setting. Is that story true?
@robertlivingston4986
2 жыл бұрын
I’ve tried it, it worked kind of on my ‘70 but I couldn’t get that cheat to work on this one. Good call, I didn’t mention that but yes that can be true
@McC_62
3 жыл бұрын
where is the electronic fan vid sir
@robertlivingston4986
2 жыл бұрын
Actually I did the video but it got corrupted and I couldn’t load it however I did remove the electronic fan, it was pulling to much voltage from the battery. I put in a new fan clutch and fan instead and no longer have heating issues.
@Touchingrass1
3 жыл бұрын
Did adding a 4 barrel and intake make much of a difference.
@robertlivingston4986
2 жыл бұрын
Very much. Smoother and a much more rapid response in acceleration
@Chucktinez
3 жыл бұрын
Hi what size fuel inlet does this carb use? I just ordered this carb and found out it doesn’t come with one. I can’t find info online
@Chucktinez
3 жыл бұрын
Hey man do you you know what size the fuel inlet fitting is? I just ordered this exact same carb but I can’t find any info online for the size of inlet I need to screw in to the carb. Carb doesn’t come with one apparently I thought it did
@tipstolevelupinlife5837
3 жыл бұрын
any more horsepower
@tags61
3 жыл бұрын
can anyone let me know what part numbers carb and adapter are cant seem to find them also will i have to change stock intake manifold thanks
@keithleeuwen877
3 жыл бұрын
Cool !
@mauriciosanchez7590
3 жыл бұрын
Que espera lleva carburador rochester?
@gkhost7409
3 жыл бұрын
Estos weyes aki no responden el español suerte yo tengo el mismo problema
@Geoduck.
3 жыл бұрын
Thanks for the inline videos Rob very nicely done.
@danaragon7405
3 жыл бұрын
Do you have a break out of the parts you used to complete this project?
@carlosmontanez1173
3 жыл бұрын
Can you further explain what you spliced the coil wire into? I see green and black wires connected into the yellow coil wire. Thanks in advanced
@byronhewitt9559
3 жыл бұрын
What air filter base do I need?
@timadams1827
3 жыл бұрын
I agree with the aftermarket intake. Seems like a lot of trouble to adapt everything down to the same small hole as the original carburetor.
@lacolello6644
4 жыл бұрын
Hi was the holley 350 cfm worth the change from the 1 brl ...u never said if it was better or not .. tell us please
@VinnyMartello
4 жыл бұрын
Just wait till you modify the cylinder head and go with a lump port!!!
@ryancerezo2934
4 жыл бұрын
How did you install the breather?
@rubenfilippus2956
4 жыл бұрын
Will the Turbo increase the speed or only the power?
@marthaflemming844
4 жыл бұрын
Thank you for very good pics while removing the carb and putting things in laymens terms - keeping it simple for us novices.
@camodudemtbh7594
4 жыл бұрын
I have a 250 4.1 Ltr 6 cylinder vara jet 2 carb any suggestions on upgrading it?? Thanks
@benjaminvaldez209
4 жыл бұрын
Where did you get that adapter from and are you able too use that other adapter for it if you can’t find the double too single carb adapter
@kaos8081
4 жыл бұрын
Where did you get the adapter for a double carb to a single carb
@mikeneff832
3 жыл бұрын
Drilled holes homemade
@Lordskeep
4 жыл бұрын
Hi, I need to do this same job. Where did you order the linkage parts from, like the cable and brackets. Could you give me some part numbers? Please let me know. it would help me a great deal. Thanks for the video.
@MJ-de7rb
4 жыл бұрын
Super clean
@chrisdenisewood3384
4 жыл бұрын
If your going to make a video, learn the proper name of the different items 🙄
@Patoreynolds97
4 жыл бұрын
Does anyone knows how the calefaction of this engine works? I've got the same one, but it's broken. Or if anyone saw a video or a web page where I can find how to fix it, i would appreciate it so much.
@D.Edward
3 жыл бұрын
YOU CLIMB IN ON TOP OF IT AND SIT ON IT LIKE YER HATCHING AN EGG, IT'LL GET WARMER.....JUST MAKE SURE YER TESTICLES ARE HANGING IN THE COOLING FAN SO IT DOESN'T GET TOO WARM ,TOO FAST........................................"cheers!"
@adriantomlin2902
4 жыл бұрын
Yes really need an aluminum aftermarket intake manifold for a two Bbl. Carb?!
@VinnyMartello
4 жыл бұрын
Two words: LUMP PORT. Get it! Get it now!
@xaviervarnum2252
4 жыл бұрын
Wow I sold my 77 c10 stepside cause I thought it was the points n condenser when I could've just bought a new distributor be SMH
@lolaerika4671
5 жыл бұрын
can you give me the part list? im trying to do the same thing
@nebur90716
5 жыл бұрын
Following
@stefanmagnuson2718
4 жыл бұрын
lola Erika did you get the list? If so, can you send it to me? Thanks Stefan
@manuelwatkins9678
5 жыл бұрын
the electronic distributor he's out of a 1970 V6 Chevrolet
@JimBronson
5 жыл бұрын
350cfm carb but how many cfm through that 1 barrel hole into the intake manifold? Nevertheless, nice upgrade, Holleys are the only carbs anymore for which service parts are plentiful, and knowledge is pretty widely out there in the public realm.
Пікірлер