No CO2 is needed for this tank, and anyway the best option is a reactor where there are no bubbles.
@TheSjoerd1998
9 ай бұрын
is the thicksness of the plate 5 milimeter?
@fisherchi
9 ай бұрын
Very nice tank overall. I like the simplicity of your DIY cover. I have a new 72 gallon rimless tank that I will probably do something similar to what you have done. Thanks for sharing.
@xisotopex
9 ай бұрын
very good
@angel27486
Жыл бұрын
Great
@michelleparsons9881
Жыл бұрын
My external diffuser doesn't mist very well, Is it because of the glass lilys? Thank you
@comando8919
Жыл бұрын
I run a atomizer with lily pipes from fzone it work really good Maybe soak it for a while before usage ?
@sergiohenriquedefaria9624
Жыл бұрын
Excellent job
@fabiodeoliveiraxavier4751
Жыл бұрын
Muito obrigado estava procurando um Review desse difusor a um bom tempo
@moraisins
Жыл бұрын
Great video! Thank you!
@jandomingo9806
Жыл бұрын
I just ordered this from aliexprss
@TheresLiterallyNoHandlesLeft
Жыл бұрын
Great video! I have the same product, but after unscrewing all parts and then reassembling for my tank, I have a spring that it not installed. I am worried it is important - do you know where the spring goes? Is it supposed to be inside the lathers screw off cap? I’d really appreciate your advice!
@stoneysscapes7544
Жыл бұрын
Very simple to buy a new one to take apart and carefully find the order , and then it's always best to have a few backups in your hobby !!! GL
@simonemigliorini1146
2 жыл бұрын
where can I buy it?
@jandomingo9806
Жыл бұрын
Aliexpress
@UUIDEARAqua
2 жыл бұрын
Wonderful review, dear, this is Nancy, we are the original manufature of this external co2 diffuser, can i talk with you for more cooperation?😀
@RandB_Aquatics
11 ай бұрын
coorporate with me too please😊😊😊
@ahmadfaisol7496
2 жыл бұрын
Nice review. Are you still use check valve before the diffuser?
@stoneysscapes7544
2 жыл бұрын
Yes it is "very simple & straight forward"= Brilliant DIY !!!! Keeping everything organized is tough but thanks to you I will not waste time trying to find my tools , but now if I could just remember where is the hot glue gun 🤔
@marthanewsome6375
3 жыл бұрын
Why don't you have proper angles for the pipes, because they will compress over time. Clear acrylic wont weaken the light. There is clear over the top of LED lights. Think about it. I use 3ml just fine. You don't need it thick at all, as long as it stays flat on top of the tank. If you get a hair dryer on the bit that is bending and using some heavy books you can flatten it out.
@nithinmohan385
3 жыл бұрын
Thanks bro.This is the video I am looking for 👍
@ikbalantoniolly5292
3 жыл бұрын
Cisod mister
@faishaltanim9096
3 жыл бұрын
I love setup very much... love from Bangladesh.
@_yeahbaby
3 жыл бұрын
I checked the website but only in japanese. Where would one buy one for Canada?
@jandomingo9806
Жыл бұрын
Aliexpress
@nel5826
3 жыл бұрын
It’s recommended that you do not touch the ceramic disk or any ceramic parts on diffusers.
@MrVendeuvre
3 жыл бұрын
Ferme ta g..... !!!!
@wufler28
3 жыл бұрын
The website doesn't work
@adrian-ef3ws
3 жыл бұрын
Nice video, but do you really need CO2 in your tank? You don't have any carpeting plant. Maybe you can lover light and make it more low tech? Especially because you don't have high pressure CO2 system, just yeast or acid DIY. As you know IT is very unstable and a lot of time makes more cons than pros. Best wishes, keep It up!
@solarize1149
3 жыл бұрын
Thanks for the video:-). Where did you buy your acrylic? I've looked at bunnings and mitre 10 but they only have 3mm. Also how much did your acrylic sheet cost? I purchased polycarbonate double wall stuff yesterday for $31 from bunnings also picked up some edge capping to keep it clean. I'm concerned about how much light will get through. 10 or 6mm Acrylic would be my preference for this project.
Пікірлер