Thankyou. Right to the point. Made my research easy. Now i can go outside, swap mounts and get my 327 in the whole today. Thanks again brother.
@superc4308
6 жыл бұрын
Great info bro i have a project truck with a v6 planing on swaping to an v8
@shaggydoop
4 жыл бұрын
Dude I could kiss you... I just pulled my tires off and planned to rip out the coils out and was like screw let's see if there is another way and I did both sides removal and install in under 20 minutes. Thanks!
@Joe_Jackstands
4 жыл бұрын
Glad I could help.
@CoolCarsKJ
5 жыл бұрын
Are the nuts on the bottom the same size as the bolt heads? Bolt head looks to be a 15mm.
@Joe_Jackstands
5 жыл бұрын
I cant remember off the top my head but there a 15 or 17mm. Do the driver side first it's a little easier and you can check the nut size a little easier.
@roberttrevino4581
9 ай бұрын
Thanks for the video, makes life easier. But a complete newb question, why not just cut the bolts off the V6 mount? TIA
@Joe_Jackstands
9 ай бұрын
You can cut the bolts makes it easier. But alot of people said you couldn't unbolt them so I made the video to prove them wrong
@171apples171
3 жыл бұрын
Dude thank you. Ive been looking for a video that shows exactly which holes the new mounts use. I want to use long tube hooker competition headers on a plain old sbc. Do you think they're gonna fit? I have the external slave NV3500
@Joe_Jackstands
3 жыл бұрын
Yes it should fit no problem. The nv3500 should just go right in thous trans came stock in 92-up c1500
@nickdonato7367
5 жыл бұрын
Looking to do the same project does the original transmission work with the bigger engine?.
@Joe_Jackstands
5 жыл бұрын
If your going to a older stay 350 it should. I went to a 5.3 ls swap and used the ls 4l60e in it
@fatallykinky8886
2 жыл бұрын
What did you use to get the engine to adapter with the older 4l60e and how'd it run? If not looks like I'm gonna have to get a 99-06 4l60e
@ChefboyRD253
Жыл бұрын
This is crazy helpful. Thanks!
@Joe_Jackstands
Жыл бұрын
Glad I could help
@brianhess4777
5 жыл бұрын
I’m doing this in a 96 with same motor mount holes. Do I just use the same clam shells off the 4.3 to the v8 motor mounts?
@Joe_Jackstands
5 жыл бұрын
I had to use v8 clamshell cause there different than the v6 ones
@brianhess4777
5 жыл бұрын
I figured that out after doing a bit more research. I was trying to use the v6 motor mounts, v6 clam shells as well as the lsx innovations adapter plate on an LS 5.3. Now it does work with that setup. The problem is... the 5.3 is pushed back to far and hitting the fire wall. So I’ve learned that you have to have the v8 motor mounts along with v8 clam shells for this to work. Thanks for getting back with me 👍🏻
@funguy7979
2 жыл бұрын
I have a 97 sierra V6 2wd 5spd. Is there any engine that'll bolt up to the V6 mounts or do I need to buy a kit with mounts to put a V8 ? What v8s are available to swap with these kits?
@Joe_Jackstands
2 жыл бұрын
None that I know off. The v8 mounts on rock auto are cheap. Just have to fish the bolts up thru the holes
@FzlMusic
9 ай бұрын
If you swap the v6 to a v8 do you have to change the transmission
@Joe_Jackstands
9 ай бұрын
You can use the v6 trans on these years
@terrynolder6976
4 жыл бұрын
Im tryin to do the same thing but I was told you could use the v6 4.3 mounts for the 327 v8 ? But I don’t know which way to flip the mounts
@Joe_Jackstands
4 жыл бұрын
I heard of people flipping mounts but im not sure how they did it. I would just switch to v8 mounts and clamshells
@ricardoderobles9494
3 жыл бұрын
Will same ECM computer work. I am working on a 93 from 6 to 8 TBI.
@Joe_Jackstands
3 жыл бұрын
It should being all the same sensors but idk for sure. I would think fuel maps might be different on a v8 but to get it running im sure it would
@jsc0338
5 жыл бұрын
What motor mounts did you buy? I’m also trying to do the same v6 to v8 6.0
@Joe_Jackstands
5 жыл бұрын
I used stock 350 motor mount pads and the dirty dingo sliders on the ls engine.
@Akumacokezz6
4 жыл бұрын
Did you have to move the transmission crossmember at all for your ls and 4l60e set up?
@Joe_Jackstands
4 жыл бұрын
Nope. it all bolted into the factory holes.
@Akumacokezz6
4 жыл бұрын
Joe Jackson Perfect, thanks for the response
@josephlegocki6750
4 жыл бұрын
thanks man...
@slaskey
3 жыл бұрын
Does the V8 mounts go in the same exact place?
@Joe_Jackstands
3 жыл бұрын
Yes they go in the same spot
@slaskey
3 жыл бұрын
@@Joe_Jackstands thanks so you do lots of those is my first time and I appreciate you answering my questions saved me some time
@darkrose4704
3 жыл бұрын
Do you have to swap out the tranny as well??
@Joe_Jackstands
3 жыл бұрын
Yes you can use your stock trans if your staying with a tbi 350
@jaylsx8823
6 жыл бұрын
Can you reuse the v6 harness without modifying it ? Or should you just replace it with the v8 harness ?
@Joe_Jackstands
6 жыл бұрын
If your putting another tbi motor in all the wiring should be the same just switch to a v8 ecu.
@jaylsx8823
6 жыл бұрын
Huh , i was talking to my boss earlier about this and he told me i would have to use the v8 harness . Ill probably just do that just in case
@Joe_Jackstands
6 жыл бұрын
i never done a v6 tbi to a v8 tbi motor. i usually convert to v8 mounts then ls swap these trucks. as far as i know the tbi harness is the same between the motors. i dont think there is any different sensors. the 4.3 is the same as a 5.7 just minus the 2 cylinders. If you have a chance to get a cheap tbi harness get it just in case but i would think there the same on the trucks.
@jaylsx8823
6 жыл бұрын
All right man thanks for the info !
@Joe_Jackstands
6 жыл бұрын
No problem. if the harness are different let me know. thanks
@usmcM16kid
5 жыл бұрын
where did you get your v8 motor frame mounts?? thank you
@Joe_Jackstands
5 жыл бұрын
I got them from rockauto
@rogervillela8241
2 жыл бұрын
Cut mine with the blow torch
@Joe_Jackstands
2 жыл бұрын
That makes it real easy lol
@k.lamareyev4418
5 жыл бұрын
Do u wanna sell the v6 mount brackets?
@Joe_Jackstands
5 жыл бұрын
I would of just gave them to you but they are long gone sorry.
@k.lamareyev4418
5 жыл бұрын
@@Joe_Jackstands thanks anyway
@Benjocold
5 жыл бұрын
i can sell you mine. about to take them out any day now. Im in Georgia.
@k.lamareyev4418
5 жыл бұрын
@@Benjocold what year do you have?
@k.lamareyev4418
5 жыл бұрын
@@Benjocold just watched your cruise control video. You have the v6 vortex engine, I need the v6 tbi frame mount brackets like in this video. Yours are different. I'm doing a ls swap in mine soon but still wanted to run the v6 for awhile longer. Thanks for trying to help.
@jamessmejkal8803
3 жыл бұрын
Too mush movement got a headache.
@shootermcgavin2819
2 жыл бұрын
another ls swap..
@Joe_Jackstands
2 жыл бұрын
This video is from 3 years ago but even then it was still played out
Пікірлер: 59