Thank you for the video, I was cussin up a storm trying to figure out how the shaft came out, I would have never guessed there was a giant nut on the inside. Putting my new wheel bearings on now, and its back to work for this old tractor
@JPN76
9 ай бұрын
Glad my video could help!
@ronrydell1679
Жыл бұрын
Very well done. I like that you do this in real time. Not making it look like you can do a five hour job in 15 minutes. Thank you for your video.
@JPN76
Жыл бұрын
Thanks for the good feedback. It's definitely easier for others to follow along this way. Takes me three times as Long dealing with the camera and editing but well worth it I think.
@nedfoley
Жыл бұрын
This is fantastic!! Just discovered your project and am binge watching. Now a subscriber. Keep up the great work.
@JPN76
Жыл бұрын
Thank you!
@thomasbellamy4850
2 жыл бұрын
Another fantastic video thanks for sharing your progress in such detail.
@JPN76
2 жыл бұрын
Thank you sir!!
@flyfliker
2 жыл бұрын
I own a 1948 B. Your videos and dialog are fanrastic. Where do you purchase yoour parts?
@JPN76
2 жыл бұрын
@@flyfliker A lot come from Reliable Aftermarket Parts on ebay or Amazon but some from Stieners and the engine kit was from Yesterday's tractor. Seals and other odd and ends from Advanced auto parts.
@nagvajrala3824
2 жыл бұрын
missed this one. so will watch it twice 😁
@kveltman4672
Жыл бұрын
Nice job on the rebuild! Looks great! Did the pan need a gasket, or just the gasket maker you showed? Also, what gear lube did you put in it?
@JPN76
Жыл бұрын
Thanks, I just used gasket maker. I recommend the ultra grey, and it seems to have the best consistency.
@kveltman4672
Жыл бұрын
@@JPN76 what gear lube do you use?
@JPN76
Жыл бұрын
@@kveltman4672 80w-90. Anything close would work
@jockyi
Жыл бұрын
The grunts are just like a torque wrench click. Better to leave them in. Great work. What orange did you go with?
@JPN76
Жыл бұрын
I agree. That's why I left them! As for paint I used tisco persian orange #2 with hardener. smalink.com/default.aspx?page=item+detail&itemcode=TP285GAL&catlist=8514&parent=3748
@corykeller5076
3 ай бұрын
Do you have the bearing numbers for the 4 final drive bearings and also the seal number for the differential/transmission where the axle shaft goes into the differential? Great video!
@JPN76
3 ай бұрын
I do not have the bearing numbers, but the seal numbers are shown in my transmission assembly video. Thanks for the good words.
@seniorelectrician6831
2 жыл бұрын
First, thank you for you Videos! What kind of paint did you use to paint the inside? I know that there is many types and thickness of gasket material, Any way to determine what type and thickness to use such as with your shims and paper?
@JPN76
2 жыл бұрын
The paint on the inside is just oil based rustolium. It doesn't contact oil so no need of a special paint. You could figure gasket thickness in many ways I imagine. Easier to do with this by adding too many shims then back down one. In the automotive world I'm a bit more precise. Here i am going by feel. The manual in many places say tonjust get a nice rolling fit with no endplay. One trick I sometimes use is to put a thick piece of solder in between where the shim goes then tighten it down. Measure the solder and subtract the preload from the measurement or add to it if the spec is end play. That method may not work well with shims like this though but works good with shims behind races.
@JonoHaack
Ай бұрын
Hi, whereabouts do you source your new bearings and seals from? Thanks for your help
@JPN76
Ай бұрын
@JonoHaack the seals were autozone. But i did not need bearings. Between the two tractors, i had what i needed
@seniorelectrician6831
Жыл бұрын
Re-Watching, I just picked up a transmission/rear end for a B with finals as my final housings were grooved the outside and had mix matched bolt sizes, banged up pans, etc. On yours, Did you have to replace the bearings?
@JPN76
Жыл бұрын
Lucky for me between the two transmissions I ended up with enough good bearings.
@joemcdougall7605
Жыл бұрын
I just reassembled mine and notice some chater between the bull gear and final drive gear. It sounds noisey when i turn it by hand. Should it have so much play between the two gears?
@JPN76
Жыл бұрын
Mine doesn't make any noise. Only clicks a little with small amount of backlash when I rock it back and forth. Are the gears all original. I saw in the parts manual different years will have different gear ratios. Tooth count is slightly different. May a gear was replaced with the wrong one? I think I remember you had a C as a parts tractor? If you used the bull gear from that it might be the issue
@Midwesternrailroader
Жыл бұрын
I have several 1940s and 1950s allischalmers tractors. I have looked online for a parts catalog for bearing seals and gaskets and have not had any luck finding many items. Where did you find your parts?
@JPN76
Жыл бұрын
The seals I matched up by size entering the shaft and bore size on a temkin web site. Ordered cheap at auto zone. Bearings I ordered by the number on the bearing from parts stores. Gaskets and other stuff was stiener tractor. Yesterday's tractor and Amazon. Many gaskets I used RTV even if a gasket was available.
@Justin-ne2xo
10 ай бұрын
Both wheel bearings can be bought at Oreillys. Number is on the inner race of the bearing
@seniorelectrician6831
Жыл бұрын
did you sandblast this housing? Seems to me you said at least in other videos that you sandblasted the cast item you were working on. That must be I good sized cabinet if you can get housings in it
@JPN76
Жыл бұрын
I sandblasted the smaller stuff. I used a needle scaler and wire wheel on the larger parts. I sent you some pics of the block as an example on Facebook messager
@seniorelectrician6831
Жыл бұрын
@@JPN76 Got them, It took a while as stuff like that doesn't work on company wifi so I had to use data to get in.
@user-qm8ls2tj5y
Жыл бұрын
Is rtv the only seal you used on the bull gear pan?
@JPN76
Жыл бұрын
Yeah that's all I used. Not a drip at all. And any modern stamped steel pan uses rtv only so it shouldn't hurt anything.
@user-qm8ls2tj5y
Жыл бұрын
Thanks for the feedback!! Great video
@BobontheFarmOhio
2 жыл бұрын
You do a lot nicer looking work than I do! I know that misery loves company but aren't those little brake springs a royal pain? I sure think so!
@JPN76
2 жыл бұрын
Yes they are! I edited about 10 min out of that spring part. The level of work changes based on need and what the wanted final outcome is. Yours worked great for your plan to get it running as is. My tractor is a little more sentimental I grew up on it and now it's going to live inside and only come out for fun. This is the first tractor I have ever restored and I'm sure I'm going a bit overboard.
@JPN76
2 жыл бұрын
Also there is a big difference between repairing the tractor and restoring to like new. Don't cut yourself short.
Пікірлер: 39