this is very useful because you dont have to solder anything directly to the phone and still can use battery when needed
@zodiacfml
11 ай бұрын
thanks!!!
@expression3639
Жыл бұрын
lol it's not "without battery" if you solder battery cells to it.
@BaxtiyorShodiyev-ks9vd
Жыл бұрын
Yaxshirogʻi yoʻqmi😢
@seegobinpersaud3112
Жыл бұрын
Cook
@onoaquino2949
2 жыл бұрын
kzitem.info/news/bejne/2Xh9qauPqpmagaQ How did you come up with the correct conclusion about the correct polarity of the battery circuit protection? You just showed us that those were the negative terminal and the positive terminal without telling us how you found those out. I would like to use 18650 batteries too for my old phone, but without your explanation, I might get 50% incorrect in guessing the polarity of the terminals. Please enlighten me. Thank you!
@sunmugarasa1319
2 жыл бұрын
More smart mobile hacks
@mahbubalam6565
2 жыл бұрын
Very fine!!!
@prentisboy2019
2 жыл бұрын
I got some questions
@mathematicsclassesbyrkshar8993
3 жыл бұрын
Lumia 535 mere pas bhi hai purana
@gameonly9761
3 жыл бұрын
Dont try this
@Alhussainba
3 жыл бұрын
Well done, clean and elegant. Was surprised seeing a Lumia, I have my Lumia 950xl on my table bare back, the motherboard is probably dead as it sunk at some point, but I wanted to learn how the wiring works so that the phone requires the battery to work. Unfortunately, I couldn't replicate it with my Poco f1 as the battery doesn't have a + and - pins, it has an FPC connector and I don't know how to deal with it.
@abidurrahmanchowdhury4412
2 жыл бұрын
A bit late here. Have you tried detaching the BMS from your OEM battery so that you don't have to deal with the whole FPC connector mess? The battery pack along with it's protection board solders to OEM battery BMS which then connects to phone via FPC connectors.
@rimckd825
3 жыл бұрын
Prob ok for MS phones - that's about all... None of my LG SPs look anything like this. Thnx anyway.
@umargul5644
3 жыл бұрын
Well done sir, thanks a lot
@mkcaplayz6978
3 жыл бұрын
You: Infinity% Me: 100
@inamulhoque2627
3 жыл бұрын
Nice idea. Thanks.
@urbantamizh5363
3 жыл бұрын
When I tried directly with usb cable to phones input battery terminal it starts up phone and after 3 seconds screen goes off...why it happens
@tgmtf5963
3 жыл бұрын
Too much power
@SiddharthHaobijam
3 жыл бұрын
if it is samsung higher end phone it could be becos u have to take account the pin next to the phones input battery terminal . it seems to send signal to the phone that it is not connected. i tried directly connecting 3.something volt to the input battery terminal but it starts up n shuts down soon
@markjarvillemartin4228
Жыл бұрын
Take the BMS board. It probably has 3 to 5 wires connection to the main board of your phone. Use the original BMS board, and solder your external battery on it
@ajaynagar1326
3 жыл бұрын
on off ho raha h baar baar
@johnjacobs3673
3 жыл бұрын
I try this and it worked .i use a zte battery to power a samsung galaxy j3 and it turned on however when i try to chargwe it it saids the batery is not compatible how can i fix the charging problem. Do you think it has to do with the bsi and btem wires not connected??? Please help me
@marketersourav
2 жыл бұрын
u have to charge your battery externally
@claudiofiero8523
3 жыл бұрын
Can you give us some more explanations about where does this battery pack comes from/ how you did it
@danthegreat7590
3 жыл бұрын
Well i know that if you have a battery of the same voltage it can be any kind of rechargable battery what i think hes doing here is wiring it directly to the positive and negative pins of the phone as long as its the right voltage it should theoretically work
@sweetpotato7993
2 жыл бұрын
@@danthegreat7590 But how would you charge this battery? I think he did not show that bit.
Пікірлер