Good advice. Also - some people have a spare fuse link to put in and out, say if it’s your daily, but then you also go to the track.
@superfreestyle7943
4 жыл бұрын
That’s a great idea too!!
@staticej8-829
Жыл бұрын
Is that like a switch or some
@xanmage8755
Жыл бұрын
What is a fuse link
@koolioshit7229
4 ай бұрын
@@staticej8-829hes saying you just buy another fuse box, cut the stock one, and swap them when needed
@BrightResultsMedia
2 жыл бұрын
I love it when there’s no fake laughter or snarky inserts. Just good info with no fluff. Thanks man. Much appreciated.
@JoseyWales8178
3 жыл бұрын
That gyro in the center console can be done differently. That gyro has to do with the stability control as well as safety. You can cut one of the wires and add a switch to it which will allow you to shut it off whenever you want.
@Avg_weeb
9 күн бұрын
To hard i would rather just cut stuff
@JDMHaze
3 жыл бұрын
1:48. You're welcome, but thanks for this video being short, I've seen some 15+10 minute videos and I'm like dude it should not take that long to explain something that simple
@xxhadyxx1017
5 ай бұрын
Honestly I liked that info at the start
@KoukiTony7
3 жыл бұрын
My man. Short and simple 🙏🏼
@dman8389
2 жыл бұрын
Straight to the point! Awesome video
@JDMHaze
3 жыл бұрын
If you wanted to you could snippet and then solder on some small male/female connections. So you can do as you please
@samurai3446
2 жыл бұрын
This is the Best and only video showing the correct way to do this
@markschaff9503
Жыл бұрын
Wonderfully stated! Thank you for the great video!
@edgarramos2830
3 жыл бұрын
I’ve cut the fuzes you’ve shown and still no luck. I have a 05 and it dosent come with a yaw sensor and or vdc button. I’ve looked everywhere and still can’t seem to figure out how to fully disable my traction control.
@edgarramos2830
3 жыл бұрын
Although cutting the fuzes did kind of help but I still can’t fully break traction.
@aikonjapan
3 жыл бұрын
U sure u have an LSD? Some Zs i believe are open diff?
@drift240sx9
3 жыл бұрын
@@edgarramos2830 you probably have an open diff
@pushhrodd01
3 жыл бұрын
@@edgarramos2830 if you don’t have VDC or a yaw sensor you have a base model which means open diff which means shit
@brianz6155
3 жыл бұрын
valet mode on?
@rlknight57
3 жыл бұрын
Will the VDC and Slip lights on the dash light up after cutting the fuse?
@anselmoochoa6400
2 жыл бұрын
Did you get to try it?
@Z06Yahir
Жыл бұрын
Mine didn’t the only light lighting is abs
@yo-ly5eg
3 ай бұрын
@@Z06Yahir did it go away if you put in a different fuse?
@johnayy
2 жыл бұрын
yo i have a base model 06 350z and was wondering if cutting the abs fuse would be enough to go sideways, my old 03 had a TCS buttons and the base models don’t have a TCS button. Also would welding my diff interfere with the traction control because I am not able to turn it off since it has no button
@xretrofitme8582
Жыл бұрын
Would like to know as well
@blitz7522
8 ай бұрын
@@xretrofitme8582same
@avabanks9582
2 жыл бұрын
thank u!!! bouta go drifting needed this
@carterpritchard5063
3 ай бұрын
Wish I knew this last weekend at slushfest in Colorado, we couldn’t get the car sideways because of the traction control was still engaged gonna try this and see if it works
@yo-ly5eg
3 ай бұрын
did it work?
@carterpritchard5063
3 ай бұрын
@@yo-ly5eg I haven’t tried it yet was going to this weekend
@yo-ly5eg
3 ай бұрын
@@carterpritchard5063 lmk if I’d does and will you use a different fuse for a daily
@carterpritchard5063
Ай бұрын
@@yo-ly5egI completely forgot to reply to this, I remembered it just now so yeah, anyways it worked great just snipped the fuses like he said and now I can send it no problem
@yo-ly5eg
Ай бұрын
@@carterpritchard5063 can you do burnouts or only drifts?
@PeterSedlak-z7y
2 ай бұрын
In my 2006 I don’t have sensor inside the car what should I do ? Just cut thous 2 fuse ?
@r6ap6r6
3 жыл бұрын
thank you, all im saying is thank you
@flopydonkydick69
Жыл бұрын
Thanks for the straight forward video bro! Good job 👍
@Snapper408
3 ай бұрын
Wild this work for a 2003 fx35
@patricioovalle6590
Жыл бұрын
what about cutting pin 101?
@07ZX6R
4 ай бұрын
Did this now my speedo is disabled. Thanks 🙃
@SourceHitIt
3 жыл бұрын
If im not going to be tandeming, is it necessarily to pull the yaw sensor? I have an automatic and when I take it to the strip i can’t do a proper burnout as it limits my car to 3k rpms if im on the brake...is that the fuel cut you speak about?
@sanfordsonmail2334
Жыл бұрын
When driving on highway & hit something a little bump tracking kicks n & it won't go. I have to turn traction on manually to get it to go again. Is this what I need to do to my 06 automatic ?
@BradFFA
3 жыл бұрын
Just did all these steps she gets wild
@BradFFA
3 жыл бұрын
Guys i take back the comment I did everything and can’t do a stand still burn out
@superfreestyle7943
3 жыл бұрын
You will need to clip the brake signal wire going to your ecu to do stand still burnouts... this video just covers disabling the traction control system
@smithboy89450
3 жыл бұрын
@@superfreestyle7943 I have a 08 and I cannot find anything about the pinout for that brake wire cut everyone just says pull the fuse but I’m just looking to permanently delete it
@SamAdvenMedia
Жыл бұрын
@2:33 I feel attacked! I still have my 240sx though
@andrewguerra744
Жыл бұрын
You no I accidently got the exact same lights comming on in my dash and I don't know how to turn them off now lol. I think I need to replace wheel speed sensors??? Please help
@matthewrobb3739
10 ай бұрын
The best .sound natural
@metroh59
2 ай бұрын
I have a 2008 350z and cannot find the yaw sensor under the center console, is there any other place it would be? Also what models of a 2008 350z come with VDC?
@PeterSedlak-z7y
2 ай бұрын
Same problem
@HungryYett
3 жыл бұрын
So you just cut those two wires in the fuse box?
@carloscervantes7781
Жыл бұрын
When you remove them ? Are the lights going away ? Or that’s for the lights to be on forever ?
@barneylong1390
2 жыл бұрын
is there anyway to do this without permanently disabling traction control, abs etc
@djbiggzvendettasound7470
Жыл бұрын
Or will you still see that TCS and SLIP WARNING?
@_skiin
2 ай бұрын
Will this disable abs on a infinite m45s with vds ? 1:30
@VqMichael
Жыл бұрын
When I cut my fuses and all it did was turn on the light in the dash but when I tried sliding it it felt like it still had traction control on any suggestions?
@2MOROGARAGE
10 ай бұрын
Driver mod
@quocd5580
6 ай бұрын
Useful +1
@drift240sx9
Жыл бұрын
So does the speedo still work after doing that
@Gabriel83580
3 жыл бұрын
In your opinion what do you think would be making those same cluster lights come on in my car if I haven't done anything to the fuse or fuses?
@EdMatthewsPhoto
3 жыл бұрын
I'd see if there are any codes on the OBD
@Glyroth
2 жыл бұрын
Mine just happened the abs tcs and slip light all turned on I’ve seen a couple forums but I’m not to sure did you fix yours?
@Gabriel83580
2 жыл бұрын
@@Glyroth no I haven't yet,if I turn the car on the lights are not on if it rolls in neutral they stay off, it's only when it starts to move in drive/first gear then they come on and stay on. I've checked every single fuse in the fuse boxes available in the z. So my guess is it's a sensor or something that's called the Yah controller.
@Glyroth
2 жыл бұрын
@@Gabriel83580 what I have heard it’s the abs speed sensors behind the rotors I changed my ball joints yesterday and I think I must of stretched the tire a little to much and they stay on when I start the car and I can do burnouts now while left foot braking
@Gabriel83580
2 жыл бұрын
@@Glyroth you talking about the rear wheel rotor sensors?
@Sy3bolZ
Жыл бұрын
Will this impact the car in anyway ??
@DerbiCrewSM
Жыл бұрын
The fact thay you knew i switched from a 240sx to a 350z was pretty funny😂
@saeedghanbari7573
Жыл бұрын
This is not a proper method. I got lights in the dash and service engine as well. I scanned the car with OBD scanner and got 6 errors including P2122. The ECU put car in "risk mode" and reduced the engine power. any better ways to do it guys?
@juandlugka
7 ай бұрын
He literally said to disconnect the sensor or it’d go into limp mode
@evanflores2804
2 жыл бұрын
my z is my daily 07 hr would anyone recommend that i don’t do this for the daily or should i just shoot for the stars baby?
@mcampbellecu
2 жыл бұрын
Don’t
@Z06Yahir
Жыл бұрын
i have an 07 too, by any chance do you have the vdc button? because i don’t, i recently cut the abs fuse like the one in the video and it’s a little better, but im scared to keep driving so i bought a new fuse.
@joshualight3644
Жыл бұрын
So what if it’s not a vdc car?
@djbiggzvendettasound7470
Жыл бұрын
Does this erase the lights off the dash gauge?
@sergioa9097
3 жыл бұрын
Can a button be wired to the fuse the turn on and off in the cabin of the 350z ?
@superfreestyle7943
3 жыл бұрын
Yes... I normally work on dedicated track cars where it doesn’t matter but I have had customers ask for it to be done this way for cars that are primarily driven on the street
@sergioa9097
3 жыл бұрын
@@superfreestyle7943 wow thank you so much for clarifying that ! I'm planning on making 3 switch. 1st abs fuse, 2nd abs fuse, 3rd Pin101
@Z33Garage
4 жыл бұрын
So how does this compare with pin 101 cut mod?
@superfreestyle7943
4 жыл бұрын
Pin 101 is for throttle cut when braking, its actually not part of the traction control or driver assist functionality... It will cut throttle duty cycle when left foot braking and is a great idea to disable for a tandem or competition car.. I actually plan to do another video covering it since de and hr use a different pin location
@Z33Garage
4 жыл бұрын
@@superfreestyle7943 ok good info, so for track use it's probably best to have both of these mods done I imaging.
@superfreestyle7943
4 жыл бұрын
Correct
@smithboy89450
3 жыл бұрын
@@superfreestyle7943 can you do that vide because their is literally nothing online for hr cars
@sergioa9097
3 жыл бұрын
@@smithboy89450 Yooo! I'm saying! I looked everywhere and found nothing on HR "Pin 101" since it's not actually #101 on the ecu
@sonnyp3228
3 жыл бұрын
my 350z sit in the garage not touch in two week, why the TCS anf SLIP light on?
@alonechaos
2 жыл бұрын
Have you found out I'm having this issue
@lukebryant3899
2 жыл бұрын
Damn me too
@nickgnimng
3 жыл бұрын
Do I have to disconnect the battery before doin all this ?
@ShiftyReaperGaming
3 жыл бұрын
I don’t think it’ll make a huge difference but better safe then sorry I would won’t hurt anything to do it. Smart move.
@anthonysavage6155
3 жыл бұрын
Do brake lights still work?
@superfreestyle7943
3 жыл бұрын
Yes sir
@anthonysavage6155
3 жыл бұрын
@@superfreestyle7943 thank you thank you. Im currently attending a memorial burnout drive by for a friend of a friend that passed. Perfect day for this thank you. Already made sure it worked after i clipped em. Thank you
@JDMHaze
3 жыл бұрын
brake lights are tied to an entirely different fuse lol
@grassrootdigital3772
4 жыл бұрын
Hey bro, heard around the 30 second mark that you like porn here’s a link
@typicaltilly2535
3 жыл бұрын
The fact this is necessary to disable it makes me not want one. I want the TC for driving in rain and daily driving
@ccdog2002
3 жыл бұрын
Have a spare fuse to chuck in there then simple
@RocPackk
3 жыл бұрын
@@ccdog2002 where can I buy a spare fuse?
@TehKairo
3 жыл бұрын
@@RocPackk literally any autoparts store, any nissan, online too lol
@informKPBoateng
3 жыл бұрын
@@ccdog2002 just got one on amazon for $12
@gordonmcfarlane9346
2 жыл бұрын
@@informKPBoateng what did you search for can you share the link
Пікірлер: 112