I had 2 different repair shops tell me the shift forks were worn and transmission needed to be rebuilt. After I said screw that, I played with the shifter lever and figured out that it shifted fine if I just lifted it a bit from the transmission. Then I pulled it out and learned the rubber bushing was completely disintegrated. Replaced that 15 years ago with a oem, and did it again yesterday with an Ebay aftermarket different material because it was completely disintegrated again. I hate how these shops lie to people about a $20 fix.
@manuelgonzalez8146
3 жыл бұрын
thanks, it sure help me a lot, i did not have an idea what to do to fix my toyota 1991.
@samsen3965
Жыл бұрын
Good to mention NAPA. Never knew they have the part for cheaper.
@LL-cz5ql
5 жыл бұрын
Great video, this will really help me out when I try it in a couple days.
@lomuitet
5 жыл бұрын
will fix my car exactly what you hadThanks for letting me know I
@tubejim101
5 жыл бұрын
Your welcome
@pianist8744
6 жыл бұрын
I need to do the timing chain as well. There is not much detailed content on the web about this. I look forward to watching if decide to post. Regards, Adam
@anderswakatsuki
3 жыл бұрын
Very helpful video! Heads up the NAPA part number for the shift bushing kit is #600-2464 if that can help anyone out.
@kuyukgwangwang1817
4 жыл бұрын
This video is helpful 😎
@adamjones3936
2 жыл бұрын
What size are those 4 screws that hold the mounting together? Mine are missing and I cannot figure out what size it is
@tubejim101
2 жыл бұрын
I would call Toyota Dealer, and see if they know. If not, ask them for the part number, and research from there. You could also go to a wrecking yard and pull them. Maybe buy some from a wrecked pickup on facebook. They should be metric, so you could just try some metric screws.
@pianist8744
6 жыл бұрын
Ok, now show me how to replace the headgasket! My 22re has been sitting for a year.
@tubejim101
6 жыл бұрын
Hopefully soon. Want to change the timing chain, so most likely will do the head gasket at the same time.
@jasonnieto1242
Жыл бұрын
Hey I know this is an old video but I have an identical 91 pick up and it recently got stuck in reverse like it won’t go into any other gear, I tried the “removing reverse light sensor and pushing pin readwards” I’m gonna take a look at the bushing when I get home but if this doesn’t fix it any ideas?
@tubejim101
Жыл бұрын
While pushing the stick out of revers, have someone gently rock the truck front, and back.
@johnjames77
Жыл бұрын
The shifter knob is so hard to remove that I have never taken it off.
@gregmize01
11 ай бұрын
MY BUSHING WAS COMPLETEY DISINTEGRATED!
@philippelescarbeau7082
3 жыл бұрын
causes cancer in california 😂
@elizabethfletcher1487
3 жыл бұрын
All products sold in California must prove they do not cause cancer in order to get the right to have that silly-sounding warning removed from their product. The warning means the supplier has either chosen to not secure proof, for whatever reason (like maybe it does cause cancer, or maybe it is just not cost effective to prove a hunk of metal or plastic does not cause cancer).
@vegaf2011
3 жыл бұрын
Is the 1990 model the same method?
@tubejim101
3 жыл бұрын
Think 85 to 95 DLX models should be the same.
@vegaf2011
3 жыл бұрын
@@tubejim101 thank you 🙌 I did everything but I was unable to remove my shift knob I tried twisting it counterclockwise and nothing. Like if it was welded in 😅. Any clue how I can go about that? I want to get a new shift knob
@jonascagape520
4 жыл бұрын
Is it okay to remove gear boot when driving?
@Henny_Daddy
3 жыл бұрын
Yeah, it’s just a cover so you don’t see all that nasty stuff under the boot🤣
@jonascagape520
3 жыл бұрын
@@Henny_Daddy i dont remove it because i get confused what gear am i in hahaha
@elizabethfletcher1487
3 жыл бұрын
As long as you don’t mind vermin, dirt, wind and water entering your cab, the upper boot is not necessary. The lower boot is required to keep all those things out of your transmission box.
Пікірлер: 28