My mechanic had to replace my throttle body. 2006 Mazda 6s is what I have but yeah I had to replace the throttle body
@isakwilkinson2491
3 ай бұрын
Add my mechanic replace the battery for me and it gave him a rough idle and he left the car running for about 20 minutes and turn on the AC for about 20 minutes and let the computer relearn everything
@sanity114
9 ай бұрын
Reset idle..
@codywild4013
Жыл бұрын
Mazda 6 IAC Idle Speed Motor 2.3ltr L3 GG Hatch & Sedan 2002-2005 that’s what u need to replace
@omarauguiste5576
Жыл бұрын
Just change the entire pump system. Not just the pump. I spend so much money trying to figure this out. Change spark plugs, shuttle body and so much more. Some said it was my computer but at the end it was so simple. On the fuel pump had a part with a whole. It tends to block. Trust me on this. Also i change the cam shaft sensor. This two things was what fix me up after two years
@frankkoehler6554
2 жыл бұрын
I had similar problem with a 2005 mazda 6 if you look at your mass airflow plug or unhooked it or someone else did make sure it does not have any bent over prongs on the plug or if the plug is plugged in all the way as far as it will go on mass air censor that would explain rough idiol and no throttle
@nathanwatts730
2 жыл бұрын
Sounds like it is the MAF/MAP sensor get MAF cleaner and it is connected to your air box spray it clean let it dry
@brandonmartinez4001
2 жыл бұрын
I have the same problem with my 2004 Mazda 6 2.3l it stays right under 1000rpms I changed my my mass air flow sensor and still idles I don't mind putting money into my car I just wanna know what could be the issue
@itsnickbrooo4577
3 жыл бұрын
My car has kinda the same issue I have bad missfires when it's cold out and at idle and leaving from a stop it dosnt die but its close other than that if it's hot out car runs fine other than coming from a stop my car drives normal from 10 miles an hour all the way up to 80 cars perfectly fine I've already changed spark plugs spark plug wires distributor coil PCV valve PCV hose mass air flow sensor and clean my intake manifold and new intake manifold gasket and cleaned throttle body
@darkknight9875
3 жыл бұрын
Give a complete clean and tune up plugs ignition coils your also going to needing the upper pluem gasket because your are going to be taking off the egr valve and the throttle body motor mass air flow cleaner throttle body cleaner try not to play with the butterfly wing do all that and you be in great shape including an oil change
@evoospeed
3 жыл бұрын
Hey Thomas I have the same car did and spend lot of money on to it i don't have a big issue but i still concern on some of them, one of them that when the engine is hot the car starts little bit weird, and while i do a parallel park with auto trans on reverse and i am using power steering the car does a little bit of crazy idle when i steer my wheel on idle and going back without pressing gas
4 жыл бұрын
Ur throttle body is going out
4 жыл бұрын
It’s gonna be ur throttle body trust me
@omarchavez6603
4 жыл бұрын
Selenoide
@theneptune2011
5 жыл бұрын
mazda has a recall for this computer get confuse when weak or dead battery,
@flipztuh24
5 жыл бұрын
Looks like you got a misfire and fuel ratio problem.
@richardmendez3972
5 жыл бұрын
Check the throttle body actuator is bad on you trust me and good and that reply if you runs good again
@CarNRadio1
5 жыл бұрын
Iat.
@gratefulaya192
5 жыл бұрын
Clean off your connections to the starter and alternator
@sigaming7544
5 жыл бұрын
You guys need to remember to maintain your cars. Especially mazda. Oil change regular and new battery, and check on altinator a lot
@jenellegriffith6792
5 жыл бұрын
I have a code for IAC valve but it has none. Is the IAC located in the throttle body?
@JohnathonMyers
5 жыл бұрын
IAC code = remove and clean throttle body with Carb Cleaner and plastic bristle brush (like tooth brush or plastic mech brush), both sides of throttle body, do not move the plate by hand tho
@legendegreene3121
5 жыл бұрын
What was the problem . Mine is shutting off and wheel is locking up . I’m only able to start car in neutral . Please help !
@RexiLCS
6 жыл бұрын
Any updates on this from anyone that got it to work? I have had this issue since april until october, until it died repeatedly and would die will driving. It is in way worse mechanical shape, but what did you guys do? Im getting a computer for it to see if that helps, but my mechanic doesn't want to do timing chain work so yeah.
@TheSlayer668
6 жыл бұрын
Henry Romero mine was the timing so if not that check your sparks and/or read into the comments I got a lot of people that got this problem I recommend getting rid of the car because after I got it done it died again so don’t waste your time or money bro that’s my opinion
@RexiLCS
6 жыл бұрын
Thomas Walker yeah thank you that’s what I’m thinking of doing tbh but yeah tyyyy!
@xfiles5319
6 жыл бұрын
I have a 2004 Mazda 6 2.3L and I’m having sort of the same issue. My car starts and if I don’t mess with the throttle the car will die and once I let go of gas, the car dies. The motor sounds great tho. Anyone got any advice?
@kashi9447
2 жыл бұрын
@KeSean Woods on mozda common issue is vaccum leaks, spark and timing
@kashi9447
2 жыл бұрын
@KeSean Woods Dude I had same issue as him and I had a off timing and a vaccum leak i have a 2003 Mazda6 2003 4cyl 2.3L
@sylviauklondon2259
6 жыл бұрын
got Mazda 6ts, 57plate.. on every traffic light or when slow down car turn off ..like blue motion.. less than 1000/rpm turn off.. what's the problem.. thanks
@tonyjackson9645
3 жыл бұрын
Pvc valve and hose
@stevenmiravete578
6 жыл бұрын
Go to the channel cris fix and he explains what is going on
@PrinceHollieTalk
6 жыл бұрын
Did you figure this out I'm having the same problem
@danieldkperez7479
6 жыл бұрын
did you fixed it ? im having the same exact problem
@dmcpherson1319
5 жыл бұрын
Might be an oxygen sensor
@cancakruso
6 жыл бұрын
It seems that you need a new purge canister valve. When you are cranking, the PVC cannot keep the optimum fuel flow. Did you get a P0455 error code?
@leninrob898
6 жыл бұрын
I had the same problem and changing the ignition coils helped but now the problem is when I drive it it hesitates to much only getting a top speed of 45 to 50 mph anybody have an Idea of what it might be would greatly appreciate it 😄
@loisjules4305
5 жыл бұрын
The mazda needs to relearn its idle so you have to idle foe 20 min. No accessories on and then turn ac on full fan let idle 15 min. This lets computer adjust the air flow gas flow and learns about itself again. Hope it works.
@jonrodriguez6973
2 жыл бұрын
misfire with one of the cilynder
@jonathanjohnson3193
6 жыл бұрын
Check the IAC if that's not a bad check the PCV. Check for any vacuum leeks as well these are easy cheap things that I probably could be if that's not it see if the throttle is gunked up where the air comes in passed the sensor
@rumbogrivian3350
6 жыл бұрын
how did you fix your AT problem
@danielperezcardona7676
7 жыл бұрын
clean valvule EGR
@richardmendez3972
5 жыл бұрын
Not sr you bad is the throttle body actuator
@coltonpool2347
7 жыл бұрын
A little late but, if anyone else has a problem like this it may be the Idle Air Control (IAC). A hose comes from intake to the IAC. instead of the throttle body controlling the Idle certain Mazdas have this IAC. Check that and see if it helps.
@TheSlayer668
7 жыл бұрын
Colton Pool Mazda 6 base model doesn't have an iac but the speeds do good luck to everyone with this problem but just read the comments we got lots of answers here for you guys
@josephsaliba4035
6 жыл бұрын
Thomas Walker hy man i have a stalling problem with my mazda 6 v6 2004 3.0L engine what do you recommed ? My RPM does go over 2 even with full gas
@christopherdemmons4119
6 жыл бұрын
Thomas Walker how’d you fix the AT. We got the same car bud, I need this answer lol, btw I also get a flutter on start up, and I don’t know why.
@analdobissoon3916
7 жыл бұрын
I'm getting same problem
@TheSlayer668
7 жыл бұрын
Analdo Bissoon check your timing chain check to see what codes are thrown and let me know glad to help
@analdobissoon3916
7 жыл бұрын
Thanks
@Xcampp
7 жыл бұрын
mines is doin the same thing N i got the mass air flow sensor and it still does it HELLPPP MEE
@TheSlayer668
7 жыл бұрын
Erika Gregory timing chain you'll need a new one
@richardmendez3972
5 жыл бұрын
Trust me is the the throttle body actuator is baddddd once again trust me is the black cover in the throttle body inside have like little raps whit electronic contact remove the brushes inside but dont brake nothing and clean whit alchohol or contact cleaners and you runs like new. Trust
@russellcarnes2566
3 жыл бұрын
@@richardmendez3972 i just replaced my thermostat, mass air flow censor , patched my radiator , and am doing oil change now. Car has a hard time at staying at the proper idle. I have to rev. The engine in neutral before changing from park to drive and same with park to rev. I. Think i have a leaky head .... Think a possible head gasket leak might have warped the head??? In short " the damn thing wont stay running! 🤔 its my mothers car and she cant have faith in this car nor can i...
@theasualt6759
7 жыл бұрын
Just change or check the mass flow air sensor is attached on the top of air filter
@brandonmartinez4001
2 жыл бұрын
Changed that with a new one but still idles
@mrcordova9442
7 жыл бұрын
my car is doing the samething. how do i fix it?
@TheSlayer668
7 жыл бұрын
Isaiah Cordova timing chain possibly fuel pump but mine was timing chain
@mrcordova9442
7 жыл бұрын
Thomas Walker so my car revs like yours but the car stays on .
@TheSlayer668
7 жыл бұрын
Isaiah Cordova have your timing chain looked at and if that not the problem check your ignition
@TheSlayer668
7 жыл бұрын
Or your fuel pump
@TheSlayer668
7 жыл бұрын
Need help just comment got it all fixed and I know all the problems so just leave a comment and I'll be glad to help
@meade48162
7 жыл бұрын
Thomas Walker my car is having the same issue. Was your fix simply to replace the timing chain or was there more to it than that? i am hearing some people suggest a throttle boddy issue -??
@TheSlayer668
7 жыл бұрын
Mike Meade nope I just did the timing chain and it ran great after that but look to see if you need it replace because mine was fairly new
@meade48162
7 жыл бұрын
So yours was fairly new but it still needed to be replaced?
@TheSlayer668
7 жыл бұрын
Mike Meade no I didn't have to replace mine
@bradleyrussell1741
7 жыл бұрын
so what fixed your issue
@matthewgarcia6746
7 жыл бұрын
how did you fix it mine is doing the same thing right now
@jeremytalbot177
5 жыл бұрын
Did you fix your mazda 6? I have one l Also
@RedBull_0130
8 жыл бұрын
My 2004 Mazda 6 speed 3.0l did the same. I got it fixed. There's 3 plug under the motor cover and one of them was loose as soon as it clipped in the car was running good and I also replace my throttle body. Now my Mazda runs new and better than it was before.
@josephsaliba4035
6 жыл бұрын
Jose Torres hy man i have a stalling problem with my mazda 6 v6 2004 3.0L engine what do you recommed ? My RPM does go over 2 even with full gas
@zwangaramalamula530
6 жыл бұрын
the plugs??Which one because my car is givin g me the same problem
@legendegreene3121
5 жыл бұрын
Was the car shutting off on you while driving ? And wouldn’t start back up ?
@marleyemmond7869
8 жыл бұрын
try the egr valve
@al5037
8 жыл бұрын
I'll give you a good advice, replace the engine for a 2006 Ford Fusion engine and you won't have any problems, Don't even bother in fixing it , why you may wonder,? here is why, you'll save money and headaches, this Mazda engine are poor quality, Ford company made them so weak that way Mazda would get a bad reputation. I replaced mine like two months ago. Now my car is running stronger than before
@al5037
8 жыл бұрын
Ramon 357 1974 I've spent around $1100, I paid $600 for the engine with 155k on it and I paid someone that brought it to my place, I spent the rest in all the fluids, some gaskets that the car needed , I also bought some tools and and a manual that this job would need , but you also can rent them out, I did all the work by myself, well my wife helped me sometimes lol it took me like 3 weeks to get it done, it could've been less time but you know you gotta work to be able to buy all that.
@al5037
8 жыл бұрын
Ramon 357 1974 No problem
@TheJessemull
7 жыл бұрын
not a Gm engine it is a Ford engine you just replaced it with the same next generation ford engine
@al5037
7 жыл бұрын
TheJessemull my mistake is not gm engine
@peternovak5612
5 жыл бұрын
@@al5037 I have 1.8 petrol engine that is sold in Eu , this engines are great if looked after , i have 180.000 miles on my car. I did engine rebuild for 850 dolars becous it was burning oil other then that i had no problems.
@theoretical-b2f
8 жыл бұрын
IF YOU FOUND ANY SOLUTION PLEASE CONTACT ME MY EMAIL [email protected] BECUASE I HAVE THE SAME PROBLEMS
@kiyotabuchi8758
7 жыл бұрын
look at the pcv hose , it is probably split . spray a little brake cleaner around the lower part of the intake manifold when its running too see if has a vacuum leak
@TheSlayer668
8 жыл бұрын
Thank you it runs now and got timing belt too that's for the help!
@trevenwright5465
8 жыл бұрын
i have the same problem now, what cause it to idle poorly?
@matthewgarcia6746
7 жыл бұрын
Thomas Walker how did you fix it
@TheSlayer668
7 жыл бұрын
Timing chain and worked fantastiy when we were done but then I sold it because it it wasn't worth pouring my money into the piece of crap
Пікірлер