Haha yeah! I have been ther too two years ago - beating the snot out of things until they bend or break, then torching it... great fun! Have been anxiously greasing every single part since then so nothing rust-welds itself again. Love your humor, great video!
@thisnameisboring6005
3 жыл бұрын
I know nothing about cars, nor even drive, but for some reason this shit is entertaining
@jakevendrotti1496
2 жыл бұрын
Same here. This person has good vibes and the topic is really well explained.
@kailuafrog
2 жыл бұрын
Thanks for that video friend! The Bentley is a big help but you and other people like you taking time to share are an absolute treasure. That's what the intertubes were supposed to be, a tool for sharing knowledge! My advice to you is to get an impact wrench, 20 bucks on Harbor Freight will save you a LOT of time and make your life so much easier!
@pdxmack
4 жыл бұрын
Mark all the camber settings before taking things apart! It makes it easier to drive to the alignment shop. Safety note: use the stock jack location for the jack stands. Have the floor jack under the steering brace. If the jack stands fail, you will have time to get out.
@cryptonerd7337
25 күн бұрын
Vanagon Camber is pain in the ass
@willemmaas9813
3 жыл бұрын
Thank you for a detailed video showing how to replace the rubber bushings. I own a 1996 model T25 with a VW factory fitted 2.6i five cylinder engine. The suspension of my vehicle differs slightly from the video footage you posted. Here in South Africa VW discontinued the T25 Bus in 2003. Ever since it is a struggle to acquire new OEM replacement spares. Because the 5-cylinder version T25 was only produced in South Africa, workshop manuals also was never published. It is very helpful though to see videos such as yours to make maintenance easier to do yourself.
@viktorholmelin8022
4 жыл бұрын
Great content! Wandered around the internet for why a car might lean to one side, ended up here and found a trove of interesting stuff. Thanks for providing inspiration and stoke!
@DoogieLabs
4 жыл бұрын
This is the reason I make these videos! Thanks for the love!
@MakeItMetal
10 ай бұрын
Great video, i'm about to embark on this very task today. Very helpful
@amandafitzwater242
3 жыл бұрын
I don’t understand much of what you’re talking about but when i do I’m typically laughing at the few little dry jokes you pop in there. 🤣 bfh, cigarette, peckerhead, and sweet little nothings caught my attention. Makes learning new things more interesting. Thank you!
@vveerrgg416
2 жыл бұрын
as a noob about to jump down this rabbit hole of mechancis work... I truly appreciate this video. Thank you for posting it and for being pretty much straight up entertaining ... props to your work ... and may your projects always be a success . Stay awesome
@patrickpiche5507
3 жыл бұрын
What a perfect reference! Thanks for the last part of complete assembly in full speed. I'm doing all this with big brakes and helping me a lot.
@nmartin5551
3 жыл бұрын
Appreciate the tips and suggestive press name/description! My Vanagon needs this too. I’m going to to start this week with penetrant oil. Maybe try next week.
@midreal6667
3 жыл бұрын
Awesome video... Thanks for making this. I do all the work on my 86 westy and while everything is a challenge its always fun to do it yourself and learn. This is one job I will be doing in the near future. I have dreaded this a little and watching your video helps confirm the dread somewhat LOL but also makes me more confident in tackling it. Great job and Thanks!
@DoogieLabs
3 жыл бұрын
If you have your own press, you'll find it much easier to get those PITA balljoint bolts out. If you have any questions when you go to tackle all of that please let me know!
@eliottpreston165
3 жыл бұрын
great video! I'm going to reassemble my front suspension later today and being as I disassembled it over a year ago I couldn't exactly remember how it all went together so your video has been a huge help :)
@whooshding7164
2 жыл бұрын
GOOD VIDEO!!! Thanks for the tutorial. I am now aware of potential pitfalls and will be prepared prior to taking on this project myself.
@2xixaaxu
3 жыл бұрын
thank you ... have been thinking of replacing my suspensions.....good reference video ..thank you
@vwforever4131
3 жыл бұрын
We bought a set of GW 16 inch rims for our westy last year, but I wanted to replace all the front end bushings first as well as the springs before we installed the new wheels. After watching this video, I appreciate even more the time and skill necessary to get those old bolts off. On second thought, maybe I'll just take it to someone who knows what they're doing and pay them. Great video and resource!
@DoogieLabs
3 жыл бұрын
Thanks! If you have a shop press on hand like I used later on in the video that is the immediate go to solution and always replace with new hardware, that is the ideal solution I think for those three bolts.
@cyneater6300
3 жыл бұрын
Love the commentary reminds me of either a cooking or holiday show. Its all correct accurate and uses the correct terms. How did you do it with out praising engineers or using curse words? Not sure if this is meant to be a bit of a satire ! Hmm I almost want to dub over it with my best bogan Voice and curse words ! Using more correct words describing how awesome engineers are!
@stewarteastep9577
3 жыл бұрын
Great stuff! Was looking for a full suspension rework like this. Prefer to do it all then just a bushing here and there.
@4RingsRetro
4 жыл бұрын
Great commentary! 😂 I have a UK Vanagon, the T25. It's a 1987 DG Petrol. I've had one previously and I may end up buying another soon as a project. Such good fun!
@Mnpctech_Giveaway_PC_Mods
4 жыл бұрын
Nice doogie, watching while I’m working in shop late tonight
@garyp.7501
3 жыл бұрын
T3 has an excellent anti-sway bar replacement and hd-links. That will make your ride even better. And BMS upper control arms have better bushings and are easier to get the wheels in alignment.
@rextilian
6 ай бұрын
I read somewhere that one should never use heat on suspension components due to metal weakening concerns? Also great video and explanation, thank you!
@SomeMorganSomewhere
4 жыл бұрын
gotta love that commentary ;)
@photopicker
3 жыл бұрын
This is completely nuts. That's why I pay the $$$ to have pros do this.
@tonvanderreijken4380
3 жыл бұрын
wonderful video, I bookmarked it for future use in spring 2021 thanks a lot !!!
@Earthboundllc
2 жыл бұрын
thank you for your effort. You rock!
@Ricopolico
2 жыл бұрын
Get a 2lb. copper hammer, it will become your best friend.
@tongy876
3 жыл бұрын
Good video demo!
@ryandb009
2 жыл бұрын
your commentary is funny
@JohnSmith-oj3uu
Жыл бұрын
The small round metal bushing one that slides on the damper that came with the Bilstein shock out of the box, where did you use it in the reassembly? Did you leave it on and force it into the bottom of the bumper. You will see the metal sleeve bushing on the new shock at Timestamp 6:57
@JohnSmith-oj3uu
Жыл бұрын
I asked my vendor Gowesty the same question here is their response - "That spacer needs to be inserted up into the bump stop. If you are having issues getting it into the underside of the bump stop, you can use a little lithium grease on it. It is necessary to use it as without it the top nut will run out of threads, and the shock won’t fully tighten down"
@lukeholland4434
3 жыл бұрын
This is a great how to video for suspension upgrades. Thank you! Looking to do this on my own camper with the GoWesty lift springs. Curious, did you have to use a special tool to press the tie rod end or steering knuckle ball joint out?
@cryptonerd7337
25 күн бұрын
I have a question, can i add leaf spring in the front suspension in the vanagon
Пікірлер: 43