Licensed 310s automotive service technician turned high school shop teacher. Making videos of common procedures on household machines and whatever else comes into the shop.
Nice video! Only one suggestion, use a bearing puller instead of a grinder if you have one.
@MR.LARSON92
2 ай бұрын
Hey thanks! Ya I didn't have one and at the time and my acetylene tank for the torches was empty too! Figured this worked anyway because most average Joe's have a grinder.
@paulettek3682
4 ай бұрын
I can't hear at full volume. No captions either.
@MR.LARSON92
4 ай бұрын
Will keep this in mind for future videos, sorry Paul.
@haydenrichardp3712
5 ай бұрын
Why use a greaseable bearing on the jack shaft when there is no way to grease it ? Older sleds had a way to grease them. They need done every 500-1000 miles. That’s why people have failures with these bearings. I just pop out the seals and clean the old grease out and re pack the bearings. A lot less work ! I’ve done this for years
@MR.LARSON92
5 ай бұрын
I didn't realise it was a greaseable until I took it out of the pack, figured it's in a sealed mount so I just sent it in. If it were a customer's sled I would have gone OE but I wanted to ride.
@user-fr5xm3ro7u
6 ай бұрын
Hi great video Would you be willing to or available to to do this job on my sled. ? 2020 sks Thanks Eric
@jordanthomas2210
6 ай бұрын
Nice work! How often should you do a overhaul like this. How do you tell if they are bad before you start. Reason I ask is, I am looking at purchasing 2016 800 Pro S Switchback with 8k on it. Top end was done under warranty. I don't believe the rest of the sled has been touched.
@FunHaverJJBernau
7 ай бұрын
Using a grinder cutoff wheel is the best way to get the bearing off the one end of the jack shaft…??
@MR.LARSON92
6 ай бұрын
Depends on the tools at your disposal, you can use a puller and maybe some heat if needed. I didn't have a puller so this was the best way for me.
@kwmiked
6 ай бұрын
Puller that has the 3 pins u put into bearing, put plate on with forcing screw and pop off. Amazon has a few different brands
@ultramonte327
7 ай бұрын
Why not use a puller ?? No chance of damaging the shafts that way
@BC-Ben
8 ай бұрын
Nice video! Wish I had this a couple years ago. Had the jackshaft bearing go bad after 2,200 miles and just like you said at the 3:00 mark, it messed up the retainer plate too. That was a downer of a day. I'm glad to see a good video on how to do this inspection and work yourself rather than having to have a dealer do all the work.
@MR.LARSON92
7 ай бұрын
Glad you liked it, thanks!
@terrymunn1224
8 ай бұрын
Here is another tip and you can take it or leave it ....your call.pack the back side of your seals where the spring is (if they have springs)with grease so when you tap on them the springs stays in place .Simple and it works .
@terrymunn1224
8 ай бұрын
I want to find some spherical bearings like you use for jackshaft and use them for my jackshaft in my matryx chassis.Would you have a part number for your bearings and ill see if they are the size i need for my sled .The oem bearings have no grease hole in them and i want to mod my sled to grease the bearing through the flange
@kwmiked
6 ай бұрын
12-1001 with steel seal has the holes in outer race to grease
@terrymunn1224
9 ай бұрын
I hardly ever comment on these videos however this may help you ...get a cheap dremel or jobmate rotory tool and some dremel brand fiberglass reinforced cut of wheels.Not the cheapies that come in the kit .They are nice and small for cutting off the inner race where room is tight .They are probably good for say two inner races each but work nice, easier to control smaller and less heat.Take care.
@terrymunn1224
8 ай бұрын
Good idea@@MR.LARSON92
@jamieweckel5260
9 ай бұрын
Great video!! Thanks man. What kind of bearings or kit did you use? OEM or aftermarket?
@MR.LARSON92
8 ай бұрын
I use aftermarket, I worked in a dealer for years they're all the same, with the exception of wish.com kind of stuff! I used allballs kits from royal distributing for this job.
@sleepybrew
9 ай бұрын
throw the bearings in the freezer and they will go right in
@paulbischoff2291
10 ай бұрын
Hey thanks a lot great step by step
@user-jp8jt5yi9y
Жыл бұрын
Корявая работа, Съемники есть для таких целей.
@MR.LARSON92
Жыл бұрын
I'm assuming you're referring to a bearing puller, you are correct however this gets the job done just as well and the average home owner can do it this way.
@jimbacon1939
Жыл бұрын
Great video, thx
@MR.LARSON92
Жыл бұрын
Glad you liked it!
@stevemattioli
Жыл бұрын
Excellent video. Thank you!
@MR.LARSON92
Жыл бұрын
Glad it was helpful!
@ronknapp9556
Жыл бұрын
Very helpful I have a pro ride suspension how do you remove the track off of those
@MR.LARSON92
Жыл бұрын
Hi Ron, very similar to this video except you don't have to remove the jackshaft. Depending on the year there may be some slight variations but the general process is the same. Take lots of pictures of every step as you do it it may save you a big headache on re assembly!
Пікірлер