Sori Bud, I`m a bit late on this video, but thank you very much for this tip..`I'm sure to save this video... My question is this this - when you unscrew them, is this the point where they normally breaks.. Or have you or maybe anyone else found that they break off anywhere else. ??
@vjdzonny
8 ай бұрын
Thanks for the video. I used this information to solve the same problem. But I managed it much easier and without a magnet, because I just didn't have a magnet on Sunday, I had planned to buy it the next day. My simple method was to inject compressed air into the glow plug bore and the glow plug's heating element flew out the nozzle bore.
@jumeirahkirk
8 ай бұрын
Cannot remove this head rest what’s the smalll u turn part you mention?
@marttigh3663
9 ай бұрын
good video
@GP-007
9 ай бұрын
My care same engine consume oil 4 L to 10000km
@matteofilighera1310
10 ай бұрын
It s valid for 1.4 tdci (dv4 ) engine??
@cookssohal2378
Жыл бұрын
their si a clip on the left hand side of the head rest wich needs removing
@montecarlo6569
Жыл бұрын
In Croatia 560€ for two handle. Insaine.
@Zeus2299
Жыл бұрын
Very Good. Thank you.
@crezzlin
Жыл бұрын
Hi.. My broken off tips don't seem to be magnetic.. Citreon c4 Thanks
@hfraat25
Жыл бұрын
Success I did mine ok.
@ivarlangseth2387
Жыл бұрын
Great instruction! What a clever mechanic you are :)
@kai9472
Жыл бұрын
Top notch, thanks
@kevinwarnes731
2 жыл бұрын
Looked at your video and thought I’ll give this a try ( Citroen Dispatch 1.6hdi ) I found that only the tip of the glow plug is magnetic enough to be picked up. Before you try this make sure the tips of the glow plugs are magnetic by testing a removed one. Tried and tried to get a connection just about to give up then bingo it worked. Thanks a lot for this tip. Hope I never have to use it again.😄
@markuswynne82
2 жыл бұрын
I just rescued 3 glow plug tips using this method. Sealed make a 5mm dia magnet which helped me. Not easy but it is doable
@alfatube100
2 жыл бұрын
Thanks very much. It happens the same with me, on one othe the glow plugs. I use your technique, and it worked. I little hard , but it works. Thanks, and keep up with your great tips.
@fagertun
2 жыл бұрын
Thank you so much for this. Worked perfectly! 🙌
@alexanderfoley3585
2 жыл бұрын
Hi, thanks for the video. I have just bought a replacement handle and not the whole unit. Could you advise how to just replace the handle? Many thanks.
@volleyballly
2 жыл бұрын
Hi, did ur handle just break as well? I have recently just bought the handle itself too. Looking for guide to replace just the handle. U managed to replace urs?
@selfloveandcoffee2914
2 жыл бұрын
@@volleyballly hii where you able?
@amjida8594
2 жыл бұрын
Hi mate were the best place too just buy the handle as myn broke off
@alexanderfoley3585
2 жыл бұрын
@@amjida8594 I think I got mine from Ali express online, but i've seen quite a few that have been for sale on various websites.
@pantheralaluna1111
2 жыл бұрын
Help !!! C250 coupe front passenger seat will now not return to normal seating
@markh3478
2 жыл бұрын
Helpful video thank you merci . My 2014 C250 is same design. Handle cracked underneath , dealer wants US$270 for part . Looks like a job for JB weld . The leather/vinyl around the handle trim is fragile so old credit card under trim removal tools for protection while prying.
@SuperPinhead123
2 жыл бұрын
I have the same car and my handle broke today. Glad I found this vid
@hfraat25
2 жыл бұрын
thank you I have this exact problem . I wondered if this was possible. the next problem is I have not yet got the injector free. thanks for confirming this is possible.
@diogovieira544
2 жыл бұрын
Thank you so much you save me a headgasket and lot of hours
@liamisic911
2 жыл бұрын
rip off prices to get this replaced my merc dealer quoted me £500 for this repair....
@liamisic911
2 жыл бұрын
@@TheMechanicsCar-ek1vm doing it right now mate 👍🏼
@liamisic911
2 жыл бұрын
Coukd not get the head rest off seems to be a locking catch when trying to pull it out.
@ramonewalkes9257
2 жыл бұрын
The head rest won’t come out? I see in the comment somebody mentions a u turn bolt . Where is that please ?
@georgegee7989
2 жыл бұрын
Same problem for me - I can’t get the head ready off. Any suggestions?
@buddyvangend
2 жыл бұрын
Thanks for the video mine has an airbag in that spot how do I disconnect or disable it as for it not to go off
@senadkasumovic488
2 жыл бұрын
Hello mean. Do you tried with endoscopic camera with magnet
@bogdanradulescu870
2 жыл бұрын
Hello. I am asking for a BMW 318d from 2017. When you do the oil change "at home" does the oil sensor feels that you have emptied the oil? It will pop out on the coputer when scanned? Or it is not sensed by the cars sensors? Thnk's
@boghybb
10 ай бұрын
If you don't turn the ignition on/ you won't start it, obviously the sensor will not detect anything.
@Mr11090
2 жыл бұрын
I put a long screw down through the tip of the glow plug and pulled up with a hammer.
@bobbychurch9820
Жыл бұрын
What screw did you use mate? Need your help!!
@paulsp2693
2 жыл бұрын
hi what's the code for the Bosch oil filter?
@paulsp2693
2 жыл бұрын
@@TheMechanicsCar-ek1vm thank you
@mikemedeiros7117
2 жыл бұрын
The mask? 😂😅
@tomasjankauskas4761
2 жыл бұрын
OMG Thank You very much!!!
@jonnathonsmith4450
2 жыл бұрын
What screw driver do you use for the screws in the back? Torx???
@MarceliGawrys
2 жыл бұрын
my mechanic told me that this is normal with diesel. with gasoline oil is very clean, but diesel is making oil black even in 5 minutes as you see. try to do this cool test with gasoline car ;)
@Jonodrew1286
2 жыл бұрын
I have done it on a VW Crafter because it was ceramic and I had no choice - I would say I drill and pull them out - I have done loads of them - again as a last resort I would push them in - but it would be easy to nearl the hollow end and get it stuck if you were in experienced - I would at the very least have a guide …
@a3211z
2 жыл бұрын
What engine oil you use for B47 engine can you please write me exactly
@paulsp2693
2 жыл бұрын
0w40 or 5w40 5 litre
@a3211z
2 жыл бұрын
@@paulsp2693 thats for sure totally worng its B47
@paulsp2693
2 жыл бұрын
@@a3211z it’s 100% correct, that’s what I use on my bmw 520d 2015 B47 engine…do you use something else for your bmw?
@meda5357
Жыл бұрын
@@paulsp2693 What oil do you use? I have a b47 190hp I use Castrol 5w40 I change it after 7-8000 km. Is it correct ?
@paulsp2693
Жыл бұрын
@@meda5357 I stay in Engalnd cold weather,and i dont have patience to let the car warm up,so i start the car and leave the house under 15sec,I use 0w40 castrol edge,I change at 10,000 km
@JGMLAD
2 жыл бұрын
Hi! Where can i buy one? Mine is broken! Thanks
@untitleditem2334
2 жыл бұрын
You're exactly the youtube guy I need. Especially since that weirdo from belgium produces crappy content on his 1 series. You're thorough enough to do a bang up job. Please don't get shy and upload. People would love more content on the 1 series, even maintainance would be just fine.
@untitleditem2334
2 жыл бұрын
I look forward to more videos, especially as I'm planning to buy a 1 series lci/ or a 3 series lci. Not sure if it's gonna be a diesel though. What oil are you using/ recommend for the b series engines ?
@christopherromero5325
2 жыл бұрын
What movie is that clip from? 😂
@mr718trapstar3
2 жыл бұрын
Where is the bleeder valve at on the motor to let air out of the cooling system
@tomcope5431
2 жыл бұрын
been hitting the tip but doesn't seem to move at all. I have already gotten the injector out, got an endoscope and magnet ready but that's as far as I've got. any suggestions? do you have to hit it really hard? the glows plugs are in the back of the engine so hard to get to!
@stefangiurgila7807
10 ай бұрын
Hi, not sure of you remember but did you still bang it out?
@jeanpierreragequit1726
2 жыл бұрын
Dont forget to insert and close ur new oil filter BEFORE ur carter bolt. In that way, u push & eliminate about 25cl of ur old oil. That could explain y ur next oil changes are still polluted.
@tsetsooooo
2 жыл бұрын
It turns out that only the wire is magnetic , the black cover cannot be pulled by a magnet if the is no wire inside it.
@CHIBA280CRV
2 жыл бұрын
Fantastic
@samhayes4085
3 жыл бұрын
You my friend are a legend 🙌
@smikelionis
3 жыл бұрын
👍👍👍
@antonypereira3853
3 жыл бұрын
Brilliant ,brilliant!
@asadalitruth
3 жыл бұрын
Mate your a legend I tried for hours couldn't budge it used the 15 torx few hits and it's out in the cylinder which I'll get out I really appreciate this video life saver
Пікірлер