Most time I tried that, air was coming from the bleed nipple threads so it was quite hard to know when done...
@fabricobbletech
2 жыл бұрын
I had a bit of that as well but if you take the nipple and throw a single wrap of teflon tape on the threads it will seal it up. Too long explanation to fit in 15 sec clip though.
@Johann52005
2 жыл бұрын
@@fabricobbletech I made an adapter to put 12 psi of air pressure in the fluid reservoir, used it regularly for 3 years, worked quite well !
@fabricobbletech
2 жыл бұрын
@@Johann52005 that's definitely a good way to do it. I have that setup for my car but I bought it that way so +10 points for you lol
@michaelmace924
Жыл бұрын
Don't open it as much
@michaelmace924
Жыл бұрын
@@Johann52005 I'd like to see that. 👍👍
@888TMONEY888
4 ай бұрын
Did you fill the reservoir with dirty fluid? Lol also anyone reading this, better to use a wrench for this because you need to close that bleeder screw before you pull the hose off so air doesn't get back into the system
@fabricobbletech
4 ай бұрын
When you pull vehicles abandoned in the weeds, that’s pretty standard fluid condition lol
@matthewholzinger1042
2 жыл бұрын
You need a full fluid change after seeing that fluid coming out and in the reservoir
@fabricobbletech
2 жыл бұрын
It's getting a new master cylinder and full flush. I was just trying to get the old crusty components working temporarily.
@michaelmace924
Жыл бұрын
@@fabricobbletech everyone is a KZitem expert
@fabricobbletech
Жыл бұрын
@@michaelmace924 It’s on every platform. Some people are trying to lend honest advice but many others just want to tell you you’re doing it wrong or are an idiot lol.
@puppygadget3189
Жыл бұрын
Easier to just use a window cleaner hand pump and clear hose and container to shoot the old fluid in. Real simple
@evelynnveleni
7 ай бұрын
Okay i was probably using this machine wrong. Time to give it another shot. 😂
@TobyJacques
7 ай бұрын
Flush all that old fluid out buddy that looks awfully dirty lol.
@ronaldwilliams4053
7 ай бұрын
U need to redo this video the information would be great but it cut out and u can’t see what u doing on some parts
@misstrKevin
Жыл бұрын
Do you keep the top on the master cylinder? I tried doing this with two people and a homemade bleeder bottle and hose. I’m just going to get the right equipment and do it myself.
@fabricobbletech
Жыл бұрын
Honestly, the best way is with a pressurized power bleeder that uses pressure on the brake reservoir. The problem is that you need a specific adapter for each reservoir type because it has to seal. This vacuum method can work but you do have to use some thread tap to seal the bleeder nipple threads or air can slip past the threads. Leave reservoir cap open to allow fluid to easily flow out of the reservoir.
@willc9033
2 жыл бұрын
Think I luv her....
@wendigo2046
Жыл бұрын
The purpose of bleeding the brakes is to get the air out of the Brake calibers with this method you keep pumping air into the calibers. Unless you pump the brakes you’ll never know for certain that there is no air lingering in there
@michaelmace924
Жыл бұрын
You need more life experience
@ministryofwrongthink6962
Жыл бұрын
@@spark229 🤣🤣🤣 He thought it was putting air in! What a cute misunderstanding
@HazyTown01
4 ай бұрын
Dude, it's a VACUUM pump. As in it creates an absence of air in the bottle, sucking the fluid and air from the bleeder valve. It doesn't pump air into the bleeder, only sucks.
@markkouros6628
7 ай бұрын
I got one of these pumps and nothing ever comes out through the line ...
@mjyumping
7 ай бұрын
same, this have no power to get fluid to come out
@fabricobbletech
7 ай бұрын
Is your line clogged? Your bleeder could also be clogged. You’re limited to around 13 psi with vacuum. You also need to make sure your bleeder isn’t allowing air to leak around threads. Try wrapping threads with Teflon tape. This method is still limited. Be sure to take cap off reservoir and reservoir is full. They also make pressure power bleeders but you have to get special adapters for each reservoir. If you really need to blast out obstruction nothing will beat pushing on pedal.
@markkouros6628
7 ай бұрын
@@fabricobbletech yep that's right, I'll try the Teflon tape, but the pump and lines are new brake lines don't know but they're gravity bleed shouldn't be clogged.. I should have had Teflon in there the whole time ... but if not I use the bottle from the pump and get in and press the pedal ...👌
@axizepp
5 ай бұрын
what car is this?
@fabricobbletech
5 ай бұрын
Chevy LUV if I recall correctly
@dontanswer6930
2 жыл бұрын
Or just pump it...
@fabricobbletech
2 жыл бұрын
Hard to do by yourself
@lmr9512
3 ай бұрын
This is amazing for someone who lives alone, personally, I have a dad in my life, so the two person method is fine
Пікірлер: 40