Thanks for watching. MORE DETAILED VIDEOS ON THE CHANNEL IF YOU MISSED SOMETHING
@ChiefDLK
3 ай бұрын
I've pulled my transmission several times and am about to do it again for a rebuild. It always takes longer. I don't have a lift so I am stuck doing it on the ground which adds a lot of getting up and down off the ground. The standing up and laying down is the worst part of having to do it. I like the order you did the removal, so I will likely incorporate that into how I do it this weekend.
@mechanicgray
3 ай бұрын
I agree. Doing this on the ground is twice as hard. Good luck. 👍
@TonyG-z6i
18 күн бұрын
Hey bud did you have to download the memory there re install them back after putting everything back in service?
@mechanicgray
18 күн бұрын
If you use the same Transmission control Module you don't have to reprogram it. If you get a new or different one you need to program it to the vehicle. It is inside the Transmission.
@TonyG-z6i
17 күн бұрын
@@mechanicgrayyes I'm buying another rebuilt one ,what do I use to download the program?
@mechanicgray
17 күн бұрын
@@TonyG-z6i You need to find a mobile programmer or take it to the dealer. Your local Trans shop can point you in the right direction, mabey they can do it. We have a mobile programmer that comes and does ours.
@MattsGarage
4 ай бұрын
First, thank you. This is extremely helpful. Second, where do you find those slide in adapters for the transmission jack head that create those vertical standoffs for the oil pan bolt rail flange? I can't find them anywhere!
@mechanicgray
4 ай бұрын
Hey no problem. I'm not sure where we got them. I'll ask and let you know.
@ethansime3874
8 күн бұрын
Dude get safety glasses
@mechanicgray
7 күн бұрын
I have some for when I'm grinding ect.
@sbirddesmo
5 ай бұрын
Starting a pull on a '17 for a friend today. I'm going to do what you did. Thanks much!
@mechanicgray
5 ай бұрын
Hope it helps. If you have questions put them here and I will respond. 🤘
@jamesethan3749
Ай бұрын
Cant see shit 99% of the time but thanks for the video
@mechanicgray
Ай бұрын
@@jamesethan3749 I have detailed ones of the same Transmission pull. This was just a no cuts video. 👍
@jamesethan3749
Ай бұрын
@@mechanicgray brother since ure so helpful and respond quick, can u gimme a tip where the vent hose end goes the one that goes up into the engine? Im installing mine rn, one hose onto tranny tube, second end just hanging off the transfer case, but where does the 3rd end go? Turned all internet upside down cant find answer.
@mechanicgray
Ай бұрын
@@jamesethan3749 One hose from the transfer case to the bracket on the top bell housing bolt. Second hose goes from Trans vent to a plastic tee. Then one end goes up to said bracket the other end usually goes the a clip on the crossmember.
@mechanicgray
Ай бұрын
Check out the video from a couple weeks ago. 2019 Silverado. It's the same and you can see the hoses.
@jamesethan3749
Ай бұрын
@@mechanicgray thank u bro ill watch ur vid and re-read your explanation when i get back to the car tomorrow
@kill3rhorsepow3r51
7 ай бұрын
Ayyy farmers repair coming in clutch to aid in my install 🙌🏻 prolly be easier to have yall install my new one 😅
@JuseJamez
3 ай бұрын
Cheverlot has swapped my trans twice. 2nd time it was under warranty. The first time it was 3 days after an oil change which had me puzzled. It was working fine until that oil change. Now… 3 weeks after that transmission swap. 3 bolts have broken and my engine makes a weird noise. 3500 dollars. I need a bicycle.
@mechanicgray
3 ай бұрын
Damn that sucks. Don't think the oil change had to do with it. Sometimes stuff just happens at wired times.
@waynethompson8306
3 ай бұрын
16:55 great uncut video of the trans, thank you. Question do you need to learn/read the old trans and write to the new one on the 6L 80?
@mechanicgray
3 ай бұрын
Yes. If you change the transmission it needs to be programmed.
@thegonz7833
Ай бұрын
I rotate the engine in the direction it runs to prevent a water pump fails. You made it look easy and quick, i was watching to see what you did with big harness as it came down. I guess it stays with the fuel lines?
@mechanicgray
Ай бұрын
@@thegonz7833 The water pump will fail if it turns backwards?
@thegonz7833
25 күн бұрын
@@mechanicgray Ive had it happen twice on LS
@jakeowens1770
6 ай бұрын
Trashy 🎶 🎵
@sbg4422
Ай бұрын
thank you bro this helps me remove my 6.2 that seized at the crank.
@mechanicgray
Ай бұрын
@@sbg4422 👍
@jessetorres6317
6 ай бұрын
Does the truck have to be left in neutral to spin the motor and remove convertor bolts?
@mechanicgray
6 ай бұрын
No. I do put it in neutral though to be able to turn the drive shaft so its easier to take the bolts out.
@elmerkerth3871
4 ай бұрын
I like watching your video seems like I might be able to take mine out
@mechanicgray
4 ай бұрын
Thanks 👍 Hope it helps
@devongrubb9634
7 ай бұрын
“Then I go get a buddy to help lower it down” 😂😂😂😂cuhmon buddy it’s like a 80 pound t case at most.
@mechanicgray
7 ай бұрын
Im only 155. 80 is enough 😂😂😂
@thenotsojollyrancher-akate9516
6 ай бұрын
You can put a strap on it and over the torsion bar support and slowly let down by strap.
@djladd241
2 ай бұрын
Do you have a video of reinstalling this 6L80 or similar transmission?
@mechanicgray
2 ай бұрын
I do not sorry. Same process just reverse.
@mechanicgray
Ай бұрын
Yo Yo. Ive got a install video going live at 4pm. Thought I'd let you know. 🤘
@ivanvega6071
8 ай бұрын
Is it possible to replace the plug in on the transmission?
@mechanicgray
8 ай бұрын
Yes. It's part of the valve body harness that is located in the pan.
@nolankeffer3099
10 ай бұрын
Perfect this is what im talking about great video!
@mechanicgray
10 ай бұрын
Thank you for watching
@brandeneskridge2318
5 ай бұрын
When you put a brand new transmission in a 2015 Silverado 1500, does the new transmission have to be programmed to the vehicle? I heard someone say it does, but idk for sure. Reason for asking, my trans is going out and I wanna know ahead of time. Thanks in advance!
@mechanicgray
5 ай бұрын
Yes. The TCM is inside the Transmission and will need to be programmed to the truck. If you are doing the job yourself make sure you also flush the transmission cooler. The most common problem with these is the torque converter fails. It then puts a bunch of metal in the cooler.
@Thep352
7 ай бұрын
Thank you so much for this video man
@mechanicgray
7 ай бұрын
My pleasure. Thanks for watching.
@yawningdoodle
5 ай бұрын
Was this a 5.3 or a 4.3 engine?
@mechanicgray
5 ай бұрын
5.3L
@phillipdrake4371
7 ай бұрын
I don’t like the way you lifted the truck the arms facing the same way, did you do that on purpose or you never have a problem with the lift ?
@mechanicgray
7 ай бұрын
Not sure what you mean
@phillipdrake4371
7 ай бұрын
The lift arms facing same way
@phillipdrake4371
7 ай бұрын
I’m doing a tranny in a 2020 4wd Silverado same set up as your video thanks for the video
@mechanicgray
7 ай бұрын
@@phillipdrake4371 You welcome. Thanks for watching.
@dl1015
4 ай бұрын
2017 does it need to be programmed
@dl1015
4 ай бұрын
It’s a manufactured transmission
@mechanicgray
4 ай бұрын
Yes it will need to be programmed.
@dl1015
4 ай бұрын
So I would need to take it to a dealership after the new manufacture transmission is installed
@dl1015
4 ай бұрын
@@mechanicgray I would need to take it to a dealership after installing a new manufacturer transmission
@mechanicgray
4 ай бұрын
@@dl1015 Or find a mobile programmer in your area. A nearby transmission shop should know someone. 👍
Пікірлер: 70