Off by hand? Who worked on that engine. I've never had one come off even with an impact wrench at max tank pressure. Always have needed an extension and bar against the floor and bump the starter.
@MacdoNaldi67
5 ай бұрын
That took just bent and broke for me. Had horrible luck with it.
@عليمعادالغديان
7 ай бұрын
kzitem.infoTdUet19Mk3g my way to pull it out
@عليمعادالغديان
7 ай бұрын
@TdUet19Mk3g
@tunerforlife2274
8 ай бұрын
Hey thanks Ima try this
@slowLFX
10 ай бұрын
Damn that car looks like a blast hell yeah
@mulletz_garage
10 ай бұрын
Had a lot of fun with it set up like that. Burned a piston and started from scratch on the car. I’m doing full write ups on everything on the website if you want to check it out MulletzGarage.com
@ChrisC-fr8yu
10 ай бұрын
Let me ask. I tried heating up my harmonica balancer, WD-40, The 3 prong tool, a hammer and still won't budge. Any suggestions? Thanks!
@mulletz_garage
10 ай бұрын
I would use the tool in the pinned comment ( amzn.to/3Q8xZGJ ) instead of the 3-jaw puller. I would also use PB Blaster instead of wd-40. are you using a ratchet or an impact?
@ChrisC-fr8yu
10 ай бұрын
@@mulletz_garage I Finally got it off. Getting it back on was a bit tuff! Lol It's on there Super Tight. Ran into one problem, the bolt broke off. So, I went ahead and put everything back together, and started it .... I monitored the pulley and no budging or wobble. I'll have to Very Soon correct the broken bolt.
@mulletz_garage
10 ай бұрын
@@ChrisC-fr8yu the bolt threaded into the crank broke?? Autozone should have a balancer install loaner tool
@Mr.3Pumps
9 ай бұрын
@@mulletz_garagedo you need a specific tool to install the crack shaft??
@mulletz_garage
Жыл бұрын
Balancer Removal Tool - amzn.to/3Q8xZGJ
@doktorzasinuse
Жыл бұрын
24mm crank bolt socket 🥇 thicker wall socket
@Assertiveman
Жыл бұрын
I reccemond using a tap and die to rethread the hole and a little antiseeze and lock tight on the bolt, torque down with a torque wrench with digital torque gauge and hold for seconds after click done people end up having hard timing after trying to remove a High torque old bolt, and a bolt hasent been removed in a long time it's always good to heat up the bolt first instead of penetrating when you lubricate it doesn't even touch the threads at all metal partial that have broken off of the threads could potentially get jammed while removing and make the process so much horrible so yeah always a impact
@Mechanicaladvan
Жыл бұрын
The song 😂
@fragment2743
Жыл бұрын
Worked perfect W video
@812racing
Жыл бұрын
What rpm’s does this thing build like 5psi of boost at? Or what rpm’s where you leaving at in these videos
@faviang9101
Жыл бұрын
Nice! Installation vid next ?
@mulletz_garage
Жыл бұрын
Products list - amzn.to/3oatYX5
@khalil5908
Жыл бұрын
"promosm" 😑
@uemackay1592
Жыл бұрын
Hello 👋 i have a question and the Internet is giving me mixed answers. I want to replace the front main seal on my gm b207r. I have to remove the harmonic balancer I will use a impact, my question is can i in any way effect the timing of my engine whilst removing or refitting the harmonic balancer. Thanks in advance.
@mulletz_garage
Жыл бұрын
It’s an LS engine? If so, no. Timing can’t be effected at all by removing and installing just balancer and front/rear covers. I’d suggest getting new covers with the seals installed already. Plus, balancer has a key way on the crank that needs to be lined up in order to be pressed on.
@uemackay1592
Жыл бұрын
@@mulletz_garage Its a 2.0T, 4 cylinder petrol engine its maxed at 300bhp without changing internals. Thanks for your advice, I think the reason I got confused is because you are supposed to lock the flywheel with a tool if you use a ratchet to take of the crankshaft pully (harmonic balancer). I will be using an impact wrench so i dont need to do that step. I guess I just figured if you have to lock the flywheel if using ratchet on the crankshaft bolt then it must be because it moves the timing chain? Many thanks, I asked a few people and you are the only one who has replied. I appreciate that.
@mulletz_garage
Жыл бұрын
@@uemackay1592 reason you need to lock the flywheel is because you'll end up just spinning the crankshaft before you're able to get that bolt free
@Hammerback0
Жыл бұрын
Slick Rick Version 2 in red.
@mulletz_garage
Жыл бұрын
John Doc actually bought that first black fourthgen trans am off me years ago. You can see this car in his video "FINALLY BUYING A PROJECT CAR!!!! (not clickbait)" This is old video of the cars last setup. new build can be found on mulletzgarage.com
@zAvAvAz
2 жыл бұрын
is it 10.5:01 the reason i ask i was planning a 355 with this cam and supervic II , or should i use an rpm intake, it is a street camaro 2nd gen. well i was also looking at xr294hr and the 300hr and i shall add slightly more compression with those just wondering how streetable is it with 4.56 gears and a th400 with high stall
Пікірлер