Yes, I had a brand new Mavic two pro a couple of years ago, and at one week old it flew by itself into the outrigger of a boat and that was it. And now I have another used Mavic two Pro and it’s constant.
@Kayshots
3 жыл бұрын
I had same. Not near powerlines, No magnets near, No antennas, Just 3km in nowhere. It started saying this. I flew back, Only if i point the camera at 1 Direction it happens, It’s still stable and it also said compass error. I pointed it to the exact location and calibrated it, It seemed to be fine. But i’m just wondering. I think it’s because of the sun, Sun has frequence waves. There’s a app to check them, But when the sun is bright, It has more powerfull waves that will most likely interfere, Also. When you get this, RETURN IN SPORT MOSE ASAP! this can get your drone to lose connection and flyaway! I was lucky but you won’t know how severe the interference is!
@michaelwood5519
3 жыл бұрын
Could be aliens too, they like to screw around with us when we buy drones. Sombitches!! I have the same damn error.
@GadgetReviewVideos
7 жыл бұрын
I had that error almost every time I turned it on after the firmware update from 2-14-17 so I rolled back a version. I just updated today to the latest firmware, the one after the 2-14 one and recalibrate the IMU and everything seems fine. But I heard you need to do the IMU calibration outside away from things in the house that could cause interference?? Make sure the surface it flat with a level in all directions. And also looking at your controller, I would point the antennas away a little at a 45 degree angle, not straight up. Make sure they are both pointing up at the same angle also. I would also unplug the phone, and see if the message still shows up. If it goes away it might be something with your phone cussing the interference. In this case try turning off Bluetooth and wifi and out the phone back and restart the controller. If it's still shows up maybe your phone has a magnet for a Smart Cover switch to turn the screen on and off. Then try a normal USB cable with the USB port, and turn the phone facing the other direction with the home buttons on the right side using the regular phone cable and USB port on the back of the controller. Good luck.
@TonyOlsenFerris
7 жыл бұрын
Yes, I heard that radio interference can interfere with calibration. I've discovered that you can use the realtime radio interference meters shown in the DJI Go4 to detect exactly what/where the interference is and move away from it - pretty neat. :-)
@Kayshots
3 жыл бұрын
@@TonyOlsenFerris Where in the app?
@michaelwood5519
3 жыл бұрын
@@Kayshots Just to the left bottom and upper limits of nowhere. Damn these things are high tech!! Fix my error please!!!
@marjorievanilette9020
7 жыл бұрын
Same problem here. Tried many things but same issu. DJI support does not give answer. Considering the price of the device it is deplorable !
@Alvin-eq5rc
5 жыл бұрын
Marjorie Vanilette update both remote and drone using the DJI assistant desktop app work for me. Make sure they’re the latest or refresh it.
@Kayshots
3 жыл бұрын
Calibrate and get latest Firmware
@joesimpkin6021
Жыл бұрын
I've done everything imaginable and still have this problem. Drone is unusable. Wouldn't recommend dji to anyone unless you want a paper weight.
@Alvin-eq5rc
5 жыл бұрын
I had this problem however both of my compass appear to be working. To those looking for solution, you could try connecting both your drone and remote to DJI assistant app and manually update to the latest firmware. That seems to work for me. And of course, you have to recalibrate it.
@claudiubirauas5206
5 жыл бұрын
Yes, it's true. I can make a direct comparison between first Mavic and the Mavic 2 Pro. I guss I had to calibrate the first Mavic twice or so, as on the Mavic 2 Pro it 's persisting almost everytime I start it up. I fly mostly outside, it has nothing to do with pwerlines or any cell towers. Even after recalibrating, it works fine until the next start... M2Pro seems to be more sensitive to mag interference, even from own unshielded components.
@davidchristie4879
7 жыл бұрын
I am having the same issue - just trying to get my Mavic up and running
@LKGMADMAX1
7 жыл бұрын
David Christie Brand new out of the box yesterday, I've tried and tried still getting the issue, messages still appearing console never connects. Tried inside and outside same results. Has anyone found a resolution for this?
@KlutchGawd
6 жыл бұрын
saaaaaame
@rcshenanigans2734
6 жыл бұрын
My friend's son is having the same issue, new and right out of the box. I'm not impressed with DJI.
@Kayshots
3 жыл бұрын
You guys are propably in a High interference area, Not to worry. Interference is normal. I reccomend when it happens, Stay in the postion you get it in. Calibrate it, No issues anymore. I haven’t flown mine for a week and got this. Which was understandable. But i’m very satisfied!
@michaelwood5519
3 жыл бұрын
@@LKGMADMAX1 same!! I'm pissed off too! Ridiculous!
@johnallen7854
6 жыл бұрын
I had the same problem just yesterday, my Mavic set on a concrete park bench, I'm hoping that there was rebar in the bench. Windy today, I will check it out later...
@maddie49403
5 жыл бұрын
My phone is attached with controller but when we on 3rd step pair to aircraft that is not working
@seanmurphy8510
4 жыл бұрын
Did you resolve? I'm having same issue at third step, cannot connect. Some say to check settings, but cannot when cannot connect.
@maddie49403
4 жыл бұрын
@@seanmurphy8510 yes the problem was in charging point of phone was lot of dust in i clean it and everything ok again
@seanmurphy8510
4 жыл бұрын
@@maddie49403 I had to change to plug from usb on bottom of controller and it works now
@maddie49403
4 жыл бұрын
@@seanmurphy8510 o then grate friend
@gregzibro7287
5 жыл бұрын
I was having this issue too. I chatted with DJI support and after a few checks, my compass needed recalibration. Problem solved.
@TonyOlsenFerris
5 жыл бұрын
Yes, this was a lessons-learned for me too.
@vhdfvemaybay7025
6 жыл бұрын
I was reported to this error now how to different: Magnetic Field Interference Fly With Caution
@TonyOlsenFerris
6 жыл бұрын
This happens when the Mavic is too close to a large power source (light a computer, power lines, or other large electronic device. In the DJI Go4 app you can actually see the read-out of the interference and isolate which source location it is coming from.
@johnallen7854
6 жыл бұрын
Also had a bad sprocket connection when I replaced the camera/gimbal assembly, I found the loose connection and it worked fine after that. I suppose that connection giving me the magnetic interference message could be caused by that connection working loose. Just a thought...
@kurtiscommerce3999
6 ай бұрын
I just did the same and got the same message. I think you’re right
@BobHayesPhoto
7 жыл бұрын
just sent mine back to DJI. started getting this message after v 1.03.05 got worse after 1.03.055, I'd get it everywhere and the drone became a paperweight. I'll let you know what happens.
@TonyOlsenFerris
7 жыл бұрын
Mine was an environmental newbie issue... I happened to be around magnetic interference... and not having the legs extended was part of the problem.
@BobHayesPhoto
7 жыл бұрын
Mine was extended. I tried in multiple locations. After the firmware update, it just bricked. I bought it from BestBuy because they had it in stock when I wanted it, but had none in stock to exchange it for, so I had to send it to DJI for repair. I have DJI care refresh which should expedite repairs, as well. So I owned it for 3 days before it went to s**t, sent it back, which took four days, they marked it received, and it has been in a black hole for over a week. No updates in the online repair status, I've called twice, the first guy told me four days ago that it was being looked at and they were "downloading the logs" called today and I was told it has not been looked at, because they are moving their repair facility from one place to another (I don't care where). And they have a repair backlog. They can't get this to fly and they are releasing another smaller drone, too? I should have bought the GoPro. This is the WORST customer service ever.
@michaelwood5519
3 жыл бұрын
@@TonyOlsenFerris That's weird, cuz the picture on the controller shows the legs in the no fly position.
@michaelwood5519
3 жыл бұрын
@@BobHayesPhoto agreed!
@matthewjohn7989
2 ай бұрын
I nearly lost my drone
@anthonypaul5210
4 жыл бұрын
I was flying my Mavic two pro I have flown before this time I was out on a walking trail I couldn’t see anything on my screen I decided to fly it anyway since I had traveled just to fly here not sure what was happening but at about 150 feet away for me at about 100 feet up started acting funny and not wanting To turn back I sort of panicked and went into a tree To give you my best description the tree is trimmed for the next three years I gave it a haircut before coming crashing down broke every wing on the arms. MAG INTERF CHECK APP !!
@matthewjohn7989
2 ай бұрын
It happened bay an electric box
@vhdfvemaybay7025
6 жыл бұрын
Help Me!
@KEEPROLLINROLLINROLLINROLLINYO
6 жыл бұрын
yo u have to calibrate your compass yo
@fleekkhalifa2819
5 жыл бұрын
How u do that
@joestewart5692
4 жыл бұрын
lol @ yo boi....you u iz wite ...yo
@michaelwood5519
3 жыл бұрын
@@joestewart5692 White with chocolate inside?
@LilyWillow22
3 жыл бұрын
your apple watch
@michaelwood5519
3 жыл бұрын
Yes, I get drone errors on my apple watch. The message from DJI says....." Sorry you bought this drone after we screwed up the firmware, but if you wait a year, we might have another update that will cause more errors to pop up. This is all part of Covid 19 and the Great Reset by the hitler dude Klaus Schwab. What a loony fooker he is!!!
Пікірлер: 51