Hi Mark. Are any more of these kits likely to be made? In the process of doing the same conversion, so kit would be awesome.
@Ritualz999
Жыл бұрын
Where can I find the conversion bearing? That's the only thing I'm hung up on to finish my kit.
@mhernandz2011
Жыл бұрын
You don’t need to add the + just put in the number .0002 the control recognizes it
@jeredfowler7194
Жыл бұрын
What are the benefits to this vs a standard sx pump
@SimsonSupermoto
Жыл бұрын
thank you
@iDiveDOTtv
Жыл бұрын
Why would you use the sheet metal enclosure to square your fourth. Sheet metal is far from accurate to the 'tenths indicator' you're using. You should do it to the face of the fourth or the face of the vice adapter plate.
@markkonschak6288
Жыл бұрын
I’m not running it across the sheet metal. I’m running the indicator across the precision ground body. The face of the fixture isn’t a bad place to check but can induce error if you’re fixture isn’t perfectly parallel.
@iDiveDOTtv
Жыл бұрын
@@markkonschak6288 That's a big error in the middle for precision ground 😞 Defo use the face plate, that's the bit that matters so that's the bit to measure 🙂 As an aside you'll get better measurements with that indicator if you turn it so the needle drags behind it rather than it being perpendicular to what you're measuring too
@georgehunter4023
2 жыл бұрын
If this is an HRT230 then you should set Z zero on top of a set of 6" of jo blocks or 5" for an HRT160.
@ryanc6574
2 жыл бұрын
hi Mark - this is awesome. Any ETA on when the kit will be restocked?
@markkonschak6288
2 жыл бұрын
I will be making another batch next week
@ryanc6574
2 жыл бұрын
Awesome - I see they're in stock now. Does a 750SS couch pump fit this? What is the conversion bearing mentioned for JS hulls?
@markkonschak6288
2 жыл бұрын
@@ryanc6574 yes the 750ss pump will work and the conversion bearing is to update to the rubber isolated bearing vs the solid driveshaft mount. Because a X2 driveshaft must be used.
@jasonarnold7578
2 жыл бұрын
How are you centring the stock within the jaws of the vice?
@markkonschak6288
2 жыл бұрын
I used a 5th axis self centering vise.
@jasonarnold7578
2 жыл бұрын
@@markkonschak6288 yes, I have the same vice. I meant centring the stock in the Y axis. Perhaps just setting with a ruler is adequate?
@zeke2566
2 жыл бұрын
Do you still sell the 750 jet pump conversion kit ,if so where can I buy it,thanx
@JamesBrown-su1nb
2 жыл бұрын
Doing the 550 swap did you have to use the x2 drive shaft?
@split141x
3 жыл бұрын
Thanks for the video! Helped me out a ton:)
@frankg4765
3 жыл бұрын
Just purchased this kit. From what I see in the video the original rubber pump seal isn’t used just the sealer, am I correct?
@zeke2566
3 жыл бұрын
Dark,tragic music from theif,that steals another's designs....
@guillermoabelar37
3 жыл бұрын
Hola vi tu video es lo que estoy necesitando Donde puedo comprar ese kit de conversión ? Gracias muy bueno el Video
@doublem6027
3 жыл бұрын
Awesome video! Thank you!
@shaunbaker8235
3 жыл бұрын
This video was epic,any way i can get the kit to south africa?
@markkonschak6288
3 жыл бұрын
You should be able to order form the link in the video.
@Fire_Power414
3 жыл бұрын
great video anthing better about this kit than the rhaas version?
@markkonschak6288
3 жыл бұрын
Quality and fit of the product. Also usually ships within 2 days.
@stuarthatfield6266
3 жыл бұрын
What prop did you go for hooker 9/15 or standard sx 750 ?
@markkonschak6288
3 жыл бұрын
Really depends on the engine setup.
@reneejayhudder9713
4 жыл бұрын
Thanks for the video ! Can’t wait to go home tonight and install it ! Your product is amazing !
Пікірлер