I have to say this. Why use this method? Uneven job. Should use a circular saw.
@umac01
3 ай бұрын
Great job, but you should drill a single hole right through the centre of the hole from the inside to the outside to give you the reference for the outside hole centre. Just a thought.
@Hew.Jarsol
6 ай бұрын
Nice one mate. Better for the DIYer as renting or borrowing a core drill is a pain in the arse! PS where are you mate you've not be on in over 7 years..?
@tomm.h7324
8 ай бұрын
Cheers for the video. Very helpful. The tips are great 👍
@philipsturtivant9385
8 ай бұрын
Second video I've looked at today that doesn't cover the one step in the process that I'm looking for - assembling and mounting the interior components of the vent kit to the inside of the house wall!!
@neilkanagaratnam7445
9 ай бұрын
Excellent thank
@sboy1955
10 ай бұрын
Nice job 👍🏼
@mbak7801
10 ай бұрын
WOW that is a hard work way of doing it. I use a 3/8 diameter long drill bit to make a pilot hole from the inside sloping downwards by about 10 degrees right to the outside. There will be a little spalling on the outside brick but that does not matter. Then I use a 4in drill bit with its own internal 3/8 bit which sticks a couple of inches past the end to follow the pilot hole I have already made. The hole is very neat and exactly to size and as it is done in a single action the alignment is exact. Push through solid pipe and then screw covers etc and fill to prevent water ingress. The large drills make the job much quicker and the finish neater. They are not that expensive, I think they can probably be rented but my set includes additional sizes for sink/dishwasher drains and armoured electric cables. It is amazing how many holes you end up drilling into a house.
@michaellakeman4208
6 ай бұрын
£100 plus to rent a drill powerful enough for a day.
@ColinDH12345
11 ай бұрын
07:30 Should explain that the external vent has a top. You cut over where you reversed it off camera ;-) No harm in explaining these tripping points to people.
@fedguy9182
Жыл бұрын
Why not use an SDS diamond core bit for a clean hole
@suburbanappalachia4308
Жыл бұрын
Very nice Cliff! Good job.
@victornaja7927
Жыл бұрын
what size drill bit is it 1/4
@charliehitchen5263
Жыл бұрын
Nice, clear and no BS. Perfect.
@1fasrimport
Жыл бұрын
Great video!
@JToddJeep
Жыл бұрын
Using a vac as you drill will greatly mitigate the particulates and make for a much more tidy workspace. youtube.com/@toddandemysadventures2045
@ruthadams2413
Жыл бұрын
I'm in the US and I need to do this for my dryer since the past owner put a deck board in front of it. Great info, thanks
@JL-of3db
Жыл бұрын
Just seen this, is there a way of checking there are any pipes in the wall or wiring before starting to drill?
@FOODKINGUK
Жыл бұрын
Well done 👍 brilliant video 🎉 the outside cover has it got air flaps so that you don’t get anything coming in spiders mouse etc
@housesforsale6892
Жыл бұрын
drilling like this seems better then using drill core bits which take for ever
@UberWagen
Жыл бұрын
PVC dryer vents and that type of transition ducting are actually against code in the U.S. now. Builds up static electricity as lint tumbles across it and can cause ignition. Not to mention, that flimsy hose tears and will cause leaks into that room. Goes without saying, but just in case: ABSOLUTELY, DO NOT USE THESE MATERIALS WITH GAS POWERED DRYERS.
@22kylejones
Жыл бұрын
Buy a core bit.... also Plastics for a hot exhaust seems like a bad idea
@voiceofjeff
Жыл бұрын
Clear and simple explanation of how to get it done. I think an important thing to remember is to try to locate a dryer exhaust as far away from an outside A/C unit as you can. Lint blowing out of the dryer vent can clog up an A/C condenser unit in no time at all! Greetings from the USA. Enjoyed your video. Thanks for sharing.
@gm08351
Жыл бұрын
how do you check for pipes/wires ? or is it just a luck game
@jesstaylor2737
3 ай бұрын
A stud detector will do.
@Poekieman
Жыл бұрын
That was useful and instructional. Drilling a big hole in a wall using just regular tools. Thanks.
@twobluebirds5647
Жыл бұрын
This was great, thank you. How did you know you were drilling exactly dead centre through the exterior brick though? Thanks!
@michaelhenly4371
Жыл бұрын
Thank you. Great information.
@adamharding365
2 жыл бұрын
just pop a pilot bit through from the inside , alot easier
@SwingAndSway245WBC
2 жыл бұрын
Very nice. The only thing I would change is using an aluminum flexible tube from the dryer to the external tube. In many places plastic flexible tubes are not to code.
@kimlam1164
2 жыл бұрын
big and very BIG Thanks mate
@christopheradolphe
2 жыл бұрын
Thank you sir. That was the exact tip I was looking to install the duct of my kitchen hood. May I know what is the name of the fitting you installed outside so that I can look for that at the hardware store. Thanking you in advance.
@tannerc900
2 жыл бұрын
Would this method work for stucco as well?
@randallallen5331
2 жыл бұрын
Now if only he would’ve used code approved transition material for vent line he would have been perfect
@elainev670
2 жыл бұрын
Thanks for this video
@Shazzkid
2 жыл бұрын
Defeated the purpose drilling a down facing hole if you end up sealing it up on the out side wall side. Wheres the water gonna go, it can't escape? You sealed it up?
@jesstaylor2737
3 ай бұрын
That is for a vent not a condenser pipe the vents don't have any moisture pass through from the inside. the sealant and down sloping pipe is to reduce the risk of any external moisture entering the pipe or wall through the whole like heavy rain for example.
@jackflash5659
2 жыл бұрын
This is a proper tutorial. 2 thumbs up! Cheers from Canada!
@shia_labeouf
2 жыл бұрын
Absolutely awesome stuff. Well edited to keep from being overly long but without skipping any important steps. Some great advice on what tools to use and the tips about putting a screw in to grip and drilling the hole slightly downhill are excellent. Finally, a likeable and clear host. As someone who's just bought their first house, this was an easy subscribe!
@liverbird46
2 жыл бұрын
Excellent
@andyxox4168
2 жыл бұрын
‘👍Job done’… now time for the wife to tidy up … 😂😂😂
@jboyd7327
2 жыл бұрын
Excellent instructions but the diameter should be of the tube not the connection fitting on the outer/inner wall which is smaller.
@ilricettario
2 жыл бұрын
Only observation it would definitely be better to buy, or borrow yourself a diamond core drill set to make the hole.
@ilricettario
2 жыл бұрын
Excellent, a commonsense, practical demonstration of how to make your calculations for a successful installation.
@sillygirl1139
2 жыл бұрын
Brilliant, thank you.
@mattomite9097
2 жыл бұрын
Awesome. video. I was scared about drilling into my brick exterior but you made me want to attempt it. Thanks
@moneyfornothing3264
2 жыл бұрын
Jesus Christ Ivor. That’s an incredible job. Holy fuck you made it look so easy.
@TruthSeekerAi
2 жыл бұрын
GREAT DEMO
@mattf1986ut
3 жыл бұрын
I so prefer DIY videos like this, straight to the point clear concise giving you the info you need
@hexhex7220
3 жыл бұрын
Thanks so much for the brilliant little video. Now I think I can do our install!! (Love your accent)
@davidcoleman6032
3 жыл бұрын
Brilliant video, I now have the inspiration!🙂👍Many thanks!
@myfaceback100
3 жыл бұрын
You saved me getting a core bit as i only have to drill for two vents long drill bit is much cheeper Thanks Great video
Пікірлер