Done this a million times. But your descriptions are completely spot on . I usually don't work on ford products, but have to do the wife's edge this week. So I looked for a tiny refresher course. Great job on this video. Liked and followed.
@T-MillProductions
Жыл бұрын
Thank you very much friend! I try to be as descriptive as I can be. I’m just trying to help people as much as I can since shops charge an arm and a leg. I don’t mind doing these wheel bearings for the most part unless they’re super rusty and never been done before lol.
@MACTFordEdge
Жыл бұрын
Great job, Time consuming and less expensive if you have the tools. I usually bypass the press and just replace the entire knuckle with a brand new assembly complete with bearing, hub and new shield. Only takes short time to replace. Does cost more but much easier with the assembly if you do not have the tools and equipment. Nice Video.
@T-MillProductions
Жыл бұрын
How much are the complete knuckles? I’ve had this shop press for so long I try to get all the use out of it I can. But i totally agree the time wise a complete knuckle replacement is the way to go. Thanks for watching! And thanks for the nice comments
@T-MillProductions
Жыл бұрын
Oh that’s not bad at all
@99ronmarsh
2 ай бұрын
great video , I have to change the driver side , your video sure will help ! Thanks 👍
@T-MillProductions
2 ай бұрын
I’m glad it was helpful! Good luck with your project sir, thanks for watching!
@jesuspicorelli3286
9 ай бұрын
I used 2x2 wood and 38mm socket to put the bearing in there.
@T-MillProductions
9 ай бұрын
Good idea! I’ll try that next time
@CosmicFox808
Жыл бұрын
Wow, this looks like a BIG project. Respect to you!
@T-MillProductions
Жыл бұрын
It was lol. I was able to make 4 videos out of it. Had to do 3 projects at the same time.
@molly4046
Жыл бұрын
Nice job man! Glad you did this job, really helps out to see it all done from start to finish!
@T-MillProductions
Жыл бұрын
Thank you!
@elmerkerth3871
2 ай бұрын
That was a great video
@T-MillProductions
2 ай бұрын
Thank you for that nice comment!
@dalejrfan820002000
Жыл бұрын
Thanks for the good information. I just wondered how the studs stayed in? Lol. I'm surprised they didn't Pop out.
@T-MillProductions
Жыл бұрын
No problem man! I’m glad I was able to help you out! Yea they’re in there pretty good lol, all the years of salt and rust keeps them in there nice and tight
@fueledbymusic3
2 ай бұрын
I tried everything to remove that bearing on my 11 Edge. Despite of have ALL TOOLS I need! The press AND the wheel bearing removal kit. Did the job exactly how its supposed to do. The bearing just simply will NOT BUDGE OUT! I then tried to cut the bearing out with the cutting tool. STILL refuses to come off! It's like if some idiot welded or glued the stupid thing in. After spending several hours in hell. I called it quits. (Despite of have ALL tools I need). I'm just going to order the whole knuckle assembly. It's only $95 NEVER EVER seen anything like that with a "welded in" bearing
@T-MillProductions
2 ай бұрын
I’m sorry that happened to you man, I have seen that before on the rear wheel bearings on the old 04 style explorers. We had one at work that we took a torch too and left on the press all weekend and it simply wouldn’t come out no matter what we did. We did the same thing and just ordered a new knuckle for it. Sometimes that’s just the way to go. Are you up here in the salt belt or are you in a salt free climate?
@fueledbymusic3
2 ай бұрын
@T-MillProductions our car lived in California all it's life according to carfax. So I guess it does happen, hah. Stuck bearing. I thought I was tripping. 😆
@T-MillProductions
2 ай бұрын
@fueledbymusic3 wow I’m amazed in California that it would be seized in there like that lol
@syddd3642
Жыл бұрын
I always get nervous going on the ears of the knuckle i had an escape the bearing was stuck like a breeding dog and it snapped the ears right off little tip if you dont have snap ring pliers to get them out i use a little punch like you use to set nails get under it enough to get a screw driver then get a 2nd screwdriver walk it about half way and it will fly out
@T-MillProductions
Жыл бұрын
No kidding ? That had to be a scary scenario. You didn’t get hurt or anything did you? That’s a great tip! Thanks for the input, I’m glad you shared that with us. Years ago I tried a hammer and screw driver and that didn’t work lol
@fredobueno
Жыл бұрын
I took the bearing to get pressed in because the rental tools get bent if you try using those lol do you know if the bearing has to go in a certain way for ABS sensor?
@T-MillProductions
Жыл бұрын
Oh did you? I’ll tell you man the harbor freight shop press is wonderful for the money! The bearing is the same either way it goes in. The abs sensor runs off the tone ring on the axle shaft so you can put the bearing in either way. Hope this helps you out!
@fredobueno
Жыл бұрын
@@T-MillProductions lifesaver! I asked because they didn’t want to press it for me in case it didn’t work and I told them it uses the cv axle “ring.” It took some convincing. Could be cause I am young and to them, young is clueless. Dad taught me everything I know. Thanks for the reply!
@T-MillProductions
Жыл бұрын
Glad it all worked out for you friend! Hope you get her all fixed up, anytime man! Have a great one! Please subscribe if you found the video or myself helpful please I sure would appreciate it!
@pablohernandeznunez4474
Ай бұрын
Can a 6 ton press work?
@T-MillProductions
Ай бұрын
Honestly I’m not sure, it’s worth a try tho
@89G
Жыл бұрын
Curious... is this a FWD or AWD? I did my Brother's 2015 that is AWD, and it's a bearing/hub assemble held in with 4 bolts.
@T-MillProductions
Жыл бұрын
This is AWD, did you do the front or rear?
@89G
Жыл бұрын
@@T-MillProductions front. All 4 corners use the same bearing on his too.
@T-MillProductions
Жыл бұрын
I will need to change the title then, apparently my fact checker was incorrect. Thank you for pointing this out!
@89G
Жыл бұрын
@@T-MillProductions I was just thinking that you had an AWD. I jus did a video on his 2015 a couple months ago.... but figured Ford did the FWD different. The style your doing is just like my Escape's (200 and 2011) though....
@T-MillProductions
Жыл бұрын
Oh okay, I don’t know why ford does that stupid crap for , why not just have the typical hub bearing with 4 bolts and be done
@eveliaramirez8125
2 ай бұрын
como caviar elbalero delas Rueda deatras de una edge 20 14 ford
@T-MillProductions
2 ай бұрын
Thank you
@Mrkouman
10 ай бұрын
Im surprised the brake caliper ears didnt bend enough to effect the caliper to brake rotor..
@T-MillProductions
10 ай бұрын
Na that cast is strong and the bearing came right out. If the bearing was seized in the knuckle then that would be a different story
@Mrkouman
10 ай бұрын
@@T-MillProductionsI'm glad it didn't but customers usually don't catch it early enough until the bearing is heat welded to the knuckle, it's worth a try it will be just my luck I'm gonna need a knuckle
@T-MillProductions
10 ай бұрын
@Mrkouman I hope it works out for you too and doesn’t mess it up. Mine all came out just fine over the years thankfully. I did have an explorer once that had it seized in the rear knuckle. If you need any help or advice please feel free to ask me or anyone else on here. I try to promote everyone to help everyone out. Also thank you for watching my video I appreciate the support!
@Mrkouman
10 ай бұрын
@@T-MillProductions I usually get it out with the press or hub shocker, this car the hubs are wider than any typical press and cannot fit stable unless there's all kinds of adapters used like you did. I just prefer to mount the braces closer to the knuckle than the ears of the knuckle. If all else fails I'll have to use the ears
@T-MillProductions
10 ай бұрын
@Mrkouman oh okay, yea these knuckles aren’t that good of a design. I had to play with it for a while to figure out a way to get it to sit flat and press the old one out. Hopefully yours goes smooth
@kenny4813
10 ай бұрын
would of been nice to let us know there are two different types of wheel Bearings... got all the way put back together watching your video and come to find out the wheel bearing hub is to big for my wheel to set centered ... so now i have to borrow my inlaws vehicle until the autoparts store gets the correct one in... i know its not your fault just would of been nice is all
@T-MillProductions
10 ай бұрын
I didn’t know that actually, so I’m confused, how is the bearing wrong if you ordered it for you specific vehicle?
@kenny4813
10 ай бұрын
@@T-MillProductions different part number for allwheel drive, the part number i ordered was 517518 still awaiting the correct one
@T-MillProductions
10 ай бұрын
Interesting, I never knew that myself
@Rbenterprises4
Ай бұрын
Why not replace the hub and brg assembly instead of all that labor?
@T-MillProductions
Ай бұрын
What do you mean? This is a press in bearing so you have to press the hub into the bearing regardless if you replace it with a new one or not. Do you mean a knuckle? As far as buying a knuckle with the bearing and hub already pre installed?
@Rbenterprises4
Ай бұрын
OReilly sells the Dorman loaded knuckle and hub assembly, but it is pricey!
@T-MillProductions
Ай бұрын
I thought about that but honestly I press bearing in so much it’s second nature lol
@Rbenterprises4
Ай бұрын
I understand. In Texas labor rates are pretty pricey, so as a DIY'R I do most of my own work. Nice video! Thanks!
@T-MillProductions
Ай бұрын
@Rbenterprises4 I get that, up here in Wi they’re pretty bad too, I’ve actually changed these bearings a few times. Cheap ones off rockauto didn’t last so I got some other ones I’m trying now
Пікірлер: 72