That's the "Camshaft" position sensor the exhaust camshaft, there's also intake one. The crankshaft sensor is above the starter solenoid.
@KurtHite
4 жыл бұрын
@Brad can you please update the title. This is the Exhaust Cam Sensor. Calling it a crank sensor made this video so hard to find. This sensor is at the top back left of the cylinder head (measuring the exhaust cam sensor) There is no crank sensor in the cylinder head. I see you mentioned that to someone in another comment (that this is a cam sensor) but for some reason the title is still wrong. Thanks for the video though
@lemonaid8678
4 жыл бұрын
Kurt H i was wondering if anyone else noticed that was a cam sensor..
@KurtHite
4 жыл бұрын
@@lemonaid8678 someone did a while ago but the title wasn't updated. So I asked again. Also FWIW I actually did it with just a 3or4" extension on a 1/4 drive small ratchet
@lemonaid8678
4 жыл бұрын
Kurt H the cam sensor? Or the crank I’ve already replaced both cam sensors and cam valves on top of the motor. Where is the crank sensor located? Some people are saying behind the heat shield on the exhaust side. Some are saying I gotta remove the starter.
@lemonaid8678
4 жыл бұрын
Kurt H nvm I found it have to remove the starter.
@KurtHite
4 жыл бұрын
@@lemonaid8678 the Crank Sensor is on the block at the front of the engine slightly above and behind the Starter. You remove the starter for easy access. There seems to be a problem with everyone mislabeling the sensors on these engines. Cam sensors like this one shown there are 2x one at the back side of the engine and one in the front just below the high pressure fuel pump. Both in the cylinder head since they are reading the cam. Crank Sensor is in the engine block. This vehicle has it located right near bell housing of the starter motor. Last are the VVT solenoids (cam solenoids) often being called cam sensors by mistake in many videos. They are at the top of the engine on passenger side. Located in the valley of the valve cover at the far passenger side of motor. They are by far the easiest to replace.
@jamesrichardson771
Жыл бұрын
Thanks a lot my friend (I gave up) on the rear one. managed to replace the "front" one... I'll Try this "from the bottom" method 👍🛠
@Fazel_Patel
Жыл бұрын
P0366 [0x0366] Camshaft position (CMP) sensor B Good video. I’m having hell of a time accessing the bolt to remove sensor. Wasted so much time. I’ll try from bottom.
@ekrupa2
7 жыл бұрын
Great video...thanks for posting. Took me less than 20 minutes to replace.
@poodlebarf3787
Жыл бұрын
I used a socket wrench with a pivoting head from the top. Was extremely easy
@janewebb498
7 жыл бұрын
Was your equinox stalling when you would come to a stop and then try to accelerate? That is the problem I'm having right now and every forum I find with ppl having the same problem say it's the Cam actuator sensor.
@Brad-cd5fw
7 жыл бұрын
Yes it was I changed the camshaft sensor but the car was still stalling and I had to change the intake sensor p0011 code it camshaft position actuator solenoid valve. I have another video showing how to change it too. Hope that will help you
@janewebb498
7 жыл бұрын
Roughandtough thank you so much. I'm gonna give this a try and hope for the best.
@anslempierre6579
4 жыл бұрын
I replaced the crankshaft spark plugs and ignition coils
@khalilkhalaf712
4 жыл бұрын
I did not see anything from the video. Where the sensor is, which side did he go under the car... Help?
@Brad-cd5fw
4 жыл бұрын
Went under the driver side
@annastasiamartin5569
7 жыл бұрын
Thank you for this video!!!!! seriously thank a million times (:
@Cycleman61
7 жыл бұрын
Sorry, I retract that. My mistake.
@chrismathius
7 жыл бұрын
thanks boss man very helpful!!!!
@anslempierre6579
4 жыл бұрын
I got a code p0011 over advance timing I changed the intake a few months back should I replace the outtake solenoid too or is it the sensor I also have code p0341 p0366 p0335
@eltequilero2000
3 жыл бұрын
Crankshaft position sensor or camshaft position sensor... ?
@Brad-cd5fw
3 жыл бұрын
Its the crankshaft position sensor. I accidentally said camshaft.
@eltequilero2000
3 жыл бұрын
@@Brad-cd5fw thanks. Is a good video.. thanks again.
@MS-mx8yj
5 ай бұрын
@Brad-cd5fw that's the camshaft not the crankshaft.
@dixiegirl919397
Жыл бұрын
I rly needed to find the crankshaft sensor not the camshaft. the title of your video is wrong
@Merky_Squeeky
11 ай бұрын
Crankshaft (ckp) sensor is behind solenoid and starter . Its a bitch to get to unless you remove the starter . You also have to have it "relarned" after you replace it apparently .
@Cycleman61
7 жыл бұрын
You should revise your title and audio. You just replaced the crank shaft sensor, not the cam shaft sensor.
@Brad-cd5fw
7 жыл бұрын
Yes the camshaft sensor. The crankshaft sensor is behind the starter you will have to remove the starter to get to as I can tell
@KurtHite
4 жыл бұрын
Ron this was the exhaust cam sensor... the Crank sensor is elsewhere (in the engine block. If you notice the sensor he replaces in this video is on the back top of the cylinder head. There is no crankshaft at the top back left of a cylinder head on any car.
@Blockizhott214
Жыл бұрын
So is it the camshaft he is changing?
@Merky_Squeeky
11 ай бұрын
Yes
@fullsizechino6278
2 жыл бұрын
This is the cam not crank
@champ18d
5 жыл бұрын
I have a code for p0014 exhaust camshaft position timing- over advanced (bank 1) I already changed the exhaust engine variable solenoid but still have the code. should I change this part to clear the code?
@Brad-cd5fw
5 жыл бұрын
No code won't always clear out you might have to go to the parts store and see if they have a code reader to clear the code it usually Free to do it. But remember to check the code reader again cause sometimes p0014 mean intake or exhaust cam sensor or something like that there on top of the motor and I see it come as p0013 I some cases I hope this helps you.
@Brad-cd5fw
5 жыл бұрын
Yes try to changing the part to see what does. It ever hurt to try.
@armaniwilliams5510
6 жыл бұрын
What does cam shaft sensor do
@Brad-cd5fw
6 жыл бұрын
A crank sensor is an electronic device used in an internal combustion engine, both petrol and diesel, to monitor the position or rotational speed of the crankshaft. This information is used by engine management systems to control the fuel injection or the ignition system timing and other engine parameters. Before electronic crank sensors were available, the distributor would have to be manually adjusted to a timing mark on petrol engines.
Пікірлер: 45