Caverntwo
Hello World!I'm a game/software/web dev from Austria. On this channel, you see what I do in my free time!
I started this channel focusing only on 3d-printing in 2017 when I was still in high school. As I grew up, my life changed too, and so did my interests. Because of that, nowadays, 3d printing is a tool to create stuff, and not the main focus.
Be ready for the unexpected. There might be videos about software development, 3d designing / 3d printing, as well as building, designing, fixing, and restoring electronics, cars, and even buildings.
I share content in the hope that it is helpful. I'm no professional in any way and therefore cannot be held responsible for the correctness and anything going wrong on your side. You use my content at your own risk!
For questions, leave a comment or contact me directly!
Thanks
- 5:17
- 4 жыл бұрын
MKS TFT Firmware Upgrade & Customizing
- 3:16
- 4 жыл бұрын
Invert Stepper Motor Direction - 3D-Printing Basics
- 5:30
- 4 жыл бұрын
3D Printed Christmas Light Displays
- 3:39
- 4 жыл бұрын
Level Your 3D-Printer - 3D-Printing Basics
- 11:15
- 4 жыл бұрын
FLSUN Cube Initial Review - Large, Awesome but DANGEROUS!
- 2:20
- 5 жыл бұрын
Fix Layer Shifts
- 12:26
- 5 жыл бұрын
Get Started With Cura | Beginner's Guide | 3D Printing Tutorial
- 5:44
- 5 жыл бұрын
Flash Bootloader on 3d Printing Controller
- 2:49
- 5 жыл бұрын
Fix Noisy Fans on Your 3D Printer
- 4:49
- 5 жыл бұрын
Diagnose & Fix Z-Axis Issues on 3D-Printer
- 10:26
- 5 жыл бұрын
3d-Printing Vector Graphics - Tutorial
- 5:59
- 5 жыл бұрын
Christmas 2018 - Printing Last Minute Prints!
- 5:26
- 5 жыл бұрын
Create a Wearable Cubone Skull - Halloween 2018
- 13:29
- 5 жыл бұрын
Anycubic Utrabase on Anet A8 - Full Installation Guide
- 17:04
- 5 жыл бұрын
Dual Color Printing with a Single Extruder Machine
- 10:18
- 6 жыл бұрын
Simple Door Lock - 3D-Printing and Arduino Project
- 5:42
- 6 жыл бұрын
Channel Update June 2018, New Workshop, New Schedule
- 8:23
- 6 жыл бұрын
Anet A2+ Upgrades
- 9:19
- 6 жыл бұрын
JGAurora A5 Review - Good Printer for $350!
- 11:12
- 6 жыл бұрын
Anet A8 Dual Extrusion
- 3:41
- 6 жыл бұрын
Multi-Color Prints with Single-Color Printer
- 7:24
- 6 жыл бұрын
Filament Run-Out Sensor on Your 3d-Printer
- 3:59
- 6 жыл бұрын
Anycubic Kossel Upgrades
- 5:08
- 6 жыл бұрын
Anet A8 Controller Upgrade (Arduino Mega + Ramps)
- 2:55
- 6 жыл бұрын
Anet A8 - Heated Bed Insulation
- 10:11
- 6 жыл бұрын
Anet A2 (A2+) Initial Review
- 3:59
- 6 жыл бұрын
Anet A8 Marlin Firmware
- 5:41
- 6 жыл бұрын
Пікірлер