Great video and removed it with no issues as you described. So now I want to order a matching pump, were can I find the part number of pump? I see a number on pump casing on the outside and inside. The previous owner had transmission rebuilt but did not install correctly and broke pump tangs off for converter engagement.
@PerformaBuiltTransmissions
Жыл бұрын
You will have to go by the year make and model of your vehicle to get the appropriate pump style through any parts supplier
@swappedoutZ71
2 жыл бұрын
Looks like an easy process but I didn't know if you guys did custom work on the pumps or not.. can I just throw a new oem pump in my lvl2?
@PerformaBuiltTransmissions
2 жыл бұрын
We do alot the the pumps so no, an oem one will not perform near ehat ours do
@swappedoutZ71
2 жыл бұрын
@@PerformaBuiltTransmissions that's what I was figuring. Guess I will have to snatch it out and get it up there to you guys soon
@swappedoutZ71
2 жыл бұрын
@@PerformaBuiltTransmissions floored it from a 5mph roll and after spinning through first gear I lost all gears when it attempted to hit 2nd. I'm assuming it's the pump. No forward or reverse gears work and is making a slight whining noise. Happened yesterday. No leaks. Fluid is still red.
@PerformaBuiltTransmissions
2 жыл бұрын
You broke the pump. Your spacing was wrong on install or your flexplate is wornout and over flexing. All that ever breaks a pump.
@swappedoutZ71
2 жыл бұрын
@@PerformaBuiltTransmissions most likely flexplate I guess?? Been flooring the truck religiously for about 2 years and never had a single issue other than solenoids which is nothing out of the ordinary. So if spacing was wrong, how long would it last? That's what is leading me to believe it's the flexplate
@dong1453
4 жыл бұрын
What year was this transmission? I'm trying to replace the input speed sensor but nobody has a pump pull showing the sensor...???
@PerformaBuiltTransmissions
4 жыл бұрын
all you really do is unplug it and the rest stays attached to the pump when pulled. then its simply an 8mm bolt holding in the sensor on the backside of the pump.
@lm7bird680
3 жыл бұрын
Is this pump removal method possible without removing the bellhousing?
@PerformaBuiltTransmissions
3 жыл бұрын
yes but its very hard
@lm7bird680
3 жыл бұрын
@@PerformaBuiltTransmissions pump got stuck, had to remove the bellhousing. After that it came right out
@jerryc3201
5 жыл бұрын
Does the TCC go back in a certain way? Like can it be put on a half a turn off?
@PerformaBuiltTransmissions
5 жыл бұрын
im not sure by what you mean a half a turn off but yes they only go in one way
@jerryc3201
5 жыл бұрын
@@PerformaBuiltTransmissions if it goes in one way then I have no worries. What I meant was if it went in one way or you could flip it around 180° which is a half turn off
@jerryc3201
5 жыл бұрын
@@PerformaBuiltTransmissions I think I got it and I appreciate it you getting back to me.....thanks a lot
@PerformaBuiltTransmissions
5 жыл бұрын
No problem at all
@user-sl2fq9dv9g
Жыл бұрын
Is it possible missing the pump up while installing
@PerformaBuiltTransmissions
Жыл бұрын
You could clip the stator rings or misalign it
@ChivosGarage
4 жыл бұрын
Is this the same process on an 2008 2wd transmission
@PerformaBuiltTransmissions
4 жыл бұрын
yes except there is an additional ISS sensor you must unplug before pulling the pump.
@thomasbarnett2100
Жыл бұрын
Regarding doing this process on a 2009 9lpd. I need to change the pump. What all needs to be pulled from the valve body before I can attempt to pull the pump with out damage to any of the sensors. I know this is a long shot but any advice in them right direction would be much appreciated.
Пікірлер: 26