You need to rough the surface of the tab up with some wet and dry paper,then flux and pre solder,before trying to attach the wire,works first time every time,plus much stronger.
@cliveklein3076
8 жыл бұрын
Great video... You really need to use flux on new terminals and rough up the terminal heads using sandpaper or a sharp object for better bonding... I found this out when upgrading my istick 50w from 4400mah to 5600mah...
@SamA-rs5lk
8 жыл бұрын
nope fuck that ill just buy another one
@nathanjohnston6713
9 жыл бұрын
My iStick battery has just stopped taking a charge though the board seems fine. This is exactly what I was after. Thank you
@TamioxII
9 жыл бұрын
Just a hint, next time you want to solder something heat up the other side, a little bit, and you could also try soldering flux. Otherwise you get no joint or a cold solder joint.
@hunter11000
8 жыл бұрын
Love this song.
@anthonyfaccenda8274
9 жыл бұрын
great video, been looking around for a guide to do this :D
@elnapotandil
9 жыл бұрын
Madness rlz!! Buen video!!
@1MSRAVENCLAW
9 жыл бұрын
this has to be the scariest thing i ever saw, the very thought of my istick being opened is enough to give me nightmares lol. but it was nice to see whats on the inside. i'll leave it to the professionals thanks for the video.
@AlexTechie
Жыл бұрын
I like to picture myself doing a part of the process over and over again. In this case, take it out of the case, putting it back. This is actually easy considering it's just 4 screws, then removing the face cover of the buttons, then re-assembling. Soldering is different and actually costs money to buy all the equipment and time to learn to do it properly. It's well worth it, though, as many electronics that break are actually an easy fix to repair and far less expensive than buying a replacement.
@user-xv4ph6ly9t
9 жыл бұрын
thanks for the video
@khaibui3575
9 жыл бұрын
what is that metal sticker thingy you stick on the panasonic battery ?
@Davini994
8 жыл бұрын
Thanks, got me through it. What have you used for the contacts there though? I fortunately didn't have to touch any of that as it turns out just to be a solder point failure. Would be good to know for when the battery does go though.
@riccard66
8 жыл бұрын
+David Campbell solder only a little 'difficult try a couple of times
@Davini994
8 жыл бұрын
I was thinking about those folds of metal; did they come with the battery? Ive got ones with just a contact without that, that go in my mod. Thank you for the response :)
@AuralVirus
9 жыл бұрын
9:55 in need of flux?
@RoByQuarantasei
8 жыл бұрын
Ma le palette alla batteria nuova glie le hai messe tu o è già così??
@antoniojct
5 жыл бұрын
Hi I know this is very late in the thread, but I used the Samsung 30Q 18650 3000mAh 15A Battery and when i make contact to the points on the new battery the display screen comes up, but when i had them soldered on nothing comes up on the display? is 15A battery no powerful enough or is it the solder? I have 2 istick 30 watts and did this to both and both arent working
@toddmiller9562
9 жыл бұрын
This is my only complaint about this device. If you could just open it up, pop in a new battery and go, I would be satisfied. This is to much effort just to replace a battery.
@tarasenku
9 жыл бұрын
Thanks
@CMDRBlueeagle66
9 жыл бұрын
What battery would you recommend for an iStick 30w mod. Is there any higher than 2200mah that can safely handle 30 watts? Packed in smoking two months ago and haven't touched a cigarette since. The wife too :) Started off with standard ego batteries. Then moved up to an X6 for the both of us. Now I plan to purchase the Eleaf iStick and a Kanger Pro Tank 2. Forever upgrading :) But I think I will stick at the iStick and Protank. Lol. I even plan to build my own coils for the Protank to save buying new atomiser heads. And then I will make my own e liquids too! I have gone from noob to enthusiast in two months. KZitem has a lot to answer for IMO :) Thanks again.
@TheMWGamingChannel
9 жыл бұрын
Brian Hillard I have the same question.. Using a 30w 2200 mAh, but i'd like to upgrade the capacity (3000+ mAh). No idea where to buy these things and how to know if they're good for using with the istick. Got any answers by now?
@CMDRBlueeagle66
9 жыл бұрын
Randomination Hi mate. I have had my iStick 30w for about a week now, and at the moment I am happy with the battery life. Although I am no expert, but either a NCR18650BD. Or a Purple Efest? Take a look here too :) Although I haven't had the guts to take mine apart as yet! vapingunderground.com/threads/eleaf-removable-battery-mod-and-first-post-big-pics.31476/
@TheMWGamingChannel
9 жыл бұрын
Brian Hillard Thanks for the fast answer! I posted another comment above too. I found that NCR18650BD too, thing is I'm a total newb! I have no idea what the effect of a battery will be on my istick, will a higher mAh also lead to being capable of a higher wattage? I'm not trying to get higher in wattage, all I want is my battery life to be longer. My istick 30W battery lasts 2 days, drops really fast the moment when it's under 50%! Sorry for being a newb but I just want to get a greater battery life, without any risks of overpowering anything
@CMDRBlueeagle66
9 жыл бұрын
Randomination Don't worry:) As for the mah rating of both batteries. Yes the higher will usually be better. But with vaping as I understand. It all comes down to the maximum amps it can handle. And more importantly the lower mah battery may stand up better to higher discharge currents. So in fact may turn out better. But to be honest mate. There are so many stats with these batteries. So that are slightly overstated by the manufacturer as usual. I would look at the NCR18650BD though when my battery starts to choke! I bought my wife an Ipow 2 battery mod. It started off good, then oh dear. Randomly it throws up Low Resistance warnings. And zaps the battery when it does. I thought it was my coil rebuilds causing it. But no. No matter if I use a new Kanger head, or a wind a new coil with a higher ohms. It still does it. I will be buying her an iStick next.
@TheMWGamingChannel
9 жыл бұрын
Brian Hillard So it's best to stay with my 2200 mAh or upgrade to a 50W istick? By discharge you mean that it heats up faster and vaporizes more right? Also what do you mean by choke? When it's at the end of it's life? About the Ipow 2, you say you built your own coils? Might be badly coiled or just the pin that isn't connecting well so it can not read it off properly?
@TheMWGamingChannel
9 жыл бұрын
Could you help me? I have a 30W atm, 2200 mAh. I'd like to upgrade it to 3000+ mAh, any idea where I can buy batteries like this and wether they are safe? I don't want shit to explode or anything lol. Replacing this is already scaring the shit out of me cuz I know myself, I'm gonna make a mess out of it.. Edit: I found the ncr18650bd, do you think this will be safe? Also what does this mean: Battery rated voltage: 3.7V? Cuz I'm planning on using it up to 20W (6.1V) on my Istick, is this safe? Is it compatible with the device and will it be good?
@1977avellino
9 жыл бұрын
Randomination SAMSUNG 25R
@josephkwon9286
9 жыл бұрын
Can you do this without a soldering iron?
@riccard66
9 жыл бұрын
***** you should pierce the tongue aluminum. I think it works
@alyshehzad
3 жыл бұрын
thats battery is new
@laserk40
8 жыл бұрын
una domanda,la batteria nuova è da 3400mah?
@riccard66
8 жыл бұрын
+marcy busto si e' 3400, ma ti consiglio la samsung 25R e' meglio
@dodgydruid
9 жыл бұрын
Song is Our House not It must be love thought to say :)
@AuralVirus
9 жыл бұрын
3rd song is though... thought I'd say ;)
@siddharthamason
8 жыл бұрын
Good tech...hate music
@shadow.banned
6 жыл бұрын
🏠
@peterfaretra
8 жыл бұрын
Can't see what you're doing with that focus.
@acidponcho
8 жыл бұрын
will this work with a MXJO 3000mAh 35A?
@cliveklein3076
8 жыл бұрын
Yes, you need the exact same batterys,voltage,mah ect....
@mastmalang70hk
9 жыл бұрын
nicley done , i have my charging port is broken ,the inside piece or flat slot ,can you advice how to fix it
how to know when to change the battery my i stick 30 now 10 wat give no good vaping where it used to be so cool in 10 wat now i put 30 wat it seemes giving me same power as what it was in 10 wat it used to be i could not put 30 wat vape it could be battery is dieing ?
@helloworld6160
8 жыл бұрын
+soqrates hassan how old is it
@soqrattes
8 жыл бұрын
5 month
@helloworld6160
8 жыл бұрын
soqrates hassan if its authentic it should be fine because they use high quality batteries, but if its a clone or you ordered it on ebay it might be fake and using chinese cheap batteries and would need to be replaced. but by reading what you said again it might be your chip, you might not wanna spend money on new batteries solder them on ad go threw the trouble and it be the chip. i recommend using it till its toast and pickup a new mod with maybe removable batteries this time :/ sorry but the istick 30 isnt really a easy device to work on because its ment not to be taken apart. anyway hope stuff works out for you
@cliveklein3076
8 жыл бұрын
A changing issue is 99% battery related... Being 5 months old you can get it replaced... If brought from new...
@xosesantos
9 жыл бұрын
La soldadura no pegaba en la pestaña de la pila y despues aparece ya montada...? no se ve que fue lo que hizo...webas.
@tyrese1anderson
9 жыл бұрын
Is this a 18650 battery
@riccard66
9 жыл бұрын
Tyrese Anderson yes
@andrewkelly9986
8 жыл бұрын
anyone know what 1050mah battery is in the istick mini as i'm looking to buy a backup.
@riccard66
8 жыл бұрын
+Andrew Kelly prova smontare poi compri
@caschworr86
8 жыл бұрын
ciao, si può fare anche per la 40w ? che batteria si può montare? complimenti del video
@riccard66
8 жыл бұрын
+caschworr86 no,purtroppo le 18650 sulla 40w non ci stanno. l'ho cambiata ma ci devi montare una 18500
@caschworr86
8 жыл бұрын
+riccardo balzarotti scusa l ignoranza ma la 18500 si può montare allora?
@riccard66
8 жыл бұрын
+caschworr86 si, si puo' ma ovviamente rende meno,l'ideale e' trovarne una come l'originale.le 18650 sono troppo lunghe e non ci stanno
@caschworr86
8 жыл бұрын
+riccardo balzarotti grazie dell info.
@laserk40
8 жыл бұрын
gentilmente mi linkeresti una Samsung 25R che citi?anche senza alette,grazie
+riccardo balzarotti www.amazon.it/gp/registry/wishlist/ref=nav__gno_listpop_wi?ie=UTF8&requiresSignIn=1 questa mi sembra uguale,cambia le ultime cifre dopo (SDI),anzi sai cosa vogliono dire?
@CDam-bj9od
6 жыл бұрын
You really need to keep what your doing in the camera frame at ALL times, watching your fingers REALLY not helful
@ianadams4704
9 жыл бұрын
Anyone kno how to replace broken usb port
@riccard66
9 жыл бұрын
Ian Adams www.fasttech.com/products/3023/10010021/2245702-istick-20w-styled-vv-vw-apv-box-mod-control-module
@jasonwatson6785
7 жыл бұрын
finally someone with good taste in music. uggh these millenials..
@assistantto007
8 жыл бұрын
what a load of rubbish. you go from being unable to solder the terminal of the battery to the wire to 'miraculously' having it all wired up.
@gedvaug7139
6 жыл бұрын
you would probably get away with just jamming the wires and sticking them down.
@russmack7910
5 жыл бұрын
Yeah, but others have related what needs to be done. Some sandpaper, soldering flux, add some solder to the tab beforehand.
Пікірлер: 83