Finally someone who took their time to show clearly how it's done good camera work thanks
@allenjohnson6402
4 жыл бұрын
At least we know it’s specifically. Leaves no doubt.
@suzieq8379
3 жыл бұрын
lol
@user-lm9sf6le5n
Жыл бұрын
❤
@FumblingButtons
Жыл бұрын
Drinking game... Take a drink everytime he says specifically lol...
@FunkyGOB
4 ай бұрын
Could you be more specific to the rules?
@thornbush17
22 күн бұрын
I'm drunk
@obfuscated3090
3 жыл бұрын
Nicely shot, detailed PROFESSIONAL video.
@user-lm9sf6le5n
Жыл бұрын
❤
@joshcoe4319
3 ай бұрын
Thanks. Got mine running way better now. Always thought it was a little sluggish..
@saleemkader2126
3 жыл бұрын
Thankyou for sharing your knowledge my rpm is too low now i know what to do,
@Chuncy566
3 жыл бұрын
What would make on a Briggs 1 cyl vert. , the throttle plate& the governor lever ossilate back & forth ,(engine speed go up & down rapidly) . it starts up quickly, you have to keep the choke on pretty much or it will die..carb Cleaned out ,wire,carb cleaner, blown out all passages new needle valve,seat looks in nice shape, not flooding, more starving for gas. Thank you for help
@user-qv8df9vj2o
2 ай бұрын
Mine was surging extremely bad and i tryed everything. New carb, plug, air filter, bigger jet , coil and ended up the governor spring needed adjusted
@user-li2tp5ql4v
Жыл бұрын
Thank you for your through explanation.
@samuelhurst3536
Жыл бұрын
Mine runs at at full throttle even when the throttle level is all the way down. I can slow the engine down by pushing the linkage next to the choke, but it springs back open all the way when I release it. Any idea why it wants to stay at full throttle?
@rogerthat.9105
Жыл бұрын
Have you figured it out….mine is doing the same thing….
@mikencrew8885
3 ай бұрын
So I thought it was my governor so I tried to adjust that now it doesn’t run good at all and stalls out. I put the full throttle on and turned governor clockwise and tighten. Is that correct ?
@dickcreamer6898
3 жыл бұрын
I recently purchased a used lth 1538 husky previous owner had a new carb, plug and fuel filter put on. Starts hard and runs fine at low speed but sputters at higher rpms. Any clues? Thanks
@ocrun6765
2 жыл бұрын
I got the same problem when I put the throttle up to high. Did you ever find out what caused the problem?
@FriggOff361
2 ай бұрын
You saved me!
@mhess427
6 ай бұрын
I just replaced the carburetor on the same engine which is great because it runs but now I’m having another issue. It doesn’t seem to come off full choke after starting although the linkage looks fine. Do you know what causes that?
@1833Saloon
Ай бұрын
All the sudden I have no throttle at all
@Bigpoppi1469
2 жыл бұрын
there is no "triangle" piece on mine. just looked. the throttle isnt working at all. 1 speed. no fast no slow. chokes it down when you get push tbe throttle to the choke position.
@LesterFrazier-ul4so
Жыл бұрын
Having same issues basically except I'm having an extremely high ideal issue so should I try bending that tang down a hair
@justinberry3991
Жыл бұрын
That's what i got from this. He bent up to raise so bending it down should lower i guess.
@justinberry3991
Жыл бұрын
Bending up would put more tension on the spring and bending down would put less tension on the spring
@rogerthat.9105
Жыл бұрын
Hey how did you make out.. I am having the same problem
@robloxmaster8089
2 жыл бұрын
I have a 1995 toro 12-38XL 71184 and it make a click noise when i turn the key?
@AndreSuzano
4 жыл бұрын
I have a Toro Vtwin 656cc that was blowing white smoke. I cleaned the carburetor and did an oil change. (Fuel in Oil) Now I have a very low idle and engaging the blades kills the engine. Thoughts?
@donutz1
4 жыл бұрын
When mine blew white smoke I also cleaned the carburetor and did an oil change, diving deeper the head gasket blew. I would start checking a few simpler things before diving deeper. Check there's nothing hung up in the blades, look under the deck. Check your safety switches, here's how kzitem.info/news/bejne/0aGenH-Pgox8dqQ Good luck!
@kurayami3857
3 жыл бұрын
Exact thing happened to me
@ifitsnotbrokendontfixit9548
Жыл бұрын
When it dies when you engage the blades it means either you have a bad safety switch or your mower deck pulleys are bad or your mower deck stoppers are stuck unengadged my lt 1000 had that problem I changed the pulleys then it ran find for it having gas in the oil that means your float is not floating or it's getting stuck down best bet is a new carberator
@taunzik
3 жыл бұрын
I need to know how te springs are behind this! Do you have video? 2:25
@bindig1
Жыл бұрын
Thank you
@fredrickvoncold
8 ай бұрын
I dont see whats so bad about the mower , it had bad gas and a dirty carb, small adjust . It is going to have bad gas if its used.
@carlosmorgan8123
2 жыл бұрын
Question When and how do you adjusting the spring I don’t see just talking
@olsim3663
3 жыл бұрын
Any idea why my new carburetor running high even on low throttle
@kurayami3857
3 жыл бұрын
Same have you found a fix?
@stumpnc
3 жыл бұрын
Same. Looking at the carb, when I throttle down the butterfly only closes slightly. I can close it all the way with my finger. But it springs back to the 3/4 open position. I'm looking at the linkage on the one you have here, and seems to have a little bend to it. I don't believe mine does, so I'm going to check on that tomorrow. But if you have another solution all help is welcome. Thanks
@stumpnc
3 жыл бұрын
I don't know if this is a new carb. This is a new to me mower.
@SNIXC
3 жыл бұрын
@@stumpnc did you look at rhe screw infront of the governor?
Пікірлер: 44