Thanks for posting this video! Good job explaining the steps.
@stephenwest5469
3 жыл бұрын
Thanks for this video man, it helped tremendously.
@deancolonel5246
6 жыл бұрын
Used video for 2011 Sorento lx. Super helpful, pretty much step by step. Thanks a ton for making video. Successful install!!!
@deancolonel5246
6 жыл бұрын
Scott L, luckily didn’t have to use one, but it did rent it just Incase. The hardest part was separating the control arm.
@jeremiahellis4536
5 жыл бұрын
Thanks Sean Cavanaugh. I wonder if this was related to 2011 Sorento. This will help me alot.
@261ziggy
4 жыл бұрын
Thanks for the video however the cause of your recurring problem might be the worn carrier bearing of the intermediate shaft and therefore the wobble.
@embededfabrication4482
Жыл бұрын
100 car repair karma points for making this video I had to go at my axle nuts with an angle grinder to get it loose you can do it whout taking the brakes off, just be careful to not pull on the lines also, I just disconnect at the strut and tie rod and leave the ball joint, it pulls back and you can get the axle out no prob
@jimmymolinaro7554
2 жыл бұрын
3 chains, a come-along, your backyard deck post, a shade tree backyard mechanic video if i ever saw one. "And the Oscar goes to,,,,,," LOL
@ep2653
4 жыл бұрын
When you tighten down the lower ball joint, does the weight of the vehicle have to be on that component?
@stam9241
7 жыл бұрын
My mechanic took the shocks off to get the axles out of my family's 08 Sedona, he didn't separate the ball joints or calipers, however. Both CV axles came out relatively easy. The Rockauto axles (Trakmotive) has vibrations at 30mph. Really disappointed. I'm saving the old axles for a rebuild eventually.
@javierochoa432
5 жыл бұрын
When I was changing my struts my cx axle popped out on its own...I didn't have any more money to buy it but I'm worried about it smh
@rahrah8076
5 жыл бұрын
Javier Ochoa just remove the axle nut and hit the end of cv axle and it will pop back in
@jeremiahellis4536
5 жыл бұрын
Thanks for video Scott L
@CarsandEspresso
2 жыл бұрын
Good job! I have the same style of video making... on my 2008 Kia Sedona - do you have the torque specifications?
@mikey27437
8 ай бұрын
My 2011 Sedona had both drive shafts replaced in a garage. New shafts were aftermarket as Kia dealer wanted 1000Cad a piece +tax . I found that aftermarket parts were vibrating during rapid acceleration. Changed them a couple times new ones were still vibrating. Mechanic told me he was not able to find the cause. The only thing that was changed were both drive shafts. Is it your experience as well? Did you notice if aftermarket drive shafts caused vibration during acceleration compared to original parts? Thank you.
@nickyalousakis3851
8 ай бұрын
really old video now. but if you remember.... were the replacement cv axle was it factory or was it from amazon? i might have to change mine and don't want to do it twice. best.
@Sroor2023
5 жыл бұрын
😂😂😂 We didnt see you in action fighting with that axle trying to remove it 🤪🤪🤪 We need the full session 🤨🤣🤣🤣 a chain and hook 🧐🧐🧐 God help you with this nightmare
@jarist1
5 жыл бұрын
Hello. Lari here. Got a 2012 Sedona. Are you using a driver side shaft and installing at that spline separation?
@jarist1
5 жыл бұрын
or do you perhaps have a parts # for what you installed?
@dwightlee6164
2 жыл бұрын
genius! thanks
@drjrdonaldson8415
Жыл бұрын
Thanks!
@peterh2800
3 жыл бұрын
Thankfully. *****👍👍👍👍👍
@RubenGonzalez-wj9me
5 жыл бұрын
Scott L, Good job
@timidater4803
4 жыл бұрын
did you reuse the clip on the intermediate shaft?? my axle didnt come with a new one
@timidater4803
4 жыл бұрын
@@themarginalmechanic5928 on the 06 sedona, there is a c clip on the intermediate shaft that the outside axle slides over, I cant get the axle to go back over it
@BugzKiller
2 ай бұрын
Did you reuse the old spring clip then? I got my new axle and it also did not come with a new one.!! Please reply. Thanks!
@DeffectiveMirrors
5 жыл бұрын
I used a pry bar, never seen that chain method
@Sroor2023
5 жыл бұрын
Even me 🤣🤣🤣 he should make a movie while he doing this next time 😄😄😄
@Foggghunter
3 жыл бұрын
I'm assuming you need an alignment after this correct?
@themarginalmechanic5928
3 жыл бұрын
Changing an axle does not require the front end to be aligned unless for some reason you were forced to make changes to the length of the outer tie rod.
@Foggghunter
3 жыл бұрын
Thank you!
@mattspurgin6775
5 жыл бұрын
Did you do the driver side too,
@mattspurgin6775
5 жыл бұрын
what tool did you use to pry the driver side? I got everything separated but my inner cv boot is torn so it separated at the joint with the base still in the transmission and I didn't have any luck getting a pry bar in there to pry it out.
@Sroor2023
5 жыл бұрын
Where do you live its so rusty for brand New one year old part?
@YourAverageFNAF_Edits
Жыл бұрын
I like to use the chain with a 20lb weight disc
@vernonbosshard9317
11 ай бұрын
The carrier bearing is bad too. Do both.
@josephkober3734
Жыл бұрын
Your intermediate shaft splines are probably worn which is ruining the cv axle splines . I would replace the intermediate shaft also
@timidater4803
4 жыл бұрын
Never sieize much better than grease, although grease is better than nothing!
Пікірлер: 40