If I wanted to make this stereo, would it just be 2 exact circuits in the same box? Nothing else required?
@slamcrank
9 күн бұрын
I must have missed how you made the impedance adjustable? Any thoughts? (Thanks for the video btw - it's great!)
@Naor-Hazan
2 ай бұрын
Just follow the old video and build my own REAMP Box! I did change the xlr input to a unbalanced TS Jack. And instead of a ground lift ive made it a mute switch thank you! awesome video
@georgeb7072
3 ай бұрын
what if the connector is not plastic?
@loganhall-tr5vk
4 ай бұрын
Badass, well done playa
@Twinhit
4 ай бұрын
Replying May 2024 I listened to the graphic starting about @2:38 and I could not hear any difference between the blue and red sound samples.
@togspots
5 ай бұрын
Parts list a 100k ohm pot, but schmatic shows a 10k pot. witch is it?
@jamesjack3992
5 ай бұрын
great video! I was wondering if it's possible to build a dual re-amping box in the same inclosure or if that could create any grounding issues? I'm keen to send signal through some stereo pedals.
@NewHopeAudio
5 ай бұрын
Would love to see some new content ❤
@StuffBudDuz
6 ай бұрын
The music is uncomfortably loud compared to your voice. Had to stop watching. Looks like a good idea, tho.
@santiagomoreno696
7 ай бұрын
Thanks, I just built one
@poindextertunes
8 ай бұрын
Have you ever used this to run vocals through a guitar effects signal chain? Like using a $120 guitar pedal compressor instead of a $2000 rack hardware compressor?
@-______-______-
8 ай бұрын
Lovely neat job into a very sleek little sized enclosure. Kudos!
@gigafuq8751
8 ай бұрын
hey Life Harmonic. I just built this pedal and I'm having some issues where the Impedance makes no difference in the sound when turned, and my reamped guitar sounds weak compared to plugging straight into the amp with my physical guitar. I'm running a TRS > XLR from an Audient ID14 output. Does the pedal need to be wires differently to accommodate for this? I can send through a photo if it helps thanks!
@bardicdad
10 ай бұрын
We've been rickrolled.
@eliatasti06yt
10 ай бұрын
would it be the same-ish schematic and components for a DI Box?
@ToneCraftFX
11 ай бұрын
🔥 🔥 🔥
@RicoRokkaRolla
Жыл бұрын
I did everything as you showed on the video and schematic and it doesn’t work. Really noisy. Pot doesnt work too. What is the problem?
@zygomar74
Жыл бұрын
@LifeHarmonic thank you for sharing this and answering questions. I have a buffered splitter and need to connect a germanium based pedal (Animato), which does not like low impedance. So my situation would be unbalanced jack input to reamped, higher impedance jack out. I went through your replies, but not sure if 1. your reamp box would fit this particular job and how wiring and maybe components would be impacted. Can you help ? Thanks a lot !
@driveblind6094
Жыл бұрын
The link to the schematics is not working it seems. Do you have a fresh link for it?
@coldworldmelancholy
Жыл бұрын
Thanks you so much for this video. I was able to make one using Tamura MET31 as the transformer and removed the ground lift switch (always set as lifted). The output volume is very close to the actual electric guitar and it is sounding great so far.
@dustinbeasley
Жыл бұрын
Great Video! I'm curious if there is a way to implement some sort of volume attenuator as well? Or does the impedance knob do this? I'm curious how you're sending line level signals into instrument level effects without severely clipping or distorting the input to them. Thanks!
@trevorus
10 ай бұрын
Volume controls are generally set up as a volume divider, this impedance adjuster is just adding series resistance.
@johnnyphoney5669
Жыл бұрын
Does this one pad the signal like -12dB? I assume that 10k resistor does it? I’ve seen some videos people are using diboxes in reverse but lowering the output from the DAW for around 12dB in order to not overload the transformer into saturation. But this resistor after the signal hits the transformer, right? I opened my Radial PRO-RMP and I see some resistors in between the transformer and the XLR pins. So in signal path those are before the transformer, not after it.
@tiagooliveira82
Жыл бұрын
Hello, starting from the principle of keeping the output impedance 10 times greater than the input. So wouldn't it be good to connect the output of the audio interface that is 100 Ohms directly to a guitar amplifier that is 1 M Ohm? Grateful.
@tiagooliveira82
Жыл бұрын
Hello. A doubt. I want to use the output of this Reamp Box in a real amplifier. What should the resistance setting of this variable resistor be? Thank you very much.
@vminator
Жыл бұрын
Doesn't NEED to be plastic just isolated from the chassis.
@blueswede74
Жыл бұрын
Thanks for sharing! Is the pot and the resistor necessary?
@fernaodmc
Жыл бұрын
Hi! Great job. In my case, the XLR conector has a dedicated fourth pin for groundind (pin 01 has no ground). So, what should be the best way to wire the gnd.lift switch? Between pin 01 and XLR ground pin, or between pin 01 and output sleeve, leaving pin 01 always wired to ground pin?
@amaurythewarrior
Жыл бұрын
ok i tried doing that with a stereo balanced jack connector (my fireface has jack line outs) but using a unbalanced jack cable for the line out. and nothing is working like it should. my understanding is to connect unbalanced to balanced, ring and sleeve should be connected, so with a unbalanced cable i shouldn't have to do anything since the sleeve will touch both the ring AND sleeve on the connector, right? my pot is doing nothing, i get audio on the ground... i'm sure i'm missing something obvious, anyone can help please?
@amaurythewarrior
Жыл бұрын
Well i ordered everything from farnell, so hopefully everything will go smoothly. i've been considering building a reamp box for a while. the L2A seemed a bit expensive for DIY, but who knows, maybe I'll realize I need more later
@MiniRacersRC
Жыл бұрын
Hey , my transformer is a yellow one and doesn't look quite the same the downside, is it going to effect the sound if I put it the other way? It also has 4 feet and a square ring around it...
@mchamerhead
2 жыл бұрын
would this work with all same for Transformer TM022? 1.5k primary, 600 Ohm secondary
@ShredEngineerPhD
2 жыл бұрын
GREAT Job man! :)
@mchamerhead
2 жыл бұрын
super videos ye have
@GraffHabit
2 жыл бұрын
Hey hey. I just wanted to say that you can add a step where you spray a protective clear coat over the paint so that finger grease and friction/use don’t tarnish the paint. I would even do two layers/coats of clear protection paint (not sure the actual name) if u really want it to last
@-______-______-
8 ай бұрын
Acrylic lacquer?
@GraffHabit
8 ай бұрын
@@-______-______- yes
@hkollner
2 жыл бұрын
Nice video. I am definitely going to try this build. I just have a question surrounding transformers. Commercial reamp boxes uses a range of different transformers for example Radial X-Amp uses a 10k/10k, L2A uses a 10k/600 and yours a 600/600. How does these affect the sound? As far as I read and understand it can affect the output volume? Can I use any of these transformers for this build and which will give me the highest output volume?
@tiagooliveira82
Жыл бұрын
This is my question too. Did you come to any conclusions?
@onurBrunonurBruno
2 жыл бұрын
Is it ok if I connect the remaining lug of the potentiometer to ground? That's the only way I get volume control
@50licks
2 жыл бұрын
Is there an alternate transformer instead of the one you've used? What should i be looking for. This transformer does not handle bass frequencies very well. Makes the sound too thin.
@LiveAnotherDay24
2 жыл бұрын
Can I skip the ground lift switch and just leave the third pin floating? or is there any situation that we need to connect to that ground
@cfiore88
2 жыл бұрын
Can I skip the XLR and just use a TRS stereo jack?
@dlvnmedia
2 жыл бұрын
Silly question but if I took out the XLR jack and added a 3.5mm jack could I use this to convert my modular synth signal to go into guitar pedals? I am trying to figure out so that I can try to avoid paying too much for a guitar pedal adapter for it since I am low on funds at this time but have all the parts for this in my parts bin if it would work
@ElChrissos
2 жыл бұрын
Thanks for the nice video. Very good and easy to follow instructions! I have the problem that whenever I turn the pot, it adds a lot of noise to signal, but only when the switch is set to 'Lift'. Do you have any idea what I may have done wrong? I'm pretty sure it's wired exactly according to your instructions.
@Jediroller
8 ай бұрын
Im just using my knowledge from reading amp forums, its probably working like it does in a presense knob for an amp, when you move the switch you can hear a crackling like noise because its biasing the circuit and thats actually DC voltage you hearing on the pot. Its probably normal operation but yeah mabye someone else can chime in. Hope this helps.
@crimsonrecording2820
2 жыл бұрын
Do you think it matters what king of wire you use?
@LifeHarmonic
2 жыл бұрын
No, you can use any wire you want. :)
@crimsonrecording2820
2 жыл бұрын
Cool thanks man
@ohmuseek4290
2 жыл бұрын
Can i use a 1M potentiometer instead? or can i not use a potentiometer?
@LifeHarmonic
2 жыл бұрын
You can use a 1M pot, but if it's a linear pot, the only really usable range will be less then a quarter turn. You can also go without if you don't use fuzz or similar pedals for reamping.
@uptownphotography
2 жыл бұрын
Well done and great info. I have seen some people use a DI box in reverse and also other people using a buffered guitar FX pedal (bypassing the effect) and get what seems like great results. Without actually trying those methods yet, time will tell. Your method is awesome, and I will build one if all else fails.. Thanks. Philip NYC Area
@onurBrunonurBruno
2 жыл бұрын
Great video!! My interface has 4 unbalanced outputs. Do I still need a reamp box?
@LifeHarmonic
2 жыл бұрын
Thanks! It's not absolutely necessary, but as you can see at the end of the video, a directly connected signal (ground) may result in a lot of noise.
@WillieFourMilli
2 жыл бұрын
I got some great ideas here, thanks for sharing this! ☮️☮️☮️
@TheSimonarne
2 жыл бұрын
would be nice to mix in with a regular amp or maybe use with a reamp box
Пікірлер