Lookin to build a motor.. thank you for this guide video! Def subscribing!
@ferny9992
Жыл бұрын
I’m not much of a car guy but does this work with a B20B?
@UNIQUEGrills
Жыл бұрын
B20b is the bast for B20 vtec
@retrocny5625
3 жыл бұрын
This is the way to do it. There's so many guys out there who think you can just take a stock b20 block, strap a VTEC head on it, rev it to 8200+ rpm and be done with it. Good way to stretch a rod bolt at the very least. If you're gonna do B20 VTEC, do it right and save yourself the headache later.
@UNIQUEGrills
3 жыл бұрын
It’s not for everyone.
@uniquecraftycorner.5998
4 жыл бұрын
Awesome built. 🥰🤩🥰
@avianaviator1570
4 жыл бұрын
Awesome video man! Def gonna subscribe so I can see more. Working on putting one of these in my EF
@whatsbehindu
Жыл бұрын
what octane are you using
@UNIQUEGrills
Жыл бұрын
92 pump gas
@Indicafatbud
4 жыл бұрын
i grabbed the same pistions but .5 over and some brian crower light weight h beams for 540 watching this video makes me think i scored lol
@az_3kgt714
3 жыл бұрын
using ross 12.5:1(@92mm bore or.040 over) pistons and those BC625 lightweight rods as well. But in a 6g72 3.0l v6.
@az_3kgt714
3 жыл бұрын
awesome build. Doing a 12.5:1 na build on a 6g72 myself. Pretty sure 1 has never been done before.
@7eamGhast
4 жыл бұрын
Very inspiring, I've never done an engine build before, so the plastic you placed between the "main caps" (i think its called that) and the crank, is it only the space from the top or measure bottom space also? or does it even matter as long as you measure between crankshaft and caps? thank you for such helpful knowledge.
@UNIQUEGrills
4 жыл бұрын
Team Ghast Doesn’t matter as long as they all in line. Not like one on top and one on the bottom. Place them all on top or bottom. Using cap are is easier to see and measure.
@7eamGhast
4 жыл бұрын
UNIQUE Motorsports thank you so much, I appreciate you, subbed.
@startwithpraise3121
4 жыл бұрын
nice ride
@alfer9920
3 жыл бұрын
70 hp no more LOL your famous phrase.
@jaidawg9615
3 жыл бұрын
how drake builds an engine
@BBoyDrkNova
3 жыл бұрын
I have a question brother . I’ve never built an engine so I’m curious . Why send the block to balance rotating assembly?
@UNIQUEGrills
3 жыл бұрын
Those engines and the whole assembly is not designed to rev pass 7,2k rpm. So you need to balance to rev a lot more safely. I’m my case 10k rpm all day every day.
@Curtis1900
4 жыл бұрын
Love the build so far probaly will be my lsv guide
@polobreezy7748
3 жыл бұрын
building my first b20v is there a email i can contact u at? need more info with my build
@AlexMelnik
4 жыл бұрын
Awesome video!
@kishathfernando5814
4 жыл бұрын
Hey man. Watched all the videos! What's the fuel you're running this on and whats the final compression figures?
@UNIQUEGrills
4 жыл бұрын
Just 92 pump gas. Compression should be around 12.5:1
@HarryPNess-lu1lf
4 жыл бұрын
what head gasket and where to buy? doing my first build ever. b20V
@UNIQUEGrills
4 жыл бұрын
I have used Zerg High Compression head B20v 84mm gasket. It’s only two layers instead of standard 3 layers. They are on eBay for only $54 shipped.
@citystarridin
4 жыл бұрын
What’s the reasoning behind not using a reground crank? I used to grind cranks myself and we always had a set spec to grind to if needed. 90% Honda cranks we got only needed a micro polish. Only rod journals I had to grind was K series cranks.
@UNIQUEGrills
4 жыл бұрын
jcrabs93 regrinds wont hold up at high rpm. Will do ok with stock engines.
@citystarridin
4 жыл бұрын
UNIQUE Motorsports ahh I see, good to know
@kedaotuning
4 жыл бұрын
same bottom end here u gotta love it
@qaeedjulie5545
3 жыл бұрын
Hi can you list the setup, cams used?, what springs and retainers?
@UNIQUEGrills
3 жыл бұрын
Watch part 3 engine assembly. It’s all listed. Even price.
@Johnnie5213
4 жыл бұрын
👍👍
@Weezly707
2 жыл бұрын
What crank pulley was used?
@UNIQUEGrills
2 жыл бұрын
B20
@kswappedzingerbox738
4 жыл бұрын
notif squad lessgooo
@_gunner_kev_5466
4 жыл бұрын
Where did you buy the pistons and rods need them for my b20v lmk bro
@UNIQUEGrills
4 жыл бұрын
Kevin Ash eBay
@bseries8826
4 жыл бұрын
I subscribed!
@albertosantiago5151
3 жыл бұрын
Is there anyway i can reach out to you i have lots of questions
@UNIQUEGrills
3 жыл бұрын
Instagram Unique Motorsports
@mccoy8457
4 жыл бұрын
Did you machine balanced the crankshaft?
@UNIQUEGrills
4 жыл бұрын
Machine shop did. Yes
@jr_morillo
3 жыл бұрын
I see u in Washington maybe u can help me out with my ek?
@worldtraveler8613
3 жыл бұрын
Where do you get forged rods and pistons for only 500?
Пікірлер: 55