The front grill and side marker combo, did you have to modify it? I’m doing the same swap but my grill seems to be long and the markers don’t fit. Suggestions? Truck is looking clean!
@mypoleinurhole
2 ай бұрын
Need the Pathfinder corner lights to match the grille. They're basically built upside-down compared to the truck style. Other than that, it pops right in
@562CaliPyro
3 ай бұрын
What tire size you running on the 4Runner wheels?
@mypoleinurhole
3 ай бұрын
225/45/17s
@ExplainwithShaun
3 ай бұрын
Are you running pathfinder fenders or the original 2wd ones?
@mypoleinurhole
3 ай бұрын
They're from a pathfinder. 4x4 trucks use the same fenders. I've ran this setup with 2wd fenders, too, with no issues
@uncleiroh6127
Жыл бұрын
Just ordered this can’t wait to get these guys on, did you run 14” wheels or bigger?
@mypoleinurhole
Жыл бұрын
Website says you can't run 14s. But anything above that works. I have 17s on mine. Fills out the wheel wells nicely
@littrollin
Жыл бұрын
are you running just the belltech leafsprings in the rear for the drop?
@mypoleinurhole
Жыл бұрын
Yea. I tried adding 3inch blocks but the transmission started making noise from too much pressure on the bearings. Even with the carrier bearing raised as high as it can go.
@williama76
Жыл бұрын
Does the back have a rollpan or you took out the rear bumper?
@mypoleinurhole
Жыл бұрын
Both. It's an oem panel/ roll pan. It had some weird looking bumper that I took off. The brackets wrapped around it
@joshuathompson2131
Жыл бұрын
Did you have an issue with your drive shaft angle and 3 inch springs?
@mypoleinurhole
Жыл бұрын
No. But after 4inch of drop on these trucks, you'll need to atleast space the carrier bearing up
@squidinkRC
Жыл бұрын
Those 4runner wheels go hard
@juniorb5417
Жыл бұрын
Did you have to make any modifications to the valance?
@mypoleinurhole
Жыл бұрын
Just trim the ends off cause it runs into the wheel well area. But that's it. And I just zip tie mine on so its easy to take off
@juniorb5417
Жыл бұрын
Awesome thanks for the info! Any good resources for that pathfinder headlight conversion? I got everything I need just trying to find something out there that shows step by step. Thanks again!!
@mypoleinurhole
Жыл бұрын
@@juniorb5417 everything swaps over. Just need the grill, headlights, and corner lights, then spice in the different headlight plugs. Straight forward really. Just have to pull the bumpers off. Do that by taking off the turn signal pieces and you can reach your hand in there. Take the horn off to make it easier on the driver side
@juniorb5417
Жыл бұрын
Thanks man!! 👍🏼
@modelx89
2 жыл бұрын
What muffler u running?
@mypoleinurhole
2 жыл бұрын
12inch glass pack, 2& 1/2 dia. Knocked the cat out since this video and it's deeper tone
@andrewzamora7245
2 жыл бұрын
I'd like to get in contact via Instagram to talk more about the truck
@mypoleinurhole
2 жыл бұрын
@mypoleinurhole
@andrewzamora7245
2 жыл бұрын
Where'd you find the flaps and windows "cover" thing
@mypoleinurhole
2 жыл бұрын
Got the flaps from a pathfinder I bought awhile back. Window covers you can get off rockauto. Mine are wades
@Pop__kuz
2 жыл бұрын
Do you know if the lowering leaf springs will fit a 2000 frontier regular cab? Thank you in advance
@mypoleinurhole
Жыл бұрын
Just seen your comment. Sorry. And I'm not sure about that one. Some on the fb pages might know
@imrichierichb7622
2 жыл бұрын
What size tires 🛞 are you running on those wheels?
@mypoleinurhole
2 жыл бұрын
225/45/17
@warrensantiago4961
2 жыл бұрын
what does re drilling do?
@mypoleinurhole
2 жыл бұрын
Lowers the rear an inch
@cre8iveone699
2 жыл бұрын
Nice glow 👍
@jretkl7959
2 жыл бұрын
What leds you have on the turn signals ? Is it from the pathfinder?
@mypoleinurhole
2 жыл бұрын
If you're talking about the corner lights, yes they're pathfinder clear lens. The one in the bumper are fcklightbar fog lights. Ran the turn signal harness to the corner lights
@jretkl7959
2 жыл бұрын
@@mypoleinurhole do you have the link for those fog lights ?
@mypoleinurhole
2 жыл бұрын
@@jretkl7959 fcklightbars.com/collections/fck-pods/products/lp-4-flushmount-pods They don't fit perfect. I made brackets with abs plastic to fill in the gaps
@jretkl7959
2 жыл бұрын
@@mypoleinurhole oh okay so the only thing you did is connect the turn signal connector to the corner lights ?
@mypoleinurhole
2 жыл бұрын
@@jretkl7959 yeah. On my 93 it was the same plug connector. Not sure on other years
@jretkl7959
2 жыл бұрын
Are the struts for rear wheel drive or 4WD?
@mypoleinurhole
2 жыл бұрын
Believe 2wd only
@kash4550
2 жыл бұрын
Will those rear shocks fit on with a 4 inch drop block ?
@mypoleinurhole
2 жыл бұрын
I believe so. But you don't have to change shocks while using blocks as the location of the shock doesn't move up or down. Just moving the axle up
@kash4550
2 жыл бұрын
It’s been real bumpy after I installed
@mypoleinurhole
2 жыл бұрын
@@kash4550 do you still have the stock shocks or have you changed them out?
@kash4550
2 жыл бұрын
Blue stocks
@kash4550
2 жыл бұрын
I don’t think it’s ever been changed
@victornaja7927
2 жыл бұрын
Off topic if you had to check timing on your truck what scanner would you use. Sweet truck I have a 95 d21 my self. Thank you
@mypoleinurhole
2 жыл бұрын
Mines obd1 so I had to use a timing light. Not sure on the obd2 trucks. Sure you could also use a timing light if it has the gauge by the crack pully. I went with +10 on mine. And thank you
@jamesvickery2486
2 жыл бұрын
Is the the front plastic scoop under the bumper a nissan scoop or ... ???
@mypoleinurhole
2 жыл бұрын
1st generation s10 lower valance
@jackscottjr8132
2 жыл бұрын
What kind of rims are those your running
@jretkl7959
2 жыл бұрын
What size tires do you have ?
@mypoleinurhole
2 жыл бұрын
225/45
@ItsStuder
2 жыл бұрын
Any real difference between using 3" drop blocks in the rear (belltech 6200 or 6202) vs using the 3" drop leaf springs?
@mypoleinurhole
2 жыл бұрын
The leaf springs are stiffer than stock. Would probably ride better with blocks if you're using it as a daily. And using stock leafs you don't have to change out the shocks
@ItsStuder
2 жыл бұрын
@@mypoleinurhole Appreciate the info. Will probably choose blocks for the softer ride
@itzamedave6242
2 жыл бұрын
Redrill and sliders you won't need sway bar looking good through
@mypoleinurhole
2 жыл бұрын
Been planning on it. Just haven't got around to it
@jretkl7959
2 жыл бұрын
Hey bro , those 4 runner wheels did you needed to do any modification to install them or they just fit easily ?
@mypoleinurhole
2 жыл бұрын
Just need mag type lug nuts with the nissan thread pitch. Can get them off Amazon
@jretkl7959
2 жыл бұрын
@@mypoleinurhole so you didn’t need to cut anything or things like that ?
@jretkl7959
2 жыл бұрын
@@mypoleinurhole does the nitro drop 2 lower it down a bit more , because I’m tryna get those type of shocks too
@mypoleinurhole
2 жыл бұрын
@@jretkl7959 they don't drop the truck. Just the right height for lowered trucks and stiffer than stock so you don't bottom out the shock
@mypoleinurhole
2 жыл бұрын
@@jretkl7959 no. I didn't cut anything on my truck
@mava78
2 жыл бұрын
What front lip is this?
@mypoleinurhole
2 жыл бұрын
1st gen. S10
@adhippie21
3 жыл бұрын
She fine bro
@WhoopAzzRacing
3 жыл бұрын
do you have the link for the racing tor-sen bars?
@mypoleinurhole
3 жыл бұрын
4th link in the description
@jimmywilliams1223
3 жыл бұрын
Most people would want to do more. Leave it alone. The truck is super clean and looks great like that. Leave it alone.
@mypoleinurhole
3 жыл бұрын
It could use a redrill. And some slight body and fresh paint. Its harder to pick up on camera with the white paint. It was a old bug spray work truck but mostly sat in a garage as a back up truck so very low mileage. But PO had it resprayed and it has lots of error and over all a bad job if you really stare at it, But it looks good from 10ft away lol. Plan to keep this truck for life
@jimmywilliams1223
3 жыл бұрын
It could use a re-drill, but does it need one. Most likely not. I have seen too many people destroy their vehicles because that just want this or they just want to do that. You truck sits great. If you want to paint it, do it. Just know that the re-drill will turn into tubs, then air suspension, then trash because you won't be interested in the truck anymore. Paint the truck, do some nice interior work on it then leave it alone and enjoy. Allow folks like me the opportunity to be envious.
@mypoleinurhole
3 жыл бұрын
@@jimmywilliams1223 thats probably where I'm gonna stop with this one. I thought on the idea on bags. But this chassis is too clean. Will get a different truck if I ever wanna do that and any other crazy ideas. But yeah I'm probably just painting this one, sound deadening and a few other things to clean it up.
@Izreal3345
3 жыл бұрын
Looks dope bro 😎
@nathankoroush7918
3 жыл бұрын
So clean. Are those 4 runner wheels?
@mypoleinurhole
3 жыл бұрын
Yes. Trd version
@nathankoroush7918
3 жыл бұрын
@@mypoleinurhole I have a set of Sequioa wheels I will be installing on mine.
@sharktooth1985
3 жыл бұрын
Hell ya! Fukn SicK got mine bagged but want one just like that 👍👍🤟Love it!
@IsaiahnElenafr
3 жыл бұрын
Pathfinder grill conversion? Good looking truck👊
@mypoleinurhole
3 жыл бұрын
Yes it is. And thanks
@ALLWORKNOPLAYnetwork
3 жыл бұрын
CLEAN
@mypoleinurhole
3 жыл бұрын
Thanks 🤙
@builttolastmaximus108
3 жыл бұрын
I have the same wheels on my d21 where did u get those center Caps wanna get rid of the Toyota emblem
@mypoleinurhole
3 жыл бұрын
Just cheap filler caps from ebay glued on. Just remove the toyota emblem
@builttolastmaximus108
3 жыл бұрын
Thanks brotha I got them I just didn’t like the little holes that get exposed after taking The emblems off
Пікірлер