I got mine today in the UK. Ordered Friday & today is Monday so really it was 24 hours. Packaging is amazing for a product in this price range. Extra nozzles & 2 spare carbon fibre arms that actually had me thinking I was 4 arms short until I remembered that the 6 are already fitted. Also got needles to clean the nozzles & it is pretty amazing that they included something like that. Proper instructions too. The general finish & quality seems superb. I haven't really tried it yet but I'm sure if there were problems, Anycubic would help as I've heard they reply to questions & have good aftersales. Edit: The only problem I just found is that after watching many reviews, I ordered stepper motor dampers & found they've already fitted them!!! Proves they listen to reviewers!
@NULLDIVISIONofficial
2 жыл бұрын
Bruh I did the same thing almost 2 years ago with the whole ordering stepper motor dampeners, freaking hilarious. It's amazing that they already included them!
4 жыл бұрын
An addition from my personal experience with the printer: If the leveling does not seem to work at all (one side OK, the other side 1cm in the air or similar) check the worm screws on the steppers. On my device they forgot to tighten both (!) screws on one side. This was only visible after the stepper for removed from the column.
@skippy18
4 жыл бұрын
What do you mean exactly? Can you send a Picture? I am having the same Problem
4 жыл бұрын
@@skippy18 No I can't send a picture here. But to clarify: Remove the three main columns again, remove the 4 screws on the stepper motor plates to get the stepper motors out. Check the two little worms screws in the geared wheels sitting on the axis of the motors.
@skippy18
4 жыл бұрын
@ okay, thank you!
@Arckivio
4 жыл бұрын
@Beau I think he meant grub or set screws holding the pulleys on.
@TALKCalgary
4 жыл бұрын
You have some very informative videos but adding commentary would make them even better.
@medusa90210
4 жыл бұрын
Grazie mille
@to-zesantos5987
4 жыл бұрын
where do I find LEVER_TEST.gcode file
@EnergySeeker
4 жыл бұрын
can you install a hotend on this printer which can do 450 degree ? if yes how please ?
4 жыл бұрын
what do you ned 450 degree for?
@EnergySeeker
4 жыл бұрын
@ peek and carbon fiber
@NULLDIVISIONofficial
2 жыл бұрын
Probably would need to some major modding like replacing the board, and a direct all metal hotend as the anycubic firmware only goes up to 250 (even though itll say 260). Thats from what I've read anyways, I've never done it myself.
@EnergySeeker
2 жыл бұрын
@@NULLDIVISIONofficial not a big deal I got it finally I put an SKR PRO and a volcano and I also put a smart effector and magnet bars and also got reprap
@cutty02
4 жыл бұрын
This printer Leave diagonal lines in all of my prints. how can I fix it?
@spearhead3496
4 жыл бұрын
Diagonal on top or on the sides?
@cutty02
4 жыл бұрын
@@spearhead3496vertical side walls curved walls are fine.
@spearhead3496
4 жыл бұрын
@@cutty02 check this link: reprap.org/forum/read.php?178,763881 and this video kzitem.info/news/bejne/xJmpvpuFqoKeeZg. You'll find a very good reference for the issue. I'm going to install TL Smoothers for my stepper motors to get rid of the issues (all delta printers have that issue apparently) and I'm also taking the info in the above link to heart. I think that'll be a good starting point for you too.
Пікірлер: 20