As the owner of an '81 SC, I definitely appreciate your channel!
@zakash613
Жыл бұрын
A tip for the ending issue with clearance, if you take the new piece of metal and try to align it with the tabs you can see if the tabs will fit through and if not then you can do a little sanding to open up the hole.
@ethans1103
3 жыл бұрын
thank you so much for this video, my door stay guide snapped in half yesterday, i had very few tools, and i couldn't get the pin out to shut the door.finally fixed it cave man style to get proper tools to remove. following this vid to replace.
@christian1127
2 жыл бұрын
Excellent detail!
@davidwillsie
Жыл бұрын
I plan to do this with my 924S - very helpful to see you running through the process. Thanks!
@afternoongarage
2 жыл бұрын
Thank you for all your good video work here. It is really tough getting a camera into the spots you did and get good video!
@dayonept
2 жыл бұрын
thank you for making this easy to find on youtube and follow.
@DSM911M
Жыл бұрын
Perfectly described thank you !
@foxlair3682
2 ай бұрын
Thank you for all your excellent and thoughtful videos(and website). I have an 83 SC as well and have to do this. On another note, my SC did not have an oxygen sensor, so I replaced that and the relay on the unit under the passenger seat, but almost seemed to run worse. I’m not running a cat, but stock muffler. Scratching my head on that. Replaced the WUR with a new one, but still doesn’t really start the way it should. Runs strong otherwise. Guess I have more work to do!
@JoeEngineer
2 ай бұрын
You may need to reset your mixture again so it runs right with the new O2. Check my other videos for that.
@foxlair3682
2 ай бұрын
@JoeEngineer Thanks man!
@Hezath
2 жыл бұрын
Great video! Thanks for sharing. I'll be doing this shortly.
@PhillipTieuChainz
3 жыл бұрын
I appreciate you creating this video, it really helped me!
@luisdejesus2570
7 ай бұрын
Good Job... excellent instructions.
@DanMan68
3 жыл бұрын
Super helpful!! I need to do this to my car also
@filou1200
2 жыл бұрын
Thanks will be doing this soon on my 78sc
@gregoryaltmeyer9084
3 жыл бұрын
Thanks. Need to replace on my 76S
@benjaminferary4773
3 жыл бұрын
Hi Joe, Great Video ! keep the good work. i had to do the same for the same reasons. unfortunatly forme the damage inside where bigger than yours and i had to adapt 2 bigger plate. One question : in your set it seems that they gave you a glue to fix the plate on. did you use it? i would advise to do so, because in my case i figure out that with time and car vibrations the bolts seems to loose out and you might have some play between the metal pieces. i know that i have to redo it all over again cause i didn't use glue as well. keep posting man.
@oibal60
2 жыл бұрын
At 20:10 Did you not try to put that wire on the 'outside' of that plate? Aaah, 22:25 I see you did. Atta boy!
@mtdesign184
3 ай бұрын
With all due respect, the outside plate won't fit through the hole unless I grind it down and then it compromises the ability of the plates to stay in place. I tried it with similar plates and the whole mechanism just pushed through. The option then is to buy a new door and not stay with the original metal. I decided to put a plate on the inside with an eye bolt through it and use a strong nylon tie to link the door and the frame. It's a simple solution and will only annoy the purists. After all, it's a 50 year old car.
@JoeEngineer
3 ай бұрын
If it works it works 👍
@merlepaul2576
3 жыл бұрын
Merci beaucoup
@ErrorMargin
Жыл бұрын
How did you get the outside plate into position? It seems to be to big to fit into the hole
@JoeEngineer
Жыл бұрын
If I recall, I was able to maneuver it from the outside of the door, with the string attached of course.
@jamilwakil5085
Жыл бұрын
I must have a smaller outside hole as well. No way that outside plate is going through that hole. I will have to hammer it in, then try to fix the damage to the skin after.
@ErrorMargin
Жыл бұрын
@@jamilwakil5085 I figured it out, the plate goes in angled, you can see it in the video here: kzitem.info/news/bejne/l2ppx4yrp3-elpw
@jamilwakil5085
Жыл бұрын
@@ErrorMargin that hole has either been enlarged or is bigger than mine. I think it looks like the back part of hole has been cut out more. Anyway I had to make minor cuts and then hammer it in. Of course I tried different angles.
Пікірлер: 28