Nice setup. Have you considered testing them with ~200° water running through the center section and maybe coupling an motor with speed control to the shaft? I have a theory the EFR, aluminum supercore specifically, normally leak oil on turbine side at very low shaft speed (idle conditions) at normal operating temps. Potentially caused by the higher thermal expansion rate of aluminum. All of my EFRs have done this and only remedy was oil restrictor >1mm
@802Garage
Жыл бұрын
This is an awesome test. Had never seen one like this. Really cool. Love these insights.
@suiteproductions
11 ай бұрын
Will be trying out this technique on an EFR 9180 in the next couple of days which I suspect as some heavily worn oil control rings, thanks for the guide
@s4060
Жыл бұрын
Great you do that. Borgwarner EFR are the best turbo available! Just a great product!
@alexandreperreault584
2 жыл бұрын
Thanks for your time man, your video are instructive!!!
@abdullaalameri90
Жыл бұрын
Very creative way for a fast inspection. Really like it. So what about a turbo with a blown seal. Will it leak upto 100 ft3 or even more?
@on3tvracing
3 ай бұрын
Do you guys rebuild the efr? My seals are def blown.
@workturbo
3 ай бұрын
Not at the moment...parts availability are really in a bad spot for these at the moment. Maybe try my friends down in Tampa @boostlab , tell them I sent you! -Reed
@strokerz2858
Жыл бұрын
Using a smoke machine will allow you to visually see the exact location of the leak
@workturbo
Жыл бұрын
It is passing by the seal ring on the compressor and turbine side. Turbochargers do not have a positive seal on either end, hence the brand new one passes air by the seal. Most of the issues on a used one will be around the exhaust seal, we cap the compressor inlet and outlet to perform an isolated test at this point to verify. Quick and effective. Reed
@daveroy9906
2 жыл бұрын
👍Turbo, speaking of crank case venting is it better to use recirculating with vacuum or atmospheric depenting on volume of a baffle can or could you run both?
@workturbo
2 жыл бұрын
A proper high performance system will always include both. The "positive" or "PCV" will make sure the engine stays free of moisture and helps with oil flow control around the turbocharger gas seals (vacuum being applied). Once the vacuum is removed (PCV checks closed) you have to have a path for the crankcase pressure to escape (Crankcase breather/catch can/etc) It is very important to make sure the PCV valve checks closed under boost pressure...especially if the boost is raised from stock levels or if the car was not a factory turbocharged model. Hope this makes sense! Reed
@user-cc8gb1zo8m
7 ай бұрын
You can’t test seals like this. It’s the pressure in the turbine and compressor that make the seal. The only argument could be the compressor wont make seal until the pressure increases enough to overcome the vacuum behind the wheel.
@workturbo
7 ай бұрын
The seals are "gas" or "air" seals as you are implying. Pressure does not really care which direction is is being applied from. We have a fixture that will pressurize the seal from the outside the turbine or compressor, but we find that deformation from the housing heat cycles/corrosion etc creates variables in the results. This method of testing eliminates that as a potential source of leaks, but it does not let us isolate from compressor seal/turbine seal delta easily. As I think I state in the video, this is just another "tool" we have in our possession to quality control to a standard we set as "pass/fail/questionable" This test actually came from an Engineer at BorgWarner, while not published in public domain, it was very well distributed to shops that could benefit from the information. I have been using this method for internal QC with great success, and I think others could gain from the knowledge. Thank you for your criticism, it will help me with future video content. Reed
@n.prince2458
Жыл бұрын
Not bad video. Is the BorgWarner 9174EFR the best BorgWarner for a BMW M3 f80?
Пікірлер: 15