Thanks for posting this video. My 89 S10 was the exact same set up. I too was trying to figure out how to get that 13mm nut off without moving the arms. Vise grips worked like a charm and I got that nut off.
@leerevier1003
3 жыл бұрын
I found this video today and was planning on replacing the motor. Great video tips on how to get the cowling off. Another good tip about replacing the washer nozzle..... I will order the hose and nozzle when I pick up the motor from autozone. Thank you so much for these videos Dan! Your video will help me keep this old truck on the road for another 30 years. This was last of the small mechanical issues to fix .... then I take it in to get a new paint job to restore it to its original condition.
@danjarrett
3 жыл бұрын
Sounds Great. Glad My Video Helped out. I love My old S10.. Thanks for watching.
@stevec5935
2 жыл бұрын
Thanks for posting this; I have an ‘85 S-10 and the wiper motor just up and died (how rude of it). Worked one day; didn’t the next. Troubleshot to the motor, and I couldn’t believe that O‘Reilly had one in stock! This video was very useful. Appreciate it.
@danjarrett
2 жыл бұрын
Glad My Video was able to Help You out. Good luck out there. Thanks for watching.
@user-fe5df6xj7r
5 ай бұрын
Thank you, have the same year Tahoe short box '91 pickup but blue. Wipers quit as I Left.. ? So doing this tomorrow- Friday.
@anthonyhopper3413
6 жыл бұрын
Thank you Dan. I am using this on my 1983 S10.
@danjarrett
6 жыл бұрын
Glad to be of Help. Thanks for Watching.
@HardCoreGarage
Жыл бұрын
Love them lil s10s!
@marcusjones7082
7 жыл бұрын
Awesome video! Thanks! I have an 87 s10 Blazer and everything looks about the same. Going to go get my new motor tomorrow and throw that baby in
@DawgYa1
2 жыл бұрын
Great video, came in handy to help me fix a coworker's wipers
@hectoroctaviosanchezcastel4345
4 жыл бұрын
Thank you very much it helped me a lot, I was removing the leaves from the trees that were underneath and I did not know how to remove it, a thousand thanks, greetings from Mexico.
@danjarrett
4 жыл бұрын
?
@hectoroctaviosanchezcastel4345
4 жыл бұрын
Thanks
@Tewrobert49
7 жыл бұрын
Its all good, Stick with the whole video..Done me a lot of good..Thank you sir
@FastandFoody
6 ай бұрын
Thanks for the videos they sure help out.
@theforgotten081
4 жыл бұрын
Thank you. Couldn't figure out the wiper arms for the life of me
@danjarrett
4 жыл бұрын
Thanks Glad I could be of Help. I couldn't figure that out either at first. And then after the Job I was Paranoid that They would Just fly off the next time I was in the Rain. But they didn't and have had no Problems with them since then. Thanks for Watching.
@stratsurvivor
3 жыл бұрын
Got to replace mine today. Tutorial was perfect. Thank you so much!
@danjarrett
3 жыл бұрын
Glad I could help. Thanks for watching.
@THE_SHEFF
5 ай бұрын
Appreciate the tips and everything. I'm about to do the same thing to mine. I found a nice 91 Tahoe edition s10. V6 5spd. 2 owner truck. Very little rust. An I was wondering if you had ever messed with the throttle body injection system? Mine seems to be sluggish every so often. Other than that an exhaust gasket I don't have to do much. I'll be replacing the passenger side window track in the door. Bought a complete door used, for parts. Truck has 212k miles on it.
@danjarrett
5 ай бұрын
No I never had any problems with the throttle body system.
@allenneese7459
7 жыл бұрын
Thanks for the video Mine went together fairly easy
@richardpersoage8504
5 жыл бұрын
I like to change the arms with claws for later wipers.
@domonichutchinson6912
4 жыл бұрын
Thank you very much! Helped me a lot!
@rclamb04
4 жыл бұрын
Thank you I have to do this tomorrow and I am no mechanic still kinda nervous but this should help a lot. Yahweh bless
@danjarrett
4 жыл бұрын
It is a Pretty simple Job. Just Step by step. Good Luck. Thanks for Watching.
@rclamb04
4 жыл бұрын
Dan Jarrett got it done had to overcome some obstacles but it’s fixed. The brackets that hold the things the arms are attached to are both broken so they wobble do you happen to know if one can get just those brackets or do you have to buy the whole wiper assembly? Thanks again
@danjarrett
4 жыл бұрын
@@rclamb04 I don't know. I'am sure You can find them at the Autozone or where ever.
@angelcage4040
5 жыл бұрын
Great video! Down to earth! Gotta do my 89 s10 blazer
@danjarrett
5 жыл бұрын
Yes it is a Pretty Easy Job. Thanks for Watching.
@mdogg1604
5 жыл бұрын
Same here...'89 S-10 Blazer!
@Yukizan
5 жыл бұрын
Thank you for the full tutorial, exactly what i was looking for :)
@danjarrett
5 жыл бұрын
Glad it was Helpful. thanks for watching.
@jimhamilton6209
5 жыл бұрын
Just watched your video and getting ready to do the replacement. Great video btw, hope mine is as easy as yours... 88 s10 4wd supercab. I'll log my response in reply. Thanks for the video.
@danjarrett
5 жыл бұрын
Hope Yours goes as good as Mine did. good luck. thanks for watching.
@jimhamilton6209
5 жыл бұрын
It did not go well at all. Put a 2nd board in and it immediately fried a resister. Turns out, I'm pretty sure the problem is in the switch as the low and high wipers are on at the same time sending too much voltage to the board. That switch is in the steering column, been there done that before tightening the universal joint so tomorrow more fun tearing down the column but not as far this time... hopefully. Thanks for the good tidings tho.
@danjarrett
5 жыл бұрын
@@jimhamilton6209 Sorry to Hear about all that. I too Have Had my share of Steering column Problems. It's a Tilt Column and Mine is Loose but seems impossible to get to the Bolts to tighten up. Also My Horn Shorted out and would drain the battery down over night. so I had to Pull the Fuse for that. I Hope I don't ever have any Problems with the remaining Electronics in the Column. I don't know If I even want to work on any of that. Best of Luck.
@TWiumph
7 жыл бұрын
Thank you very much. Solved my problem!
@danjarrett
7 жыл бұрын
Glad it Helped. Thanks For Watching
@dwuuwd6914
7 жыл бұрын
Thanks for makeing , very useful
@yulpinto5540
7 жыл бұрын
Thanks for the video
@HotRodDad
3 жыл бұрын
Very good tutorial.
@danjarrett
3 жыл бұрын
Thanks for Watching
@richardpersoage8504
5 жыл бұрын
Wow! Corvette rims on your S-10.
@danjarrett
5 жыл бұрын
Yes. I'am told they are 1982 Corvette Wheels. I think that was the last Year they Made Carborated engines for those. Thanks for Watching.
@shartne
7 жыл бұрын
Yah Hooo all fixed! =)
@nicholasnardone3154
7 ай бұрын
That’s why I’ve always had s10 maintenance is so cheap
@jonathanhankins790
3 ай бұрын
Im obviously late to the party here but i got a 89s10 tahoe, 4.3v6. Wipers just up and quit, on the windshield, still that way. No fuses blown, mother board looks good, to Mr. So solder issues (that was a option from things i was reading). But im guess the motor ? Just wondering what your experience was with yours.
@loggingtheozarks
3 ай бұрын
Just curious if yours is like mine today. Does the relay on the circuit board make noise when you try the wipers?
@jonathanhankins790
3 ай бұрын
@@loggingtheozarks you mean when it quit ? If so, i didnt pay attention to it. I dont think but ill look later.
@jonathanhankins790
3 ай бұрын
Sprry im late sir bit no it don't make a noise. I wanted to ask yiu what u did to get the linkage bolt loose ? I see u held it with something but i can figure out how to keep mine still to get loose ?
@loggingtheozarks
3 ай бұрын
@@jonathanhankins790 Mine was actually locked up so it was easy to get loose. But I would imagine you could put a small piece of wood under it. I think you may have a circuit board issue.
@jonathanhankins790
3 ай бұрын
@@loggingtheozarks i thougjt i seen in your videos that your linkage was moving when tring to get that bokt lose,so that's why i was asking. The circuit board is just as much as the whole motor for me so and its still the original one from 89 so i figured why not.
@anthonysantillo1358
7 жыл бұрын
THANK U
@danjarrett
7 жыл бұрын
Hope it was a Help. Thanks for Watching
@c.everett7131
5 жыл бұрын
The part # for this motor is (40-190)
@JBD0909
3 жыл бұрын
How long did this job take you? Heading out at around 5 am to fix mine to go to a party tonight, lol.
@mdogg1604
5 жыл бұрын
Great vid; thanks!
@danjarrett
5 жыл бұрын
Glad you liked it. Thanks for Watching
@williampowell1783
5 жыл бұрын
Next time you can replace motor without removing all that other stuff. Take 3 bolts out of motoer and it will fall out far enough for you to remove the stuborn nut. Also there is a fix to circuit board, iLL SHARE WITH YOU IF YOU NEED IT. OPPS HIT CAPS LOCK.
@VVeMoveForward
3 жыл бұрын
I'm interested
@latuyiadelsosa7852
2 жыл бұрын
hello friend regarding the change of the motor I also made the change of mine but I have a problem when putting the blades, they no longer stay when I put them in the normal position, they go down to the hood or come out of the windshield, I don't know how to make them stay in their position do you think you can help me?
@williammurray8060
Жыл бұрын
I think your arm nut may be loose.
@THE_SHEFF
5 ай бұрын
Be sure to mark the area where they were in factory settings. That way you can easily adjust if needed. 1 tooth on spline goes a long way
@outoftime788
4 жыл бұрын
the way u removed those wiper arms is not workin for me. its jus too hard im putin all my strength into it. im scared to break it
Пікірлер: 66