hey! loved your video.. I have a question tho, I saw many other tutorials on this topic and found that some of them are using D6, some D7 and now you on D3 on arduino... as of a beginner and not having much knowledge about arduino, can you please tell me what's the difference and which one's better to go with?
@harwindsingh
4 ай бұрын
That doesn't make any difference, you can use any digital pin.
@unseenninja130
4 ай бұрын
@@harwindsingh thanks for the knowledge, dear! <3
@unseenninja130
4 ай бұрын
and also, would it need me to change any code if I'm using either of them?
@harwindsingh
4 ай бұрын
@@unseenninja130 yes, you've to assign the same the digital pin in the code.
@harishkhollam
5 ай бұрын
I clicked, I saw, I Subscribed!
@steveememer
6 ай бұрын
am i just too dumb or just an idiot to understand that from which port is the Arduino nano getting data to glow to lights 💀
@zlj7622
7 ай бұрын
What is this tool you were using to melt and connect metal?
@harwindsingh
7 ай бұрын
It's a soldering iron
@zlj7622
7 ай бұрын
Thanks
@TeilorJoe
8 ай бұрын
sardar ji🎉 tussi great ho🙏
@preetsingh1467
8 ай бұрын
Bro eh setup led tv te v kr ke dikho
@harwindsingh
8 ай бұрын
Bai TV layi pre built kits aundiya, oh vdiya kam kardiya.
@ozersk69
8 ай бұрын
hello! thanks for the video! I want to make your project, but I didn't understand its power issue. could you explain? I will use WS2812B RGB. also, how much is better to take LEDs per meter? monitor 27 inches
@harwindsingh
8 ай бұрын
WS2812B works on 5V, you can supply it from computer's PSU. Strip with 60 LEDs per meter works great.
@ishantakki
10 ай бұрын
Thank u so much 10000% work
@kenanargyaahnaf2830
11 ай бұрын
can i use nodemcu instead of arduino? and does the first and the last led connect to 12v or just the first led?
@harwindsingh
11 ай бұрын
Yes, you can use Nodemcu. You can connect power from either side.
@kenanargyaahnaf2830
11 ай бұрын
@@harwindsingh okay, so I can connect them looping. 12v and gnd from PSU connect to anywhere 12v and gnd pin in led. and one gnd for the arduino. right?
@harwindsingh
11 ай бұрын
@@kenanargyaahnaf2830 Yes
@vinaysaini2917
11 ай бұрын
How to do it home TV
@harwindsingh
11 ай бұрын
For TV you can use pre built kits.
@Viralhub1618
11 ай бұрын
sir how to change the data flow in this code I already pasted led on tv but the led lights are reversed left to right
@harwindsingh
11 ай бұрын
You have to realign all the number blocks in correspondence to your LEDs, in the configuration screen.
@CMD_IT
Жыл бұрын
This software does not load the system?
@harwindsingh
Жыл бұрын
Can you elaborate?
@anshupuzzel
Жыл бұрын
Hello, I am trying to follow the steps. Connected DIN to D3, both GND's of strips together with Arduino's GND. I am stuck at 12V output. Connected one end of red wire to 12V(end of the strip) but where will the other end go? can you please share a circuit diagram?
@harwindsingh
Жыл бұрын
You only need to power the strip from one side, leave the other side as it is.
@anshupuzzel
Жыл бұрын
@@harwindsingh So 12v of the end of the strip will connect to 5v pin of Arduino? I am leaving 12v at the start of the strip.
@harwindsingh
Жыл бұрын
@@anshupuzzel Supply 12v only from one side. No need to use both sides of the strip.
@itsmeswagger9726
Жыл бұрын
Bro I have a question if I use this led on tv ( only led strip) and play a video in laptop which is connected to tv using hdmi cable can I get the same effect on the tv?
@harwindsingh
Жыл бұрын
Yes
@Caspian198205
Жыл бұрын
Does HDR work? I use boblight and kody and there HDR movies do not work properly. The colors are faded and it doesn't shine fully.
@harwindsingh
Жыл бұрын
I am unable to answer this as I haven't tried any hdr content.
@prasadpawar6166
Жыл бұрын
isnt it risky to solder it when its sticked on monitor why not solder it before and then stick
@harwindsingh
Жыл бұрын
That is one's own choice. It doesn't harm the monitor if you don't heat it for too long.
@prasadpawar6166
Жыл бұрын
@@harwindsingh true but this is a diy project and it should be mentioned in the video otherwise someone could kill his monitor without knowing.
@andreaalgeri3199
Жыл бұрын
Impressive project. If I use a 12V led strip, I connect the PSU +12 output to the power line of the strip and the GND to the GND of the strip and that's it without any mosfet? Doesn't it create problems If I connect arduino to the same GND?
@harwindsingh
Жыл бұрын
No issues at all, it works great.
@Gustav.J
Жыл бұрын
What part do you use to deliver power?
@harwindsingh
Жыл бұрын
I attached the LED strip to the 12 volt line of the desktop PSU. You can use any power source like an adapter or any external PSU.
@buraknursen7002
Жыл бұрын
what are your psu values?
@harwindsingh
Жыл бұрын
I supplied 12 volts to the LED strip from the desktop PSU's 12 volt line.
@buraknursen7002
Жыл бұрын
@@harwindsingh What are the pros and cons of using ws2812B? and also what changes if I use uno instead of arduino nano
@harwindsingh
Жыл бұрын
@@buraknursen7002 WS2812B is a great LED strip. It doesn't matter which Arduino board you use, just make sure the output pin is correctly configured.
@spacebluemchen
Жыл бұрын
Is it possible to connect an LED strip with 30 LEDs per meter in parallel to get a 60 LED per meter strip?
@harwindsingh
Жыл бұрын
I don't think it's possible with the setup I used. According to me a strip with 30 LEDs per meter is enough for this project.
@JSlaig
Жыл бұрын
I'm curious if you can make it work with multiple monitors
@harwindsingh
Жыл бұрын
It'll work
@OldCarsAreFun
Жыл бұрын
Does this work with movies which have an other ratio than your screen. Giving black edge above and under the movie?
@harwindsingh
Жыл бұрын
Yes, you just need to adjust the height of the number blocks in the configuration.
@OldCarsAreFun
Жыл бұрын
@@harwindsingh thank you sir. it works great. Netflix doesnt allow screengrabbing. KZitem fullscreen works does work very well
@dekahobby
Жыл бұрын
Can i use atmega168p instead of using 328p?
@harwindsingh
Жыл бұрын
Yes, you can use any Arduino.
@shubhampatel8193
Жыл бұрын
Can you give me video links you used for testing the leds
@harwindsingh
Жыл бұрын
I just searched and was unable to find the exact videos. You can try searching "ambilight test videos", there are plenty of them.
@simonguillemain3807
Жыл бұрын
compatible with 2 screen? 2 arduino?
@harwindsingh
Жыл бұрын
Yes, you just need to modify the led layout accordingly.
@Relrion
Жыл бұрын
Is this able to work with games in Exclusive Fullscreen?
@harwindsingh
Жыл бұрын
Yes
@MMZ_Thumper
Жыл бұрын
Nice video. Could have used a closet shot of your computer screen to see what you were doing but it's manageable. I'm looking for a DIY for my TV so this won't work for me but I watched it anyway!
@ChrisBeard
Жыл бұрын
Pretty sweet!
@daveys
2 жыл бұрын
Nice!
@harasisgill
2 жыл бұрын
Awesome 👏🏽
@harsimransingh7480
2 жыл бұрын
💥 mesmerising
@TonesDroneVisuals
2 жыл бұрын
Wow. The reveal of the sunset was awesome.
@leeshiv5233
2 жыл бұрын
Marvelous 🔥
@junifferjardinez4851
2 жыл бұрын
sir need help my f450 fly stable but when i use yaw it drifts ang crash
@harwindsingh
2 жыл бұрын
Check your flight controller stick values. Make sure transmitter sticks output are bound to correct inputs of flight controller. This could also be due to overload of vehicle as thrust from 2 motors decreases while using yaw.
@junifferjardinez4851
2 жыл бұрын
@@harwindsingh thanks
@junifferjardinez4851
2 жыл бұрын
can u share your gain settings sir thanks
@harwindsingh
2 жыл бұрын
@@junifferjardinez4851 sorry, I don’t have access to that right now. But I used default values.
@junifferjardinez4851
2 жыл бұрын
@@harwindsingh ok thanks
@krishandhun9411
2 жыл бұрын
ECS Apne 40 A use Kiya hai iski jgh 30A use le sakthe hai
@harwindsingh
2 жыл бұрын
Yes
@krishandhun9411
2 жыл бұрын
Sir ye total kit apka Kitna price lga
@krishandhun9411
2 жыл бұрын
Sir Apne GPS dusra use liya hai to ye workkrta hai
@harwindsingh
2 жыл бұрын
Yes, it works great.
@krishandhun9411
2 жыл бұрын
@@harwindsingh sir muje ek help chaiye please sir contact no mil skthe hai
Hey this is amazing!!! 👍👍👍 but the LINKS are DOWN !
@harwindsingh
2 жыл бұрын
Thanks friend, let me check
@TusharGogna
2 жыл бұрын
Can this work for 55 inch tv too?
@harwindsingh
2 жыл бұрын
Only if you have an android tv. Otherwise you have to find some other kits
@WeRKnowledge
2 жыл бұрын
Great innovation
@WeRKnowledge
2 жыл бұрын
I want to make this, could you do this for me?
@harwindsingh
2 жыл бұрын
Sure
@skydroneindiahobby3239
2 жыл бұрын
Bro Fly drone please
@crucfx.
2 жыл бұрын
ok this is pretty fucking impressive. im wondering though, how well does this work with fast paced fps games?
@harwindsingh
2 жыл бұрын
I am not into games but it works great with games like gta 5.
@crucfx.
2 жыл бұрын
@@harwindsingh thanks for the quick reply. ill be following your tutorial it looks awesome and hopefully it would look good with fps. all these other brands just dont give the same outcome as this!
@shauryar6969
2 жыл бұрын
Hey! Please tell the color format for ws2812b leds.
@harwindsingh
2 жыл бұрын
It's RBG
@shauryar6969
2 жыл бұрын
@@harwindsingh thanks for such a speedy reply
@shauryar6969
3 жыл бұрын
Hi! Was making this project. How did you connect the strip to the desktops psu. Pls explain in detail. Sorry for asking too many questions.
@harwindsingh
3 жыл бұрын
Use the 4 pin connector of PSU. If your strip supports 5 volts use 5 volts line of PSU, otherwise use 12 volts line.
@shauryar6969
3 жыл бұрын
Can we use one power supply for different projects including this?
Пікірлер