Mr Pandy your show always keeps a guy strong! You're attitude makes me still love this country.
@TristanBanwell
3 жыл бұрын
This was like watching myself on instant replay, except instead of hitting my fingers I bashed my elbow on the door latch. I just needed to see another human prove that the pin was in fact removable, and I got it done. Thank you!
@bugman2333
Жыл бұрын
Just dealing with this pressed pin now, it comes out pretty easy if you use an air hammer tool. Thanks for the vid.
@bicknellmanor8001
8 жыл бұрын
Thanks for the videos Wes, I feel your pain. I too, use a lot of PB blaster and never seize. Patience is what I lack most and I always fuss about the design of equipment that is so cumbersome to work on. Great video.
@matthewcloud119
8 жыл бұрын
nice video nice to see you do one at normal speed so we can actually see how you fixed it. thanks keep up great work
@brady8253
8 жыл бұрын
Constantly checking my subscriptions for a video of yours to show up!
@Mikeruf12
8 жыл бұрын
I did the same job on a 6400. I just used an air hammer to drive it in and out, worked great!
@RoisinT2
8 жыл бұрын
I screamed "side window!!!!!! nnooooOOOOOO...!!".. When you start to hit that :D I was sure it would soon just pop flying and smash that sideglass
@noahsimpson3484
3 жыл бұрын
Very useful you helped me out today tremendously on a 2011 6420
@lowercherty
8 жыл бұрын
Replace it with a bolt and nut so it will be easier next time? A little blue loctite and you're in business. That's about a five obscenity pin in a horrible location. Love your videos, can't wait to see the new bailer work this summer.
@Ham68229
8 жыл бұрын
+B Laquisha A bolt with a nylon-nut
@raykrv6a
8 жыл бұрын
Impressed you got it out that quick. Expected to hear swearing. I'ts part of the job.................
@shaunCNH
8 жыл бұрын
That Spring you found is supposed to be there. It is use to stop the handle bouncing about. If you don't have it in you'll get a rattle from that little handle when your driving about.
@shanehildebrand8255
8 жыл бұрын
the best penetrating oil is a 50-50 mix of acetone and atf. got to shake before each use but it's amazing
@radarwill
8 жыл бұрын
You sir are a mechanical guru!!
@ml2trick
8 жыл бұрын
Use the right tools for the job. You made a simple job' look hard. But nice Job. Great video. I cleaned my hands with industrial cleaners for 30 + years as a Marine Mechanic. Nothing more nasty" then burnt Gear oil.
@sap3055
4 жыл бұрын
I will ned to do the same shit on my jd 6430 and I'm not looking forward to it but you're vidz have been helpful
@gregorypiercesr.2769
8 жыл бұрын
next time with your punch clean up end and find socket that fits and get extension, gives you something to hold on to plus gets you in open area for better swing on hammer. the 50/50 acetone and ATF is killer stuff!
@dartman1965
8 жыл бұрын
Wes,a battery terminal puller makes a nice puller/press for small things.Get rid of the pb blaster and us kroil or atf and acetone mixed 50/50.
@ericsievers233
8 жыл бұрын
We don't use the pin at the bottom we put a bolt in. we have replaced those cheap things a few times.
@rickmatz4456
3 жыл бұрын
Mine is busted. One cold morning. How I miss my 4650 with a foot pedal for the steering adjust. The newer tractors are engineered to cost money.
@williamdowell7646
8 жыл бұрын
Nothing is ever easy. Seems like all jobs require a little blood and a little skin to be complete. Harbor sells a little air hammer with different punches that's great for knocking out pins, removing stuck riding mower tired, etc. cheap too. Take heart in the fact that tho you're losing blood your saving money. Those big damn hammers hurt.. I think hell I only drew it back 6 inches!
@kevinwillis9126
8 жыл бұрын
wes when putting the pin back in. get it started then use a c clamp to finish it of works good on things like that....
@buffalostate1
8 жыл бұрын
man , u need a nice workbench in that huge shop.
@XSniper16
8 жыл бұрын
Looks like one of those damn roll pins.
@connerputz2975
8 жыл бұрын
nice vid
@t.c.bowling1934
8 жыл бұрын
What a pain! Funny how something seems so simple yet takes so much work.
@bicycleyoda9301
8 жыл бұрын
for working in small spaces like that a compressed air palm hammer would probably work ok
@Jaydw4
Жыл бұрын
I ended up using a large pair of channel locks, and was able to squeeze the pin out. Don’t buy the after market cylinder it doesn’t fit perfect. The original pin holding the lever was too big and I had to grind a bit of the groove out to get it to fit. And in the end the steering wheel won’t go all the way tilted
@Jaydw4
Жыл бұрын
Also compress the cylinder slightly before installing it so you can get the bolts in the top easier
@Mebob2001
8 жыл бұрын
you need an air hammer buddy, buy a GOOD one and you will love it... that new astro one that SMA is using sounds Epic...
@B.E.Long.63
8 жыл бұрын
Ya that's it YA right Tim,Oh ya the Pandy man can..
@clearingbaffles
8 жыл бұрын
so where is the actual reassembly with all the 4 letter words, I was looking forward to learning more about the same time? LOVE YOUR CHANNEL
@lukestrawwalker
7 жыл бұрын
A box full of ratcheting box ends and you come back with a goofy regular box end... go figure... LOL:) Bout like my brother when he helps me in the shop... Later! OL J R :)
@codyflenthrope2388
8 жыл бұрын
I have done a few of them. if I remember the spring keeps the handle one way and to prevent it from vibrating
@kglefo
8 жыл бұрын
I look forward to your videos each day and when they don't appear (I'm guessing that earning a living trumps posting videos on your farm) I feel disappointed. No, I should say I'm addicted to your videos and when they don't appear I get desperate! Yikes. So, please post more videos (oh, alright.; you can earn a living, too.) :-)
@timengland3649
8 жыл бұрын
Those acidic oils sure can leave a burning sensation. Gramps always sprayed a puddle of WD40 into his palm and scrubbed his hands with it before he worked on anything. He swore the WD40 kept him from getting irritated and it also helped his arthritis. A time way before rubber/latex gloves.
@karjack11
8 жыл бұрын
i use it to wash oil and grease off my hands, never thought to use it as a preventive
@ronaldhamilton3133
8 жыл бұрын
air hammers are amazing for those kind of problems
@guscole6386
8 жыл бұрын
Piddly stuff is always a pain.
@bradsteigerwalt6718
8 жыл бұрын
Wes you weren't kiddin on the howfarmswork livestream! You did upload.
@newyorkfarmer146
8 жыл бұрын
Wow I have the same puller
@johnmills186
8 жыл бұрын
Looks just like the one I put in my Cat tractor only you had a lot easier access. (That means you were doing it and not me.) And you didn't use near as many bad words as I did.
@cmans79tr7
8 жыл бұрын
I think he was pulling our leg about that spring. Was this recorded on April 1? That's a heckofa job to have to re-do just to install that spring. It's improbable that he mistook that spring in a cup for the guts of the hydraulic cylinder, the cylinder may have leaked, but it was still intact. But it did worry me that he put that pin in extra tight....
@oldpackfan
8 жыл бұрын
Wes I have a small puller for battery terminal that might work for pushing one of those pins out You could borrow it but it's 1000 miles down I 95 so check at napa.
@kenmelrac
8 жыл бұрын
You had the same problem as another reported, the pin is the hardest part to remove. Shame they didn't use a bolt instead of a pressed in pin.
@janvandenbos7085
8 жыл бұрын
Wes that spring you find, you did not put that back 😂
@johndeere2054
8 жыл бұрын
The bolt is welded fast. Changed the same cylinder (70 $) a few months ago. Punched it out.
@noc8076
8 жыл бұрын
Air chisel, works every time on stuck things.
@ozlakota1
4 жыл бұрын
the next job i need todo
@andrewkiwi1
8 жыл бұрын
Hi Wes, Did you put that spring back in?
@key420gen
8 жыл бұрын
+andrewkiwi1 I hope he did!
@MrEfarmer
8 жыл бұрын
+andrewkiwi1 rattle, rattle, rattle
@jbmbanter
8 жыл бұрын
Jan below and I are wondering about the little spring that you put aside. Could it be that it was there to return the handle to a neutral position when not wanting to raise or lower the steering wheel?
@travishook5302
8 жыл бұрын
that spring belongs in there.
@kingredleg6747
8 жыл бұрын
+Travis Hook It is there so the handle does not make a rattle noise in the cab. But yes its was obvious that the spring needed to be installed.
@FILIPFROMSALMO
8 жыл бұрын
don't get hurt, my retirement is watching you so be good
@Ham68229
8 жыл бұрын
Could've used those vise grips on that punch, would save your hands from that hammer. :)
@patamos7019
8 жыл бұрын
Two fluids I despise getting on my hands.....brake fluid and antifreeze. Both of those make the skin on my hands feel weird!
@tomscorner3838
8 жыл бұрын
Tim would have gotten it out without any problems...... lol
@ruthannwilliams6890
8 жыл бұрын
+Thomas A Sprouse TIM IS A ASE MECHANIC
@QuadcopterAnalyze1980
8 жыл бұрын
You should have used a vice grip on that punch
@abc-coleaks-info3180
8 жыл бұрын
You beat me to it, but yea. It keeps the meat tenderizing off the job.
@carls.5433
8 жыл бұрын
You should get an air hammer there great just noisy
@user-nq6qp8kp6i
2 жыл бұрын
Hello, I have a Jandir 7810 tractor and I encountered the problem of reverse gear error code 017/052. I need your help.
@jankotze1959
8 жыл бұрын
What was the spring that you find in the device, I did not see you putting it back, nice video.
@jbmbanter
8 жыл бұрын
+Jan Kotze I had the same thought and wondered if the spring was there to make the activator handle return to like a "home position." I bet he'll need it.
@jankotze1959
8 жыл бұрын
Ya, I thought so as well
@jbmbanter
8 жыл бұрын
Jan Kotze Whatever he did, it's working now. He always seems to end up standing up on his feet with his mechanical jobs. He's like the battery guy he just keeps going and going.
@jankotze1959
8 жыл бұрын
Ya, his ability to fix stuff is mind blowing
@williamdowell7646
8 жыл бұрын
Btw best penetrent I've ever used is 50/50 acetone and trans fluid. Bottle of finger nail polish remover add some t fluid,, cheap
@robbiegwinn
8 жыл бұрын
did he fall off the tractor? where did he go
@davesmith2479
8 жыл бұрын
Repaired mine weld a washer each end and fit a coil spring cost ? Found spring in workshop
@janvandenbos7085
8 жыл бұрын
Instead of the pin you could put a bolt in works easyer I think 😊
@heatherbynum2771
2 жыл бұрын
Thank you for the idea! Thats exactly what we just did!
@jackewich7
8 жыл бұрын
I'm frist HI wes pandy how are you
@jblack1854
8 жыл бұрын
In the first video, the packaging for the new part referenced a web site for additional installation instructions. Might be a good idea to check it out. WTF....why make everything so difficult???
@clearingbaffles
8 жыл бұрын
will this edited video be called how to or how not to? Love your channel
@gordieleblanc2619
8 жыл бұрын
wouldnt the spring be there to stop the handle from rattling
@HowFarmsWork
8 жыл бұрын
Bloody hands or someone here will mock you for using a chicken stick. There's no winning really haha.
@zachgunn746
8 жыл бұрын
Its gotta stink to be good!
@daleolson3506
8 жыл бұрын
The manufactures should be forced to recall and fix this kind of junk that they sell us then they would maybe clean up their acts
@famerboi1
8 жыл бұрын
when i replaced mine it seemed easier to push from right side with a punch
@paulc8581
8 жыл бұрын
I know that knuckle is gonna be hurting later..
@yz490w
8 жыл бұрын
What about the spring?
@Nate-fs3no
8 жыл бұрын
for the love of god put that spring in the new one !
@joetiller1031
8 жыл бұрын
What a pain in the ass to get to, pb blaster does stink but it works, not much cussing I know why, his Mom told him to cool it haha.
@beaverrick9789
8 жыл бұрын
Hate jobs like that, no room to work.
@magrowj1
8 жыл бұрын
need some light
@clearingbaffles
8 жыл бұрын
ice and shrink it
@KPearce57
8 жыл бұрын
WHAT NO AIR HAMMER?
@michaelmckinney890
8 жыл бұрын
first
@shawndinterman2219
8 жыл бұрын
2nd
@gearypeel3411
2 жыл бұрын
Invest in a air hammer
@tdavis7580
8 жыл бұрын
How many of y'all ducked when the pin come out. I did. LOL
@TheTomBevis
8 жыл бұрын
+tdavis7580 I smacked myself in the face, once, while doing something similar. lol Good thing I was wearing safety glasses.
@advandervelden1588
8 жыл бұрын
comment
@remigagne450
7 жыл бұрын
Soon you will have to put a warning before your video to let people there will be blood and violence in them.
@markgutekunstdc2516
8 жыл бұрын
it would be nice if you would use a work light so that we, your viewers, can see what the hell u r doing
@paulc8581
8 жыл бұрын
3rd lol
@orkidknog4147
8 жыл бұрын
very dark and cant see a thing very poor
@jaywest4102
8 жыл бұрын
If you curse in only one language it couldn't have been that bad a job.
@bigtrucker26
8 жыл бұрын
*note I find that when it comes to rusted fasteners, if it won't come off with a mix of PB Blaster, and Amsoil MP (metal protector), it aint gunna come.... -- get the torch/drill/saw....
Пікірлер: 104