I am putting a 4BT in mine right now, I have 4.89s and 40" Michelin XZLs, plus a disk kit. It should be pretty good.
@justindearborn7275
3 ай бұрын
That’s awesome. Are you running a five speed or are you gonna run a four speed?
@maxloffgren3517
4 ай бұрын
✅
@MoneaKhmer09
Жыл бұрын
so love it and in Cambodia still use it kzitem.info/news/bejne/mKxn2Ix_kJtjbKw
@shanesmaineshop
Жыл бұрын
I have a 66 power wagon with a 251 and i like what you were saying about the oil filtration system. i need to look into that. Thanks for the video and tour.
@justindearborn7275
Жыл бұрын
If it has a little discussion on the side of the block with two threaded ports, it’s a full flow block
@shanesmaineshop
Жыл бұрын
@@justindearborn7275 Where about would i look for them? Thanks for responding.
@justindearborn7275
Жыл бұрын
Lower driver side of the block 3/4 of the way back. It should be like a flat spot with two drilled threaded holes or if it does not have it available it’ll just be a blank plate or threadless holes.
@shanesmaineshop
Жыл бұрын
@@justindearborn7275 awesome, thank you so much for responding i will check that this weekend.
@henryszubielski8601
Жыл бұрын
You have a really nice Dodge! Sounds like you did all of the right things to it for a daily driver. Congratulations and enjoy it!
@X-Appeal
Жыл бұрын
Do you still have m37? I saw you in a bobbed m35a2. Is it yours? You should do a video on it.
@justindearborn7275
Жыл бұрын
Yes I still have the m37 and the bobber
@mrsimpleesarcastik3494
Жыл бұрын
I wonder how a 225 slant six would do in there?
@justindearborn7275
Жыл бұрын
Probably well, it’s way ahead of a flathead stock for stock
@user-nc4cx4gw2z
Жыл бұрын
Do you still have this Chevy?
@justindearborn7275
Жыл бұрын
Yes, except it’s 500hp now
@familiafightclub7407
2 жыл бұрын
What's a value on one of these running and in fair condition? I'm thinking about buying one.
@justindearborn7275
2 жыл бұрын
Maybe 5-7k
@ronalde.wilson7406
2 жыл бұрын
Excellent information. I have a 46 Power Wagon & I think there are related information points. Thanks very much.
@justindearborn7275
2 жыл бұрын
Yes nearly everything but the body is relative this is all relevant information for you
@benelliott8224
2 жыл бұрын
Hi Justin, fantastic set up. I have the same engine in my 1961 Australian dodge truck. And it’s currently running the stock E7T2 carb. I’m going to swap it to the 32/36 as you recommend. I am going to put extractor headers on. Not sure if you are aware but Langdon stovebolts do an attachment that bolt on under the stock inlet manifold and heat it with water from a base connected to thermostat housing to keep inlet manifold hot. Neat little set up for $30. I’m in Australia so probably not going to worry about installing it as we don’t get your winters here. Thanks for doing all that research on the carb set ups. Fantastic information!! Cheers
@michaelyoho4848
2 жыл бұрын
You know what's obnoxious, your video being out of focus so often. I really hope you improved this significantly because I couldn't even finish the video.
@wesleyrawlins
2 жыл бұрын
Hey Justin, thank you for the run down on your M37. My best friend left me his M37 that he had just finished restoring. The first mod I want to do is to move to the 489 ring and pinion set. LOL, the 489s will be my blue rope on this puppy. I am not as handy as you so I would like to sent the differential to someone like Robert Stall to do. Finding the 489s by itself hard to do. Do you have contact info for Bob?
@justindearborn7275
2 жыл бұрын
Unfortunately bob died recently so that service is no longer available through him
@jamesedinger9811
2 жыл бұрын
Want to convert my M37? Let me know.
@justindearborn7275
2 жыл бұрын
Where do you live?
@josedavidsuarezeljure9389
2 жыл бұрын
Did you install disc brakes on it?
@barbaranadeau3878
3 жыл бұрын
Great job. Thanks for the details. Mine has a 6L GM ls, 4.89 diffs, and 9.00x16 bias ply tires on stock rims. Fun to drive with power steering power brakes and automatic transmission. 2000 rpm at 50 mph.
@MrJeep75
3 жыл бұрын
Should of just dropped a 360 in it, been done with it
@MrJeep75
3 жыл бұрын
Driver's seat in stock m37 isn't uncomfortable at all
@MrJeep75
3 жыл бұрын
95 h.p 50 mph
@kevincote470
3 жыл бұрын
I wish I still had my 54' M37...
@timothykeith1367
3 жыл бұрын
And you've had this since you were 12? You can't ever get rid of it!
@tomdamon7208
3 жыл бұрын
Out standing work !
@justindearborn7275
3 жыл бұрын
Thanks man!
@davidv672
3 жыл бұрын
Great info. I am thankful for it. One item that could be improved is to tell your camera person to approximate the camera to the item instead of trying to zoom in from a distance. The Crab video was very interesting and informative, but the camera zoom did not allow for detail. Thank you for the info. Great work!
@justindearborn7275
3 жыл бұрын
Yeah the camera was a struggle I’m not savvy with tech at all so a friend did it and it didn’t come out good but at least the content was 😂
@williamt.heldjr.1046
3 жыл бұрын
Justin - Thanks for making this video. I just purchased a 1952 Dodge M 37. I have a few questions for you. Can you please email me. Thanks Bill
Thompson Family Homestead Haha I do this time a year it’ll go 60-65 all day long
@ecbravo999
4 жыл бұрын
Does it drive? How does it run?
@justindearborn7275
4 жыл бұрын
ecbravo999 It’s been running and driving perfectly for about seven years
@frankdavidson9675
4 жыл бұрын
thks for the reply on water problem here is the prob. all gaskets have been replaced no way for water to be leaking into tank the cap has a new gasket i got this truck dec 2011 iv had this problem all along i have removed the inspected it nothing found to tell how its getting in there. i set a boat tank in the back of the bed put the same gas in no problem i switched gas stations still water
@frankdavidson9675
4 жыл бұрын
i have a problem with my 53 m37 excessive water in gas tank i need help .??????????
@justindearborn7275
4 жыл бұрын
Frank Davidson Providing the gas cap is sealed up it’s probably the cork gasket on the top of the gas tank with a pick up and sending unit is it has that cover in the bed to access it it is not watertight and if that gasket is blown out water will sit on the fuel tank and run right in it you should have a drain on the back center of the tank put the front end up on some rampsLet it sit overnight then drain some off into a glass jar and you can see the water separated
@jorgegonzalez-pv8mv
4 жыл бұрын
Excellent work. I would like to know final speed and if you changed the brakes.
@justindearborn7275
4 жыл бұрын
jorge gonzalez The fastest I’ve ever been in it is 72mph, But it’s not recommended it’ll cruise 60-64 all day long, I never put disc brakes in it because the factory drums work great never had a problem never desired to replace them
@juanasanelli6831
4 жыл бұрын
Yo puse un 251a un M37 Es una adaptacion bien facil y es una maravilla como se comporta el vehiculo con el 251 !, anda mejor y es hasta mas economico de gasolina. El dueño actual,Es una amigo mio de años , lo quiso como de fabrica y de nuevo volvio el Dodge original ,pero Ay ! no anda como con el 251...
@justindearborn7275
4 жыл бұрын
juan asanelli ummmmm what? 😂 I can read the numbers
@juanasanelli6831
4 жыл бұрын
@@justindearborn7275 I instaled a 251 chrysler in a M37. Is a very easy adptation This M37 actualy is property a friend mine .. But he want the M 37 whith original engine The little Dodge But no run as the 251
@justindearborn7275
4 жыл бұрын
juan asanelli The 251 is a much better engine in every way, the stock dodge 230 is a turd 💩, if he drove the 230 he may change his mind there pretty slow
@juanasanelli6831
4 жыл бұрын
@@justindearborn7275 YES SIR ! A great pitty The 251 was a Industrial engine for a welder Hobarth that never in use The dodge m37 idling in 3a ... Pretty!
@alexanderraymond8238
4 жыл бұрын
Nice! Looks awesome
@user-nc4cx4gw2z
Жыл бұрын
Yeah it does! ✨
@explorer8888
4 жыл бұрын
Great info! Just a little blurry. Thank for taking the time to make it and upload it. Do you have a link to your friend from SLC channel? Can’t find it.
@justindearborn7275
4 жыл бұрын
Ony Quiñones (itchy old fart)is screen name or whatever
@explorer8888
4 жыл бұрын
Justin Dearborn Ok. Yes, I am familiar with his channel and his truck modifications. Awesome truck. And yours is very cool too. About a month ago I bought a 1963 M37B1 and I am in the early stages of the learning process. Thanks!
@justindearborn7275
4 жыл бұрын
Ony Quiñones that’s awesome there super cool trucks Reasonably cheap to build too
@alansmlth7989
4 жыл бұрын
Own a legend--Find a UNIMOG
@justindearborn7275
4 жыл бұрын
alan smlth If I wanted to Unimog I would have one
@alansmlth7989
4 жыл бұрын
@@justindearborn7275 Just find one, these M37s are everywhere but find a Unimog.or better yet a Sherp
@JohnMcNerney
5 жыл бұрын
Did you do anything to the brakes? I've been debating switching to disc brakes in the front.
@justindearborn7275
5 жыл бұрын
John McNerney I never desired more brake power the all new well adjusted stock ones have never been a problem
@JohnMcNerney
5 жыл бұрын
@@justindearborn7275 Thanks for the response. I was wondering if the higher speeds pushed the limits of the stock brakes.
@jrodjared
4 жыл бұрын
Are you still on the single master cylinder?
@datnotme9921
5 жыл бұрын
Wow, great review! I was a mechanic in U.S.Army '90's-'00's and didn't know these existed. 😲 About six months ago this truck came up on KZitem. Absolutely love the damn thing. Thanks for sharing!
@datnotme9921
5 жыл бұрын
My truck! I love this truck. I'll be looking for one soon. 👍👀
@dcummings7253
5 жыл бұрын
Re shoot this with focused zoom ins.
@slightlyalteredconcepts5561
5 жыл бұрын
I just bought an m37. So I'm going to rely on your info pretty heavy. Nice work on your old girl, appreciate the video
@justindearborn7275
5 жыл бұрын
Slightly Altered Concepts thanks man let me know if you need any info happy to help
@slightlyalteredconcepts5561
5 жыл бұрын
@@justindearborn7275 I greatly appreciate that
@timothykeith1367
5 жыл бұрын
George Asche in Venus PA is a wonderful resource for the flathead motors.
@LeonRFpoa
5 жыл бұрын
wow dude you got all serious about it. Good stuff. My film company just bought two power wagons as our fleet vehicles, now the boss wants one of these. They have been the most fun trucks you could ever imagine, especially the carryall. We have a stock 47 survivor, a restored 49 and a restomod carryall with a hemi and m46 tranny on the same driveline.
@justindearborn7275
5 жыл бұрын
LeonRFpoa haha thanks man, it’s nice to have one of these old trucks and actually be Able to use it
@sir_bertimus1547
5 жыл бұрын
Any chance I can see how you mounted the front engine mounts? I am trying to put a CDN military 251 with original transmission into a stock M37. I like the radiator solution with the electric fan. I was worried about how to move the radiator like the Canadians did. Many more questions if possilbe.
@AaronMartinCOOLVIDEO
5 жыл бұрын
Nice 1984 ATC 250R you should make a video about that.😉👍
@michaelcalnan5939
5 жыл бұрын
FFS sort out the focus on your camera! Its so distracting I stopped focussing on your dialogue. Great info, crap camera work.
@justindearborn461
5 жыл бұрын
I didn't ask for opinions and no one's holding a gun to your head to watch it
@350toocute
6 жыл бұрын
My father used to have a dodge power wagon just like this one.He never once had problems with the rear end or front end.It had the flat head six with a 4 speed standard transmission.
@ls26059
6 жыл бұрын
What a dumbass idea about the "blue rope" thing!
@justindearborn461
6 жыл бұрын
Jonathan Hughes why don't you do everybody a favor and shut the fuck up
@MrJeep75
6 жыл бұрын
I think the stock driver's seat is very comfortable
@MrJeep75
6 жыл бұрын
There's nothing wrong with the governor on stock carb
Пікірлер