ohhh, so that's what the thing is for! Thanks! 13 years later, and your video is still helping. 😁
@Lewisusa11
6 ай бұрын
I was not aware I was supposed to add a rod between the two gauges, I just always put one at each end. Just found out I need to replace the motor in my grizzly G1017, which is 30 years old. Cutter spins but not the feed chain side. :( Ugh!) great video, thanks!!!
@flagman40
2 жыл бұрын
Where can I get that tool?
@nigealandrews2337
2 жыл бұрын
You was simple understanding an quick good job
@abbasfurniturehouse3737
3 жыл бұрын
👍👍👍
@christopherparrisjr.3146
3 жыл бұрын
This deserves more views!
@kimonecampble1166
4 жыл бұрын
Where can I get the blade to perches
@Harris4465
4 жыл бұрын
This was great. I am a bit uneasy doing stuff like this for fear of making it worse than when I started. This is very helpful.
@tessaheart9777
4 жыл бұрын
amazing
@gurmailsingh8900
5 жыл бұрын
Sir how price to 10" thikneser
@SinCityWoodworkers
6 жыл бұрын
This is a Bridgewood 24" planer
@tomtpace87
6 жыл бұрын
What type of planner is this?
@jrx2662
6 жыл бұрын
great video you see the whole thing up close!
@faw3511
6 жыл бұрын
This gauge sets the knives parallel with the cuttinghead, not parallel with the planer table. Sometimes it's necessary to set the knives higher on one end with a dial indicator jig to square them with the table.
@raymondbunkofske4702
3 жыл бұрын
It depends on the planer. My Jet has a separate adjustment to set the cutter head parallel with the bed.
@MAGAMAN
7 жыл бұрын
Adjusting these aren't really difficult, just tedious. You should only tighten the two center bolts first, then check, then tighten the outer bolts. You should also wear a glove on the hand you are using to move the blade. Also, when tightening the blade, always pull the wrench away from the blade, never push towards it. If you slip while pushing, you are going to have a really, really nasty cut.
@moneycounsel6619
8 жыл бұрын
Thanks!
@G3RR1TJVR
8 жыл бұрын
I have the planer, but do not have the tool to determine the height. I bought a tool that can be adjusted to the correct height, but I do not know what height to set it to. Could you perhaps advise what the correct height is?
@TyCetto
8 жыл бұрын
Normally, if the knife is ground to the normal cutting angle, you should see less than a millimetre of the flat side of the knife body above the cutter head surface. Never place the knife so that the ground bevel is 'drowning' under the edge of the groove where the knife is sitting.
@allenhunt3070
9 жыл бұрын
I appreciate your posting this video. Really helpful.
@TitusLivy777
9 жыл бұрын
Helpful! Thanks!
@robira1313
10 жыл бұрын
What make is this jointer? Would the process be the same for a Ridgid?
@pagnicinematography
10 жыл бұрын
Great video thanks for posting.
@davidclinkbooks
10 жыл бұрын
Hello: This looks exactly like a Delta JT360 6" jointer I just inherited. It was afloor model and did not come with the bars with the 4 bolts in it. I bought the bars but Delta no longer sells the bolts.. Can you tell me their size? Delta rep thought they were 1/4"x28x3/8", can you verify so I know what to buy to install my blades?
@cneesen
10 жыл бұрын
Thanks for posting this video. It was helpful. I have an old Walker Turner Jointer and am getting set to replace the blades. It's a little rusty, and the WD 40 needs to settle in.
@philrichmond7567
11 жыл бұрын
Cool
@m4chschnell
11 жыл бұрын
do you find that when tightening the bolts the angle of the blade to head causes the balde to drop a bit . If you do I have started using magnets to hold the blade up real;ly tight against jig and tighten all bolts centre first and outer edge last . When you tighten them up check wth a feeler guage to see if they have moved
@1968DieseL
11 жыл бұрын
I just learned how to do this and, you shouldn't put your string on the same spot at each end to get the proper width
@wmcrash
12 жыл бұрын
what model planer is this?
@SinCityWoodworkers
4 жыл бұрын
This is a Bridgewood 24" model, bought back in the 90's. Great tool!
@stairman2
12 жыл бұрын
I have the same planer, and setting tool. But Where did yu get the springs? Mine didnt come with them? Seems like a easy way to set them.
@Yawles
7 жыл бұрын
stairman2 I went to a local farm & fleet store, or Menard's has springs as well. make sure you know what size. I got springs that were just barely under 1/2" x 1" for about a buck each.
@tomtpace87
6 жыл бұрын
What type of planner is it?
@customcraft123
12 жыл бұрын
your video really helped me, you answered all of my questions. thanks
Пікірлер