We get excellent patterns out of 2.75's Sometimes they out pattern the 3's and they're faster so more downrange performance! Always great videos from Mr Roger
@kennethtephabock5634
2 жыл бұрын
Great video
@michaelbarrett2346
3 жыл бұрын
Great information, thank you
@FranksAFreeman-pe6oq
4 ай бұрын
Does the MG 42 and the short shell wad work well in tapered hulls? Or are they only meant for straight walls?. I have a huge garbage bag full of old Remington number eight Hulls. They are essentially. identical, two golden gun club hulls.
@huxmetalworks7371
2 жыл бұрын
Great job very good work thanks for sharing can you or do you have any videos on 23/4 low brass new to reloading thanks for sharing
@travisweldmaster7815
Жыл бұрын
Brass height means ZERO
@What_Fred_Said
2 жыл бұрын
What do you shoot with this load? I like #4 shot for squirrels 🐿 Is this your self defense load? Just curious as to what your shooting with these loads.
@rogeradkins9146
2 жыл бұрын
These were buckshot loads for deer hunting
@raycar1747
Жыл бұрын
Yes they are for self defense, Shooting a deer with that load, Will be a wounded deer that will die and never be Found. !!!
@KeithRollings-n2b
Жыл бұрын
To make a rolled crimp, how high should your payload be from the top?
@garygwd54
2 жыл бұрын
have you tried these with the Fiocchi 2 3/4?
@mrcrackernuts
2 жыл бұрын
I have loaded 10 pellets of 33 cal 00 in the green short wad in the grey 2 3/4 Winchester aa hulls. Seem to work great. I have read the aa are tapered hulls. Would you see a problem loading these or would you stick to hulls like federals?
@raycar1747
Жыл бұрын
Straight wall wad in a Tapered hull Is a no-no.
@thastinger345
Жыл бұрын
The Gualandi wads work fine in taper wall hulls (Rem STS/AA etc), but some mica wad slick really helps the process. The same wads fit much easier into the Federal hulls though, but it takes 3 more grains of powder in the straight wall hulls to get the same velocities as the taper wall hulls produce.
@Goodnightandgoodluck-c7m
2 жыл бұрын
I'm new so just clarifying, what wads was used? Thanks
@johnwalters7415
Жыл бұрын
I have a question can you load #4 bird shot in 2 3/4 hulls and the 1138 wads.
@thastinger345
Жыл бұрын
long as it is lead shot, yes
@zacharyjones1657
2 жыл бұрын
When I pull lee load all the whole way down on the crimp it keeps buckling the hull around the bottom. Is there a way to fix this or just don't push down so hard
@rogeradkins9146
2 жыл бұрын
It's a feel machine you don't have to pull down real hard, pull down easy an look if more is needed pull down again slightly harder , sounds like your pulling down too hard
@zacharyjones1657
2 жыл бұрын
@@rogeradkins9146 that's what I thought. Still kinda new to reloading so I guess keep practicing and will find the sweet spot. Thank you for answering
@raycar1747
Жыл бұрын
Trash that Lee and get a Mec 600 Jr.
@jakeaddy1742
3 жыл бұрын
What speed do I need to run for the single pin roll crimper in your opinion
@rogeradkins9146
3 жыл бұрын
Lowest rpm
@johnwalters7415
Жыл бұрын
Is it ok to use steel shot wads with lead shot?
@rogeradkins9146
Жыл бұрын
yes
@lukefenech
3 жыл бұрын
What's your opinion on ideal distance from top of payload to tip of the hull mouth for good fold crimps?
@rogeradkins9146
3 жыл бұрын
Need at least 1/4 inch
@lukefenech
3 жыл бұрын
@@rogeradkins9146 Thanks Roger, I was expecting that you'd need more than that. I appreciate it.
@raycar1747
Жыл бұрын
@@rogeradkins9146 You need 1/2 inch to approve a good fold, not 1/4 inch. !!!
@rogeradkins9146
Жыл бұрын
@RAY CAR a new hull is exactly 3 inches long once complete its 2 3/4 inches long by my arithmetic that's a 1/4 inch fold
@raycar1747
Жыл бұрын
A 2 3/4 hull is 2 3/4 inch long new or fired, A loaded factory round is 2 5/16 long, so If my math is correct that is 1/16 from being 1/2 inches, so you do the Arithmetic. !!
@toddgover1447
2 жыл бұрын
What primers you using in the 2 3/4 federal buckshot hull
@rogeradkins9146
2 жыл бұрын
Winchester 209 or cheddite
@raycar1747
Жыл бұрын
If you use a cheddite Then you will have to recondition the primer pocket to go back with a American Primer, Cause the Cheddite will make the primer pocket bigger.
Пікірлер: 37