Thank you so much!! Works as well with the ProXpress c3010nd..🎉 😊
@SR-pr2xz
20 күн бұрын
beautiful. works on CLX 4195N which uses the same drum module. thanks
@benzder90er
24 күн бұрын
It's easier to bend it a little with needle-nose pliers.
@mohamedsakka2338
Ай бұрын
aww im so happy he even told me to use a tweezer so i dont hurt my fingers : )
@spezibibo
Ай бұрын
Fehler war #A1-4112; Filz von der Spule durch ein Stück Möbelfilzgleiter ersetzt, nun kommt #A1-4111. Dünneren Filz gewählt undnun ist es gut. Bei der Gelegenheit (Gehäuse offen) kann man auch die Lithiumknopfzelle tauschen. Danke für das Video, Gruß Spezibibo. Error was #A1-4112; Felt from the spool replaced with a piece of furniture felt glider, now comes #A1-4111. Chose thinner felt and now it's good. You can also replace the lithium button cell at the same time (case open). Thanks for the video, regards Spezibibo.
@efecand.8128
Ай бұрын
Teşekkürler. Köpürtme fonksiyonu tekrar çalışmaya başladı.
@emilyc9822
Ай бұрын
Jack hi I’m from Malaysia. I saw your Nespresso aeroccino fix but I don’t know which screw to unscrew 😂 have been trying for days. Hope to receive your reply 🙏🏻 please help me (I really want to froth again 🥹🥹🥹)
@emilyc9822
Ай бұрын
Thanks for the tutorial. But My screw is like a triangle screw, which head can fit it? 😅 have been trying for hours but NTG fits
@xCain69x
2 ай бұрын
Cheers mate great help 💪 the fuse had gon on mine!
@laurenciusdjauhari5842
3 ай бұрын
Thank your very much for your video! I followed your clearly explained steps and managed to fix our red light blinking broken aerocinno 3. Reversing the polarity indeed works. The milk frother is working beautifully again! Really helps!
@ugoallen1
3 ай бұрын
Thanks a lot for this video. I fixed mine easily because of this video
@MCAJ-zs1sr
4 ай бұрын
Great tutorial! Also very appreciated that you left the part where it didn't work. Helped with the understanding of all the aspects that needs to be considered. And you saved me (and the environment) the cost for a new printer. And for me it was the small rubber pillow that had slide down just a little bit. Pushed it back up and had to experiment on how to keep it in place with a small piece of electrical tape. The construction seems to be very sensitive to the thickness... But thanks to you're video I figured even that out.
@hcy97
4 ай бұрын
The frother motor no longer spin. I swapped the black and red wires and now it works again.👍
@PatrikJohanssonSNATRA
5 ай бұрын
Thank you for that very clear video. It helped me fix the same problen in 5 minutes on my printer. I like that you included your fail with the too thick buffer so we did not need to do the same thing.
@damianamamoo2438
5 ай бұрын
Thanks so much Jack, you saved me replacing my 6260 printer with your clear instructions. I just added a little elastoplast tape to thicken the black pad and it did the trick. 🙂
@sammylim3387
5 ай бұрын
Hi Jack, when you test the thermal switch while on the board is it close or open?
@user-jb5oy4nz6n
5 ай бұрын
Appreciate very much your help, and I'm everything but a geek. Thanks a lot!
@briansmith1098
5 ай бұрын
Mine does not heat, any ideas?
@RetroKrazy
6 ай бұрын
Thanks! Seems I had a similar issue to @mascot4950 where the pad had sliped down. Moved back into place however I also tweaked the arm so it contacts sooner, meaning if the pad fails it may still keep working and just get noisy 😆
@junksails814
6 ай бұрын
Worked exactly as dwsceibed - purfect and wirh many thanks
@mascot4950
6 ай бұрын
Thank you so much. Almost seven years later, this is still helping people. I've had my CLP-680DW for almost exactly 8 years now, and since I'm still on the original toner cartridges I figured the error couldn't really be due to some worn down part. Ten minutes later, and it's fixed. In my case the pad had slid out of place, and just gently pushing it back into place with my fingernail sorted it out.
@user-de4em6ti9y
6 ай бұрын
Hi, i succesfully reverse the polarity of the magnets and my whisker starts to spin again (previously motor dead, not spinning at all). But now it only spins for about 4-5 seconds and it stops with red light blinking. Can anyone point what i possibly have done wrong? Thank you.
@timstone869
7 ай бұрын
Thank you, you were the only one who talked about the motor not working and your fix worked! Well done!
@thomashjelmgren1130
7 ай бұрын
I was able to repair A1-4112 with your excellent viedeo Nobel prize now comes here from Sweden. Best Regards Thomas Hjelmgren Sweden
@user-ee6pp2kr4y
7 ай бұрын
Thank you so much, I can see this video is 6 years old, but it still works! Just had this error on my CLX-6260FW. In my case the foam pad had moved downwards and was not making contact with the arm at all, so I pushed it back up and it's working! Woohoo! That was so easy, took like 10 mins, and it was free. My heart sunk when I first googled the error code and saw "motor failure". If the pad moves again I may replace it but now I know where to look. Thanks again, this is awesome.
@maxp5842
7 ай бұрын
the world bows down and thanks you for your service ❤
@ferdinanddekeersmaeker1686
8 ай бұрын
Thanks , I pull it out of eath other pull the switches in and out . And back as new . Finkers cross
@joeridevlieger5996
8 ай бұрын
worked like a charm ! thank you sir
@stevedenning5175
10 ай бұрын
Thank you very much. Fixed. If there's any way of buying you a beer or three please say.
@sorenscholz7281
10 ай бұрын
Thank you so much for this video. It helped me! 👍👍👍
@pierrepavy5058
11 ай бұрын
Thanks a lot my friend
@carolinarego737
11 ай бұрын
I’ve tried this. Couldn’t figure it out how to pull the black and red wires off. Where can I buy a new withe plastic thing where the wires are linked to? 😢
@Darbar_Official
11 ай бұрын
fixed mine! it just doesnt stop automatically but im fine with that!
@bymyself15
11 ай бұрын
Thank you for the guide. Manage to fix mine as well. Had a hard time trying to separate the top section as it looks like it has glue around it. Now I can enjoy my aeroccino again
@michaelweirich5664
Жыл бұрын
Thank you! With your video I was able to repair the printer in less time it would need to bring it to the service shop.
@user-mc3np9yl7k
Жыл бұрын
You are so smart!!! I replaced the pad and my printer is working again! Many, many thanks!!!
@meingoogleaccount3515
Жыл бұрын
thank you so much! My printer is working again. Great!!!!
@UzbekFL
Жыл бұрын
Thanks mate. Such a great video. Repaired my aeroccino too
@dr.peterwiegand9021
Жыл бұрын
Thanks for instructions. It works, but the foam in video was too thick, which results in the loud noice, you hear already in video. In addition bad prints and another error. After taking a foam of half thickness everthing OK.
@Albertojedi
Жыл бұрын
Hello, mine's spinning erratically. Tends to spin for 4 or 5 seconds and stops. I did not catch which tool did you use for removing the two screws. It looks like the Allen kind of, but I doubt those fit the screws.🤔🤔
@andyjame6351
Жыл бұрын
This printer is a workhorse. We have saved SO much money kzitem.infoUgkxciSwynMJ7PnUvvx11rewiu-yFBkZTl53 . I've only filled the ink tanks once and have printed thousands of pages. The color is a little dull, but I will take the cost savings any day. It has trouble feeding envelopes, but other than that, I can't recommend it enough. I'm super super pleased with this printer and recommend it to all my friends.
@ThinkerionStarcraft
Жыл бұрын
Just saved me a lot of money as i just bought and installed all three color toners right before i got the fault... was as easy that the glue on the sponge isolation had sagged a little with time... Just scraped/pushed it back into place and voila.!! Thank you!!!
@TrifidStudio
Жыл бұрын
Thanks for this! You saved me from a potentially expensive service call.
@pietschpictures8818
Жыл бұрын
Samesamesame. Great! Thanks for this video. Printer ist working again, exactly like predicted. Unbelievable
@malevich37
Жыл бұрын
And another one! Thank you! At least 288 printers saved. I don't understand why they used a plastic foam pad.
@user-nd1dh6ju5e
Жыл бұрын
😊 manythank for your VDO It already work
@worksheriff
Жыл бұрын
Brilliant, thanks for making this video. Particularly awesome for showing the problem with the foam being too thick as i definitely would have done that. Thanks
@ariebos7872
Жыл бұрын
Thank you for the clear video. unfortunately it did not work on y maxhine. I also cannot find the thermal fuse like shown in many other video's. the motor is OK (checked) contacts are cleaned but still no luck...😞
Пікірлер