Ah this takes me back. My uncle tranined me over there, I started with a 20" Sheffield cross cut and a Disston i still have both and the bit and brace drill and egg beater too. I was recently given all his tools in their boxes. Such history. I was explaing to my son that these were what i started with no cordless he nearly fainted 😂😂😂
@thetallcarpenter
9 ай бұрын
Hi Gerard🖐I wish I'd have kept all my old hand tools, as I had all the same as you describe👍Thanks for your comment and for watching 😎 Cheers Del
@ianlewis1180
7 ай бұрын
Back in 1988 when I started my apprenticeship and before health and safety regulations we used chain saws ( I know!!) for joist lifts, birds' mouths and compound roofing cuts. I think a year or two later they were banned on sites and I missed them. In 93 Hitachi made a portable 12 inch cross-cut compound mitre saw, it cost a fortune and weighed a ton. We used to argue who would carry it up the scaffold 😂😂 I haven't been in the industry for year's I got fed up arguing about money however, this really takes me back!!! Especially cutting jack rafters by hand when the timber had a huge cup in it!!!
@thetallcarpenter
7 ай бұрын
Hi Ian🖐We started with in a few years of each other, and your recollection of how it used to be brings back all sorts of memories🤩Thanks for watching and your comment 😎 Cheers Del
@Pete.Ty1
9 ай бұрын
👍👍👍 I still have my saw I bought 50 years ago. Occasionally I sharpen and reset the teeth. Sometimes it's just nice to work without the noise. Thanks
@thetallcarpenter
9 ай бұрын
Crickey, you still got it all these years later👍Nice👊
@jimgeelan5949
9 ай бұрын
Woodford water pumping station mid 1970s,full on winter, wood dripping wet, cold, miserable days, I thought I remembered all my apprenticeship days with joy but you have just put me right back there 😂
@thetallcarpenter
9 ай бұрын
I agree with you Jim🤔they aren't all golden memories😵💫Cheers
@richardh4389
9 ай бұрын
Being the apprentice I had to sharpen the saws, and set them. Still have my triangle file, but lost my set years ago. Imagine cutting an entire roof with only a hand saw, and a Yankee screwdriver for putting screws in!! Don't know there born now adays.
@thetallcarpenter
9 ай бұрын
It's seems hard to believe nowadays Richard that we did EXACTLY that, and entire jobs, including joists, floor boards, studwork, roofing skirting and architraves were all cut with handsaws🤯Cheers Del
@stuartandrews4344
9 ай бұрын
Must be almost a lost art nowadays, still have my kit from my apprentice days.
@shaneelson
9 ай бұрын
I used to watch my dad sharpening and setting the teeth on his saws on a Saturday afternoon so he'd start the next week with fresh teeth. I still have the hand setting tool somewhere in the shed.
@thetallcarpenter
9 ай бұрын
That's amazing Shane👍and also used to sharpen my saws on a Saturday(hated doing it though) Cheers Del
@jonathanpike5879
8 ай бұрын
Yep back to 1986 all hand tools wasn’t allowed to use power tools until I could use a hand saw memory lane
@thetallcarpenter
8 ай бұрын
Hi Jonathan🖐Yep, and even then the only power tools were a circular saw and a noise, percussion hammer drill🙃Thanks for watching 😎 Cheers Del
@jonathanpike5879
8 ай бұрын
Yep all done by hand out in Oz now all the best
@alanmooney
9 ай бұрын
Ah yes the stanley pump driver!!!!
@thetallcarpenter
9 ай бұрын
Was a great day when I got my first Yankee Alan💪
@alanmooney
9 ай бұрын
Very well done Del !!!! I'm 70
@thetallcarpenter
9 ай бұрын
Fair play Alan🫡And you were hand cutting roofs for at least 15 years more than me😶Cheers
@daihedral9269
9 ай бұрын
Still got my Diston in the shed. Don't think I've used it in 30 years.
@thetallcarpenter
9 ай бұрын
That's mind blowing bud😎
@thelatemickb6927
9 ай бұрын
63yo sometimes forget I've got a skillsaw that goes to 50 degs. God bless saint. Bahco.
@thetallcarpenter
9 ай бұрын
Forgetting things on a regular basis is something we all seem to do as we get older bud😵💫Thanks for watching 😎 Cheers Del
@stuartandrews4344
9 ай бұрын
Those were the days Del, youngsters have it easy today..
@thetallcarpenter
9 ай бұрын
You're right Stuart🤔
@markrobinson1458
9 ай бұрын
First saw i ever owned was S&J with the wood handle, it was secondhand but a mile down the road was a saw doctor, he got it razor sharp again, not seen a saw doctor in decades, you didn't throw them away back then 😂🪚👍
@thetallcarpenter
9 ай бұрын
Hi Mark🖐I think my first saw was also a S&J and I didn't like filing and setting it at all. I did sent it to a 'saw doctor' once, and as you say, it was AMAZING when it came back🤩Cheers Del
@iansherman6638
9 ай бұрын
Good exercise Del.Get the Yankee pump screw driver out next .😂Remember them .
@vespagd67
9 ай бұрын
Still have mine in the garage also using slotted screws😊
@stuartandrews4344
9 ай бұрын
@@vespagd67 Still have mine😊& I been having a sort out here & found some old Rawlplug plugging tools with Made In Gt Britain on them..😮
@thetallcarpenter
9 ай бұрын
I sure do Ian🤔and I also remember how great it was when I first got one💪Although I will say, that if my battery driver broke, there's no way I'll start driving screws in by hand😵💫Cheers Del
@thetallcarpenter
9 ай бұрын
Nice one👍Mine disappeared years ago😬
@thetallcarpenter
9 ай бұрын
That's vintage stuff now😉
@dennishughes3250
9 ай бұрын
Cordless. Nice.
@thetallcarpenter
9 ай бұрын
Cheers Dennis🤩
@garyc4943
9 ай бұрын
When I was an apprentice (about 20 years ago) my employer made me use hand tools first before the power tool alternative. He said it was better to learn the hard way before the easy way, especially incase a situation arose where a powertool wasn't an option.
@thetallcarpenter
9 ай бұрын
Hi Gary🖐I agree with your early employer, and the basics should be mastered a little even if they're not regularly used😉Cheers Del
@charranjitsingh6742
9 ай бұрын
WOW my dad made me do this and practice hammering so you could do it in one swing, this brings back memories
@thetallcarpenter
9 ай бұрын
Hi Charranjit, hope you are well bud👍Sounds like you dad knew how to raise his boy👊Cheers Del
@Kiss4cooper
9 ай бұрын
Most of us over 50 probably have dementia and can’t remember…… 😂
@thetallcarpenter
9 ай бұрын
Remember what🤔😆
@Kiss4cooper
9 ай бұрын
@@thetallcarpenter flat feet….
@Dazza19746
9 ай бұрын
Who what where when why?
@disklamer
8 ай бұрын
Waterproof, never shorts or needs new brushes, the trigger will not stick, break or lag, drop-resistant up to any height, lightweight, and operationally low risk. What’s not to like :D
@thetallcarpenter
8 ай бұрын
Love this comment bud😁🤗Nice
@pauljackson5482
9 ай бұрын
Wonderful sir. Nice full use of the whole blade, and perfect finger alignment. Mr sellers will be proud. Most of my work is with the old stuff, it never let's you down. And all you need is a stone and a file and your good to go again in minutes. Cheers
@thetallcarpenter
9 ай бұрын
Thanks for you comment Paul🤩and like you say, we could do so much work back in the day with no power tools whatsoever🤔Cheers
@richardwood4541
9 ай бұрын
I’d say the same about swinging a hammer all day as well whilst knocking on 4” round heads 👍🏻🔨
@thetallcarpenter
9 ай бұрын
I absolutely agree Richard👊and I'd actually say that my hammer skills are in decline due to using a nail gun all the time😬I don't think I could sink 4" wires like I used to😶Cheers Del
@michaelplays2449
9 ай бұрын
Great video Del !!! Youre a top class Crafts person , a joy to watch.......thank you !!
@thetallcarpenter
9 ай бұрын
And you're a top class KZitem commenter Michael🤗
@isaacshenton9330
9 ай бұрын
As a 19 year old apprentice I know just how lucky I am, learning with mitre saws and circular saws.
@thetallcarpenter
9 ай бұрын
It's certainly easier on you body Isaac👊All the best bud😎Cheers Del
@arthuranderson7741
9 ай бұрын
impressive stuff...
@thetallcarpenter
9 ай бұрын
Thanks Arthur🤩
@Ultimate-roofing-square.
9 ай бұрын
Love it Del. 💪🏻🪚
@thetallcarpenter
9 ай бұрын
Cheers Dan🫡(I've given that saw to the brickies now😉)
@Ultimate-roofing-square.
9 ай бұрын
@@thetallcarpenter spoiled them. 😆
@TheToolnut
9 ай бұрын
I'm forty six Years old now T.C and I've done a lot of hand cutting over the Years. I always carry at least one good Draper handsaw in the van. There will always be a place for hand tools but one needs the skill and an eye to use them. That takes a bit of time. No wonder us middle aged chippies have arms like gorillas, 👍😁💪💪🔨🇮🇪🇮🇪
@thetallcarpenter
9 ай бұрын
Hi TN🖐You're right, it does take many years of practice to become proficient with a handsaw, and as you say, you should always be able to fall back on one if needed👊Cheers Del
@TheToolnut
9 ай бұрын
@@thetallcarpenter 👍😁💪🔨🇮🇪
@Wattsjoinerybarn
9 ай бұрын
Superb demonstration, I passed a fair few of these up to old boys when I started and always with my fingers crossed😂 I was lucky enough to be using the worlds heaviest 9inch skill saw by the time I was doing my own roof’s! One of the blokes who trained me used a chain saw for these cuts and tbh he actually got good results! I would saw your cut is better than most with a power tool! 💪🏻
@thetallcarpenter
9 ай бұрын
Hi bud🖐I provably hand cut roofs for about 5 years before I started using a circular saw, which is obviously much easier and quicker👍Thanks for watching 😎 Cheers Del
@SteveAndAlexBuild
9 ай бұрын
No school like the old school . I was taught how to use a hand saw by a bricky 🪚. Slow down , use the whole length of the blade and let the teeth do all the work .👌🏼🤙🏾🤙🏾🧱👍🏽
@thetallcarpenter
9 ай бұрын
It really is a simple as you just put it Steve💪Cheers bud🤩
@inspiringbuilds
9 ай бұрын
Nice cut and good exercise getting the heart rate up time to time. You’re right, the tools now days are another level just lining it up and barely requiring any effort.
@thetallcarpenter
9 ай бұрын
You're quite right, and today's tools certainly speed things up and make it easier on the body👊Cheers Del
@TheBadgolferman
9 ай бұрын
A mate of mine used to rough cut it and then use the belt sander to make it perfect. Yeah, he was a bit bonkers and it took longer but he could produce anything to perfection. His OCD was off the scale! I do love a bit of roofing.
@thetallcarpenter
9 ай бұрын
Hi bud🖐If you watch my coming bastard hip video you'll see me mention, and use, a block plane to finish off my compound hip plumb cut👍
@davedawson9851
9 ай бұрын
Eyup Del. Days before power tools? Well we used to get up two hours before we went to bed, eat half a cup of cold poison, crawl to work on us hands and knees, work a twenty five hour shift for no pay and when we got home, Dad used to murder us in cold blood wi 't bread knife. But we were happy. And if you tell that to kids these days........
@thetallcarpenter
9 ай бұрын
Surely this is from the Four Yorkshiremen/Monty Python🤔It's stretching my memory now but I think they also talked about only having gravel to eat😆Love this comment👍
@davedawson9851
9 ай бұрын
@@thetallcarpenter Cold gravel. If we were lucky. 😂😂 I am the fifth Yorkshireman!
@chrisdavies6633
8 ай бұрын
It’s so satisfying to do it by hand we didn’t have any power tools
@thetallcarpenter
8 ай бұрын
Too right Chris👍Cheers Del
@JACKATTACKED
9 ай бұрын
Pieces for that saw next episode 😂 Not rushing the cut helps 😀not having come on, hurry up in yer ear 😂
@thetallcarpenter
9 ай бұрын
You know it bud, and as you say, if you start 'pushing' the saw, you'll soon go offline😬Cheers Del
@andrewplatt
9 ай бұрын
It's good to keep your eye in using a handsaw 👍 served my time with a bloke who used to use a bow saw! I couldn't get the hang of it😅
@johnmackay7789
9 ай бұрын
Same here.
@thetallcarpenter
9 ай бұрын
Hi Andrew🖐I never actually witnessed anyone using a bow saw, but I did a bit of my time under a guy who used an axe🤯(not for roofing)😵💫Cheers Del
@thetallcarpenter
9 ай бұрын
Bonkers John😵💫Cheers Del
@stevehallam6495
9 ай бұрын
Until throwaway saws became as cheap as a bowsaw blade I used a bowsaw too. Axe is still in my toolbox in the van but don't see much use now.
@johnmackay7789
9 ай бұрын
@@stevehallam6495 my axe was primarily used to make wooden dooks when "dookin" stone or brick mortar joints, along with the dookin iron. Also known as "plugin" in other parts of the country.
@johnmackay7789
9 ай бұрын
I/we used to try so many ways to get as straight a cut as possible and it ended up coming down to a new sharp saw. Sounds obvious but back in the day having spare new saws was a real luxury so sometimes you just had to persevere with what you had until the rep from the local ironmonger did his site visit. £5 for a Sandvik Hard Point in 1985 wasn't that cheap.😊
@thetallcarpenter
9 ай бұрын
You're so right John👍and I couldn't afford to spend £5 on a hardpoint saw in the late 80,s as I was only on £20 a week😵💫(I had to give my mum a fiver for board and lodgings😲) Cheers
@s999geo
9 ай бұрын
Back in the early 70s wee used to spend a friday afternoon sharpening our saws how life has changed 😅
@johnmackay7789
9 ай бұрын
@@s999geo I know what you mean. When I started in 84' I had a full set of Distons in with my kit provided by the firm (paid back at £5/week) I tried so hard to keep them sharp, either by myself or to the local saw doctor. But it was £5 for a sharpen and set from him when a Sandvik HP was £5. And the HP lasted so much longer.
@VicNorth2023
9 ай бұрын
My favorite hand saw was the Sandvik 288. Black plastic handle and chrome side plates. The Skilsaw 77 killed off the handsaws here; way faster and less tiring but they'll eat your leg as quickly as a 2' X 4" wall stud as they aren't particular!
@thetallcarpenter
9 ай бұрын
Hi Russ🖐I also remember my first hardpoint saw, AND when I started using a circular saw for roofing🤔As you say, the circular saw can bite a whole lot worse than the handsaw😬Cheers Del
@paddy120
9 ай бұрын
👍
@thetallcarpenter
9 ай бұрын
Cheers Paddy 😎
@garvielloken3929
9 ай бұрын
Nooice!
@thetallcarpenter
9 ай бұрын
Cheers Garviel😎
@vicinglis3736
6 ай бұрын
Hi TC, just catching up... oh yes remember it well
@thetallcarpenter
6 ай бұрын
Hello there Vic🖐Long time no hear. Hope all is well and thanks for looking in🤗Cheers Del
@bricklayersworldwithandy6277
9 ай бұрын
Still have a sawmill near me.
@thetallcarpenter
9 ай бұрын
Hi Andy🖐That's pretty cool mate, as there isn't many left now😬Cheers Del
@bricklayersworldwithandy6277
9 ай бұрын
@@thetallcarpenter 👍
@jordaneastern6971
9 ай бұрын
Well said sir.. and yeah youngsters should learn to hand cut these.. shame the old ways are dying out to the modern tech. Not much hope for the youngsters to learn the traditional PROPER OLD SCHOOL carpentry these days. As you say pull the trigger. That said there is no Pasload training in schools ( demo would have to suffice due to insurance works). They come out of college totally unprepared for what the real sites are like. That’s the mismatch of education and site currently. If only carpenters on site had the time to train youngsters up like they did in the old days. But it’s all price work and should have been done yesterday attitude. Shame really. I have a set of old distons my uncle gave me for a joke/ Christmas present and he said here you go sharpen them up.. So I KZitemd it.. and had a go.. now I have been doing them ever since and keep them in the van just in case i forget to charge my battery kit up. Lol.. a sharpened rip saw cuts just as fast as a skill saw.. if you put them board to board. Works for back up. Won’t get kids learning them. That said they are making a comeback in the states.. people are using them again. Better quality.. but has its ups and downs. Good to have the power tools.. but yeah don’t forget the old ways. What if there was no power on site to charge up? Want to hump a generator around all day? And with power tools it’s all cost.. Hand tools you buy once and if you look after them.. they will last a life time. Some thing to be said about the old ways and a old school carpenters kit.. No power tools used on Shakespearian houses ey? Worth thinking about. A balance of old and new is a good thing when it comes to kit. 👌😊
@thetallcarpenter
9 ай бұрын
Hi Jordan🖐I can't even start to work through responding to your great comment, as it would take forever, as I totally agree with all you say, and we are definitely heading for big problems in the construction sector in the near future for all the reasons you list😬Cheers Del
@jordaneastern6971
9 ай бұрын
@@thetallcarpenter cheers for the lovely comment bro. 😊
@patchedupdemon7104
9 ай бұрын
My hand sharpened diston would have got through that in half the time, can't believe you think those saws are better than the old saws. Let's see what that saw looks and cuts like in 200 years time
@thetallcarpenter
9 ай бұрын
I hear what you're saying, but in my experience, my freshly sharpened saw would lose its edge LONG before these hardpoint saws, and you have to factor in touching up an older saw at least once a week, which I found tedious😬Cheers Del
@stevehallam6495
9 ай бұрын
a newly well sharpened Disston would be better than a hardpoint cos of the added weight in the blade. It would need half an hours sharpening tho by the weekend.
@barryford7135
9 ай бұрын
Still got it Del. 🚴👍
@thetallcarpenter
9 ай бұрын
I surprised myself Barry, as I cut a further three rafters to the same standard😆Cheers
@joecondon4901
8 ай бұрын
If you do a 29 degrees cut the opposite way then you can run the circular saw square with the 29 degrees cut and that will give you your 61 angle.
@thetallcarpenter
8 ай бұрын
You're spot on Joe, and that is how I find the the 61° angle to mark these cuts👍However, it's a very precarious cut to make, and the cut is well over 75mm which is too deep for a circular saw😬Thanks for your comment 😎 Cheers Del
@moomastico
9 ай бұрын
I think the term your looking for with regards to the youngsters dell is ‘don’t even know you’re born’ 😂
@thetallcarpenter
9 ай бұрын
That's exactly right bud🤔Thanks for watching 😎 Cheers Del
@alistaircameron3237
9 ай бұрын
👌👌🤣🤣
@thetallcarpenter
9 ай бұрын
Cheers Alistair 🤩
@PaulFurness_run26
9 ай бұрын
Box of 10 saws back in the day £50, bargain back then.
@thetallcarpenter
9 ай бұрын
Hi Paul🖐I remember back in the late 80's when the Jack hardpoint saws were starting to become more popular, thinking, 'I can't afford £5 for a saw' 😵💫I was only on £20 a week🤯Cheers Del
@attlee1945
9 ай бұрын
Next week a brace n bit
@thetallcarpenter
9 ай бұрын
I don't think I wanna go test oldschool bud😲
@kevinchamberlain7928
9 ай бұрын
Diston's were for ripping but yes, I had a Spear and Jackson panel saw that needed topping, sharpening and setting until the the Sandvik Blue Handle came along. They are now called Bacho and not as good IMHO. We old muthafukka's got those cuts absolutely bang on. I have done whole roofs with a chainsaw - and still will if the H&S assholes are not involved.
@vespagd67
9 ай бұрын
Remember them still have one in the garage and sloted screws 😊
@thetallcarpenter
9 ай бұрын
I was horrified when I first saw a roof being cut with a chainsaw, until I tried it, and, as you say, you could be very accurate with thim😎Cheers Del
@Redbeardcarpentryco
8 ай бұрын
Old boys!! 😮 I’m only 33 and I spent the first 5/6 years only using a hand saw! 🤣
@thetallcarpenter
8 ай бұрын
Well, compared to the lack of youngsters in the trade now, you are an 'old boy'😜
@Redbeardcarpentryco
8 ай бұрын
@@thetallcarpenter cheeky buger! 🤣
@thetallcarpenter
8 ай бұрын
@@Redbeardcarpentryco 😲😊👊
@davetaylor4741
9 ай бұрын
I used to prop mine up so the line I was following was vertical. Just found that easier. On massive big inverted hip trees. Or even oversize rafters and beams. I often reached for the chain saw. Used to work on a lot of Oak barn conversions. And also repair things like tythe barns. Oast houses etc. We would make a lot of the parts from green Oak using chainsaws. Handsaws, and chisels. Saw skills. Hammer skills. And a lot of hand tool ability. Gradually disappearing. Here is a question for you. You use a conventional disposable cross-cut saw. The action becomes second nature. You can buy those two way teeth things. What I call a push me pull me saw. Can you cut with one of these. I can't. I catch a crab on every back stroke. I also bought a Japanese saw. People rave about them. Can't cut with that either. They are pull saws. My head and muscle memory just go haywire. Do you have the same problem or is it just me.
@thetallcarpenter
9 ай бұрын
Hi Dave🖐The more I read you comments the more I realise that we are VERY similar people🤔Like you, my habitual use of tools, plus muscle memory makes it hard for me to try/use different functioning tools😬I got in a right mess trying to use a pull saw😶Cheers Del
@paddy120
6 ай бұрын
Quality 👍
@thetallcarpenter
6 ай бұрын
Thank you bud🤗
@AxleM8
9 ай бұрын
Any tips on getting the 2 way cuts on the hipboard correct on a irregular hip. 2 45's doesn't work of course because of the difference in pitches. Is there any definite way to know the angles or just trial and error? Thanks.
@thetallcarpenter
9 ай бұрын
Hi there🖐I've got a video coming out showing how I set out and cut a bastard hip, and as you say, the hip and jack rafter bevel cuts are not 45°. On the the steeper pitch it's a simple case of setting the saw over to the hip angle, (this will always be less than 45°), and then following the hip plumb cut for the hip, and the rafter plumb cut for the jack rafter👍The bevel cut for the hip and jack rafter on the shallower pitch can also be cut with a circular saw, but is limited to how far the saw will bevel cut. My saw Has will bevel over to 57° so if the hip angle is no greater than this, the saw can be used by simply following the hip and jack plumb cuts. However, if the hip angle on the lower pitch side is over 57°,(or the maximums bevel capacity of your saw), then you will need to make these cuts by hand. I have yet to find a formular/way to accurately find/deduce this angle, and just do it by cutting the hip angle up the jack rafter plumb cut, and then offer it up and adjust if needed by planing or re cutting. Even then it's important to remember that the hip bevel cut will still be different to the jack bevel cut because the pitches are different😵💫I don't know if that makes any sense🤯Cheers Del
@TopCatsBack
9 ай бұрын
Off topic here but need advice for a bricklayer ...had my trusses spread and braced other night ( only 4 of them ) and just noticed middle Truss has 700 mm one side and 500 other side inside to inside ...should I move it over ?
@thetallcarpenter
9 ай бұрын
Hi there🖐If it was me, (which it has been in the past), I would alter them to be at the correct centers. I don't think leaving them as they are would cause any structural issues, but it might cause other problems down the line for things like plasterboarding👍Cheers Del
@TopCatsBack
9 ай бұрын
@@thetallcarpenter it was fine , I was just panicking and reaching up with the tape not accurately reading it ...🫣 . I'd have porridge every morning if I was hand cutting .
@liamjohnny335
9 ай бұрын
Use all that blade Dell...no short cuts buddy 👍
@thetallcarpenter
9 ай бұрын
I do my best Liam👍Cheers
@paulmcgeoch2603
9 ай бұрын
Most of us over 50 will have a bastard hip or 2 😂😂😂😂😂😂
@thetallcarpenter
9 ай бұрын
Love this comment Paul🤣Although only one of my hips is a bastard🤔The other ones a bitch😲
@paulmcgeoch2603
9 ай бұрын
@@thetallcarpenter hahahaha
@jpgmusic2563
9 ай бұрын
How would you cut an angle that steep with a circular saw?
@thetallcarpenter
9 ай бұрын
I don't think you could even if a saw could go over to 62/63° as the cut is about 80mm deep🤔
@jpgmusic2563
9 ай бұрын
Yeah that’s what i thought 😊 cheers for reply. 👍🏻
@kiwigrunt330
9 ай бұрын
What's wrong with hand sharpened Disstons? Or Spear & Jacksons. Well, mine are probably getting a bit blunt. Or very blunt. Haven't sharpened them in at least ten years. I also find that they are running out of charge. Not sure what that's about....
@thetallcarpenter
9 ай бұрын
Hi KG🖐I found hand sharpened saw tedious, not only to sharpen, but the fact they went dull very quickly😬Cheers Del
@miller745
8 ай бұрын
Were you out of breath after cutting that? 🤣
@thetallcarpenter
8 ай бұрын
Err, no....😮💨😆
@cabottaxi
9 ай бұрын
That will keep you fit. Pretty sure I have the same saw in the garage😀
@thetallcarpenter
9 ай бұрын
I guess you're right bud, and staying fit can't be a bad thing💪Cheers Del
@joinertanner
9 ай бұрын
Isn't life unfair when young and inexperienced you need to relay on expensive tools you can't afford to do a job well and when experienced and able to afford the better tools we can do the job with a cheaper tool.
@thetallcarpenter
9 ай бұрын
What a great, and reflective comment🫡Cheers Del
@michaellinahan7740
9 ай бұрын
..... and we used to lick road clean with our tongues! Tha' doesn't know you were born.
@thetallcarpenter
9 ай бұрын
Love this Four Yorkshiremen' stuff🤩Cheers Del
@richardstevenson2727
9 ай бұрын
🫡
@thetallcarpenter
9 ай бұрын
Thanks for watching Richard🤩
@johnmorrissey1675
9 ай бұрын
No problem , just want to check the Ambulance is ready to go 😅☘️🇮🇪🩼👏
@thetallcarpenter
9 ай бұрын
I always keep my phone in pocket John, just in case🤪Cheers
Пікірлер: 156