Thanks so much for this video. Your explanation is great. I will attempt to unlock my door😵💫
@andremaia1117
2 ай бұрын
How does the ECU determine the direction of rotation?
@billebrill8730
2 ай бұрын
@@andremaia1117 I don’t think it needs to. It compares the pulses and if they are not the same then it knows there is a comparative error or if the wheels have locked up it can adjust the ABS. My car also knows which gear it is in.
@tonyrobinson2471
2 ай бұрын
Hi Bill, Thx for this. This is the same as a 2004 2 door Seat Ibiza, the only difference being that it is practically impossible to access the torx screw so had to resort to hammer and chisel. Without this video and your clear explanation I would not have known where to place the chisel. Door is now open just need to work out the easiest way to replace the door lock.
@steezin_4no_reazon
2 ай бұрын
Do the splines on the cv shaft to hub not just slide in and out like a normal cv shaft? Or was it just rust binding it up
@billebrill8730
2 ай бұрын
I was afraid to hammer it out after some gentle taps failed because of damage to the hub nut threads it also required some force to pull it home enough to put on the hub nut. There was only a little rust. Putting it in is also hard as there is nowhere positive to hit it because of the rubber joint.
@steezin_4no_reazon
2 ай бұрын
@billebrill8730 thanks for the tips, do a fair share of work on pickup trucks but never a bmw, sistsers is acting up so imma check this
@David-uu8vz
4 ай бұрын
One of best videos great detail
@billebrill8730
4 ай бұрын
Thank you
@eoin730
5 ай бұрын
How easy was it to do it with the bearing puller??? I might invest because I have to do this job in the coming days 👍🏻
@billebrill8730
5 ай бұрын
I needed both pullers but they worked well. Check you can remove the hub nut as that can be a show stopper, and invest in a BMW part when putting back .Depending on which side you do the exhaust hanger has to be unhooked.
@eoin730
5 ай бұрын
@@billebrill8730 wow I hadn’t factored in removing the nut, i looked at it this evening and sprayed it with wd40 in preparation, I have a brand new nut and reluctor ring for it, I’ll grab those extra tools tmoro and it should be ok then
@Spirittism
5 ай бұрын
my rear door is electric, any assistance?
@billebrill8730
5 ай бұрын
The lock is electric?
@Spirittism
5 ай бұрын
@@billebrill8730 the windows are automatic
@jumperxd3465
5 ай бұрын
Amazing video! You have really understood what people want from a tutorial and delivered excellently! Thank you Bill!
@SfisoMosinki
5 ай бұрын
It's a electronic window
@YoungTruckerUK
6 ай бұрын
Where did you get that puller tool that you used to install the shaft? Have looked around for something like it but to no avail. Thanks!
@billebrill8730
6 ай бұрын
Use this search on eBay '7pc Drive Shaft Puller Service Socket Set**M16 - M30**Vag**VW**BMW**Merc**'
@TacticalFriedChicken
6 ай бұрын
Great video and i love how you actually showed what tools and steps there are. Love chrisfix but i feel he's shaking over this
@kennethallison4436
7 ай бұрын
sound too low
@billebrill8730
7 ай бұрын
First time anyone said that!
@adamcaleb
8 ай бұрын
one of the best tutorials I've ever seen on KZitem. really clear, no bs and good pace. 10/10
@billebrill8730
8 ай бұрын
Thank you
@OscarPikeCountyPA
8 ай бұрын
Brush the splines with grease using an old toothbrush next time. It will make future removals a breeze.
@lothar153
9 ай бұрын
Step 1: remove abs sensor, Step2: insert a new abs sensor with an thin spacer (max 0,7mm) Done Works for 12000km now Of corse is your solution the better one… but if the car is very old and only 2k worth… my solution is the better one 😝
@billebrill8730
9 ай бұрын
Agreed, if you watched my other video I showed how to do that. I used it as a temporary fix but did not need to replace the sensor.
@richardelliott8747
10 ай бұрын
Hi.. I just wanted to thank for such excellent instrutions/ directions which were a great help in not giving up the quest .. job done !!
@KatarzynaArchacka
10 ай бұрын
@bill ebrill when the light flickers, does the car also break shortly?
@KatarzynaArchacka
10 ай бұрын
@bill ebrill when the light flickers, does the car also break shortly?
@arminm6527
11 ай бұрын
thank you
@gt4boys
11 ай бұрын
But why do you remove the driveshaft? Why not just do it while it’s on the car? Any good reasoning? Other than it being more «available”?
@billebrill8730
11 ай бұрын
Apart from not being able to access the ring, a new ring cannot be fitted with the wheel bearing and wheel mounting in the way. Removing those is a far bigger job than taking out the half shaft which is relatively easy.
@lukiluki2366
Жыл бұрын
Thanks for the video. What sensor do you recommend or what have you used? How do they behave? Thank you.
@billebrill8730
Жыл бұрын
My sensor had been marked by the expanding reluctor ring but still worked fine so I did not replace it. The BMW part number for my 2009 318d sensor is 34526762466. It operates as a single channel sensor with current output of 7ma and 14ma for measuring rotational speed. See my other video.
@robotb57
Жыл бұрын
Where did you get the universal puller set I can’t find one on eBay
@billebrill8730
Жыл бұрын
I can see about five on eBay UK using using this search "7pc Drive Shaft Puller Service Socket Set**M16 - M30**Vag**VW**BMW**Merc**"
@andymalakov4283
Жыл бұрын
Very helpful video. Thank you! Would be great to know which exact Universal Puller Set was used (so many different ones on amazon)
@andymalakov4283
Жыл бұрын
ahh.. seems like "CV Axle Shaft Puller / Wheel Bearing Hub Installer Kit - Bavarian Autosport" was used.
@billebrill8730
Жыл бұрын
Thank you. I bought on eBay - "7pc Drive Shaft Puller Service Socket Set**M16 - M30**Vag**VW**BMW**Merc**" a few places do them. The place I bought it from are out of stock I see others doing it.
@skotsephrenia1
6 ай бұрын
Hi there... Is there any place in Dublin where I can get this puller.. I was replacing my E90's reluctor ring using a sledge hammer and I damaged the spline of the shaft
@thomaswalsh6313
Жыл бұрын
Very helpful, well detailed and clear. Thanks 🙂
@aacar4095
Жыл бұрын
Should you grease the drive shaft splines before reinstalling? We had one completely rusted and frozen in the hub.
@darkotepic2941
Жыл бұрын
Thanks man,you helped me a lot!
@suilfisean
Жыл бұрын
Excellent tutorial Bill, succinct and only useful information 👍
@taulebelo9728
Жыл бұрын
Thank you so much for your help
@jurgenalderan3032
Жыл бұрын
Thanks allot for this super vid .Helps me verry to understand the Problem 👍👍👍😀
@LaunchGoodhue-xj6lv
Жыл бұрын
Very helpful video Thank you. The cut outs to show the dead lock were great 😃👍
@thomaslynas721
Жыл бұрын
Just the job. Thanks One thing not covered is the removal of the window dowels which i believe can be very very difficult.
@billebrill8730
Жыл бұрын
Thanks
@thomaslynas721
Жыл бұрын
@@billebrill8730 Can I disable the deadlock lever and use the door till I get the correct lock. Would it get through an MOT
@TheBlaert
5 ай бұрын
@@thomaslynas721 as long as the door opens and closes it should pass the MOT
@MsRustynuts
Жыл бұрын
Great video thanks.
@dzidmail
Жыл бұрын
The newer ones always show 7mA .
@billebrill8730
Жыл бұрын
They must use a different protocol.
@dzidmail
Жыл бұрын
@@billebrill8730 Yeah, it's probably this one, kzitem.info/news/bejne/mqiG0IBviXd8ZZw although I was not able to see the square wave. Maybe. I would have to do it installed on the wheel. Cheers.
@billebrill8730
Жыл бұрын
@@dzidmail That was how I started unfortunately it is uses a current sensor arrangement. It is not a voltage protocol, it is a current protocol, switching current levels and difficult to detect with a scope.
@dzidmail
Жыл бұрын
@@billebrill8730 Actually yeah. This is must be the same protocol. Although, with the 200ohm resistor in series the voltage drop changes (1.4V) should be visible on the scope. I think, either my new sensor are bad too or I need different metal to test them on.
@dzidmail
Жыл бұрын
Let me report my memories - maybe will be useful to someone. Your sensor is showing 14mA on far proximity and 7mA on close. My failed rear sensor one was showing 7mA on far and close proximity. Replacement rear sensor was behaving like yours 14mA on far proximity. Now, week later front sensor started reporting error. Yeah, suspicious. It was reading 7mA on far and close proximity. Bought the replacement and was showing correctly 14mA on far proximity and 7mA on close, they sent wrong size (thick rear kind). Then I ordered two Chinese front sensors from different manufacturers. I thought I will stock up on them if another one fails. Both were showing 7mA on far proximity, so they are probably failed as well. They costed $8 and $10 and they are probably some manufacturing rejects. I am going to buy another one and maybe will report further.
@honestman0009
Жыл бұрын
God bless you man 🙂 I opened the door this way, removed the lockdoor, installed a new one, locked it and the same situation again, I can't open it either from the inside or from the outside. What's the problem
@billebrill8730
Жыл бұрын
Sounds like a wiring issue!
@honestman0009
Жыл бұрын
@@billebrill8730 I also think that electricity is a problem
@tom83735
Жыл бұрын
Dear Bill, Thank you so much for making this video. It helped me a lot!
@billebrill8730
Жыл бұрын
Glad it helped. B.
@PzkpfwV
Жыл бұрын
A lot of info condensed in a short video, hard to find nowadays. It's possible to open the lock without having to drill a hole. Use a slotted screwdriver and hammer it into the small latch seen above your thumb @3:40. This rotates the plate and unlocks the door.
@billebrill8730
Жыл бұрын
I agree. Well done. It is also possible to fabricate a driver to access it from the side. Coincidentally my daughter traded the Polo two days ago - we got 15 years out of it across two daughters. It was a 2005 car!
@PzkpfwV
Жыл бұрын
@@billebrill8730 Nice, probably the last generation of cars you can really work on and fix things like this cheaply.
@AfnanKhanYousafzai
Жыл бұрын
I have followed this procedure and have not been able to open my door rear offside passenger door ..the screw plastic and metal part all out .. not sure if I can upload photos in comments any help will be appreciated.. vw 2005 polo 1.4 auto
@ainerush8942
Жыл бұрын
Are you anywhere near armagh
@billebrill8730
Жыл бұрын
No, Dublin.
@ainerush8942
Жыл бұрын
@@billebrill8730absolutely tortured with trying to get someone to sort this exact problem for me.
@Wasper216
Жыл бұрын
Painting the shaft wouldn’t have made much of a difference. When you hammer the new ring on, the paint will scratch anyway. Thanks for the video and info about the tools needed. 👍
@dzidmail
Жыл бұрын
No kzitem.info/news/bejne/03iiunyBa2upa5g
@atommi1
Жыл бұрын
Where did you buy those special tools for bolts? Thank you.
@billebrill8730
Жыл бұрын
I bought puller here - www.ebay.ie/itm/282105048992?hash=item41aec56fa0:g:wCoAAMXQL99Sczue&amdata=enc%3AAQAHAAAA4K1pQqN8dV8hoMSDHC0%2B5%2BF%2Fkr5wpMJe9VnmSg8BodrQN7aZ6hJjjO%2B8Z0diyFRxXIGe3SrRnDdyRGElAnkSbvTWFc7lWYsSjAXM5IpL4S1UVokczoLFPoyX5qrJI6MqUx58mRXg9vX620GVaV54CWYEW45l7jKbx%2FbdZCm7BBDO1X7PuSiCvxxDHDOPnk0VRZVXZVh3tbnzgGnjwO98IYQF%2Bvh16fXuDnXD0ZlE2IO9wTGG7jvMrgAzisap2k2MrsE%2B%2BHdfXaXiXr6WxGqkG2IPmz710ZpEpWUjixEx8sPM%7Ctkp%3ABk9SR86F_-PPYQ
@jackduckworth1100
Жыл бұрын
Job done after months of frustration. You’re a star!
@kiwiexotics1982
Жыл бұрын
is this one side or both rear wheels? Thanks Im about to embark I was wondering if they had rings on both sides so I need to buy one or two?
@billebrill8730
Жыл бұрын
This is one side. Both sides have them. It is how they tell if one wheel is slipping. I had the other side done by a dealer and it cost me €1,200 because they replaced the full half shaft. That is why I did the second one myself.
@phillewis7910
Жыл бұрын
Awesome guide. Thankyou
@rickyl9939
Жыл бұрын
Thank for your sharing Bill. It truly helps me doing it.
@billebrill8730
Жыл бұрын
Thanks, nice to get the feedback.
@aidsy60
Жыл бұрын
Great tutorial, thanks a million 👊
@mystery3882
2 жыл бұрын
Just tried it and worked only the door skin was a hassle thanx very much.
@billebrill8730
2 жыл бұрын
Appreciate the comment. Getting the door card off was a bummer. However easy to put back once open!
@rollydoucet8909
2 жыл бұрын
I have a 2005 320i (E46) with the 2.2 litre six cylinder engine. I want to replace the ABS sensor rings, however any source that sell those rings lists the 323,328 and farther up the model line. I'd like to know if the rings listed for the 323 etc will also fit the E46 model 320i.
@MrAfrikaan
2 жыл бұрын
Absolute legend you are mate. After hours of trying and searching, this did it for me. Thanks heaps.
@yokivetha318
2 жыл бұрын
Hey Bill, would this fit a 2008 323I ?
@berrymallens3782
2 жыл бұрын
Thanks for the video, its the only information i could find about this issue, i drilled a hole, unscrew the Torx screw and the door opens again.
Пікірлер