I've been thinking about trying to get a nitro, this one is actually kinda fast, I think this will be my first nitro model. great video and great location, I'm subbing!
@TheNitroAddiction
22 күн бұрын
Hell yeah brother nice rip
@narongrachmareongsit1978
28 күн бұрын
❤❤😂🎉😢😮😅😊. ไฟแอดพ์. ?
@Cafu1887
Ай бұрын
Hello - Nice video, i have The same. Which kind of glow plug do you use ?
@NitroRC96
Ай бұрын
@@Cafu1887 Thank you! I use a HPI B5, medium glow plug.
@Nitro_rc_life
Ай бұрын
I wish I had a track near by
@NitroRC96
Ай бұрын
@@Nitro_rc_life not many around nowadays! Shame really
@allaspectsrc4178
Ай бұрын
Love the all my savages nice rip appreciate the sub my friend..
@Nitro_rc_life
Ай бұрын
Subbed
@DarkMagician225
Ай бұрын
Any problems with your transmission and drive line?
@Nitro_rc_life
Ай бұрын
@MikePatt023 nope I did take it all apart and reassemble but still on factory everything
@Nitro_rc_life
Ай бұрын
Nice rip i absolutly love my gt6 xl your 5.9 is running mint. Mine loves to be lean and mean
@NitroRC96
Ай бұрын
Thanks for the sub! Love mine too, it’s a riot to drive! Runs very well, still running it rich! Will lean it out next time I take it out
@Nitro_rc_life
Ай бұрын
@NitroRC96 they are like that for the 1st Gallon or so at about 1 1/4 gallon mine just wanted to be rich then it changed and wanted to be lean as a rail and now it's a beast I have a video releasing today at 330 pm that's all my xl and it's lean and mean
@Nitro_rc_life
Ай бұрын
Also running torco 30/10 with a lrp r6 plug it's amazing
@hellraiser7935
2 ай бұрын
What are your carb settings? I don't think factory are even close to right. I took mine apart when I bought it and did the diffs, transmission, and servos. Having a hard time keeping it running!
@NitroRC96
2 ай бұрын
@@hellraiser7935 For me out of the box the low speed needle was set too lean, had to richen it during break-in. What issues are you having? I have mine set slightly rich, if I remember rightly the low speed needle is flush with the carb and the high speed is about 3/4 of a full turn from the stock settings. Factory basic settings always need adjustment in my opinion, they’re just a safe, rich setting to get it run in and started then adjust to your liking. Check your clutch, do your wheels spin a lot at idle if you lift the truck off the ground? One of my clutch springs snapped literally 6 tanks in, during break in. I never thought it would be that at the time and thought it was a tune issue. It always kept cutting out when I let go of the throttle, braked or came to a stop as the clutch dragged due to a snapped spring putting load on the engine at idle or braking. You did good taking it apart, I didn’t. Should have done it myself. Had quite a few screws come loose during my time driving it!
@electricnitrorc
2 ай бұрын
Nice run with the 5.9 👍
@NitroRC96
2 ай бұрын
@@electricnitrorc Thank you! Runs great, had a few issues with the truck previously but all sorted now.
@electricnitrorc
2 ай бұрын
@MrBrumbrine good that it's fixed 👍 What issues did you have?
@NitroRC96
2 ай бұрын
@@electricnitrorc A few, haha get ready! Clutch spring snapped, clutch bell bolt loosened out and worn the bearings out, no loctite in the 3 speed gearbox grub screws and they loosened, had to adjust the shift points,engine came loose, bolt had no loctite, front differential stripped, on and off switch kept switching off after landing a jump. Hope yours has been good! Any issues?
@electricnitrorc
2 ай бұрын
@MrBrumbrine That's a lot of issues 😲 only issue with my 4.6 so far is that a wheel came off, so I'm nowhere near yet 😅
@NitroRC96
2 ай бұрын
@@electricnitrorc Wheel fell off!?Wow, definitely wasn’t tight enough from the factory. Hopefully it stays good for you! I do like the 4.6, will probably buy one hahah
Пікірлер